TANDBERG C20 Administrator's Manual page 32

Quick Set C20/C20plus
Contents Introduction
Contents Introduction
current version supports http://tools.ietf.org/html/draft-ietf-sip-outbound-20.
On: Set up multiple outbound connections to servers in the Proxy Address list.
Off: Connect to the single proxy configured first in Proxy Address list.
Example:
xConfiguration SIP Profile 1 Outbound: Off
xConfiguration SIP Profile [1..1] Proxy [1..4] Address:
The Proxy Address is the manually configured address for the outbound proxy. It is possible to use a fully
qualified domain name, or an IP address. The default port is 5060 for TCP and UDP but another one can be
provided. If Outbound is enabled, multiple proxies can be addressed.
Format: Compact string with a maximum of 255 characters.
Example:
xConfiguration SIP Profile 1 Proxy 1 Address: ""
xConfiguration SIP Profile [1..1] Proxy [1..4] Discovery:
Manual: When Manual is selected, the manually configured SIP Proxy address will be used
Auto: When Auto is selected, the SIP Proxy address is obtained using Dynamic Host Configuration Protocol
(DHCP).
Example:
xConfiguration SIP Profile 1 Proxy 1 Discovery: Manual
xConfiguration SIP Profile [1..1] Type:
Experimental/Siemens>
Enables SIP extensions and special behaviour for a vendor or provider
Standard: Should be used when registering to standard SIP proxy like OpenSer.
Alcatel: Must be used when registering to a Alcatel-Lucent OmniPCX Enterprise R7 or later.
Avaya: Must be used when registered to a Avaya Communication Manager.
Cisco: Must be used when registering to a Cisco CallManager version 5 or later.
Microsoft: Must be used when registering to a Microsoft LCS or OCS server.
Nortel: Must be used when registering to a Nortel MCS 5100 or MCS 5200 PBX.
Experimental: Can be used if auto is not working Note! This mode is for testing purposes only.
Example:
xConfiguration SIP Profile 1 Type: Standard
xConfiguration SIP Profile [1..1] URI:
The SIP URI or number is used to address the system. This is the URI that is registered and used by the
SIP services to route inbound calls to the system. A Uniform Resource Identifier (URI) is a compact string of
characters used to identify or name a resource.
Format: Compact string with a maximum of 255 characters.
Example:
xConfiguration SIP Profile 1 URI: "sip:name@example.com"
xConfiguration Standby BootAction:
Preset6/Preset7/Preset8/Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/Preset15/
RestoreCameraPosition/DefaultCameraPosition>
Decide what the system is going to do on boot.
D14489.01—JULY 2009
Getting started About the menus
Getting started About the menus
<S: 0, 255>
<Auto/Manual>
<Standard/Alcatel/Avaya/Cisco/Microsoft/Nortel/
<S: 0, 255>
<None/Preset1/Preset2/Preset3/Preset4/Preset5/
Advanced settings Settings library
Advanced settings Settings Library Settings library
None: No action.
Preset 1..15: Activate the selected preset.
RestoreCameraPosition: Set the camera to the position it had before the last boot.
DefaultCameraPosition: Set the camera to the factory default position.
Example:
xConfiguration Standby BootAction: DefaultCameraPosition
xConfiguration Standby Control:
Determine whether the system should go into standby mode or not.
On: Enter standby mode when the Standby Delay has timed out. Requires the Standby Delay to be set to an
appropriate value.
Off: Not entering standby mode.
Example:
xConfiguration Standby Control: On
xConfiguration Standby Delay:
Define how long (in minutes) the system shall be in idle mode before it goes into standby mode. Requires the
Standby Control to be enabled.
Range: 1-480 seconds
Example:
xConfiguration Standby Delay: 10
xConfiguration Standby WakeupAction:
Preset5/Preset6/Preset7/Preset8/Preset9/Preset10/Preset11/Preset12/Preset13/Preset14/
Preset15/RestoreCameraPosition/DefaultCameraPosition>
Decide what the system is going to do when leaving standby mode.
None: No action.
Preset 1..15: Activate the selected preset.
RestoreCameraPosition: Set the camera to the position it had before entering standby.
DefaultCameraPosition: Set the camera to the factory default position.
Example:
xConfiguration Standby WakeupAction: RestoreCameraPosition
xConfiguration SystemUnit CallLogging Mode:
Enables/disables logging of calls received or placed by the system. The call logs may then be viewed via the
GUI or using the xHistory command.
On: Enable logging.
Off: Disable logging.
Example:
xConfiguration SystemUnit CallLogging Mode: On
xConfiguration SystemUnit IrSensor Mode:
The System Unit IR Sensor setting determines whether the infrared receiver on the codec should be enabled
or not. The IR sensor LED is located in the front of the codec and flickers when an ir signal is received from
the remote control.
Administrator Guide
Cameras Appendices
Cameras Appendices
<On/Off>
<1..480>
<None/Preset1/Preset2/Preset3/Preset4/
{#{#On/Off>
<On/Off/Auto>
Contact us
Contact us
32