Schwinn MPower Console V2 + Power Owner's Manual
  1. Manuals
  2. Brands
  3. Schwinn Manuals
  4. Fitness Electronics
  5. MPower Console V2
  6. Owner's manual
Schwinn MPower Console V2 + Power Owner's Manual

Schwinn MPower Console V2 + Power Owner's Manual

Hide thumbs Also See for MPower Console V2 + Power:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for Schwinn MPower Console V2 + Power

Summary of Contents for Schwinn MPower Console V2 + Power

  • Page 2: Specifications

    Specifications ensor Power Sensor Power Requirements 5.25” (13.34 cm) 2.38” (6.03 cm) Patent Information:...

  • Page 3: Important Safety Instructions

    Important Safety Instructions Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Before using this equipment, obey the following warnings: Read and understand the complete Owner’s Manual. Keep Owner’s Manual for future reference. Read and understand all warnings on this machine.
  • Page 6 KM / MPH (Speed) STAGE Time and Distance WATTS (Power) RPM (Cadence) KCAL (Calories) Heart Rate TOTAL Time and Distance Note: If you need to change the measurement units to English Imperial or metric, refer to the User Setup section of this manual. The Speed display field shows the estimated speed of the bike in kilometers per hour (KM/H) or miles per hour (MPH).

  • Page 7: Battery Level

    Workout Totals The TOTAL display field shows the total time and distance results at the end of the workout. The Total icon is lit during Workout Mode. LCD + and – Icons The + and – (plus and minus) icons on the LCD flash to prompt the user to enter their weight during User Setup Mode. The icons turn off when not in use.
  • Page 8 Errors Error messages tell you when there is a problem in the bike's operation:...

  • Page 9: Sleep Mode

    When the Cadence decreases to less than 5 RPM for 3 seconds or more, the console pauses and the LCD Display shows the last workout data values. If you stay paused for more than 5 minutes, the workout stops and the console goes to Display Results mode. To set the STAGE time and STAGE distance back to zero for a new stage in the workout, tap the STAGE button.

  • Page 10: Workout Mode

    For bikes that do not have a Power Sensor installed, user weight data is necessary to calculate the Calories during the workout. If the console does not get the weight data from a device, you must manually set the weight value. The + and – icons on the LCD flash, and the RPM field displays 170 lbs.

  • Page 11: Display Results

    Display Results Device Pairing 2. Push the STAGE and AVG/END buttons for 5 seconds to go to Service Mode. 3. Tap the AVG/END button until you see the Power menu option, and push the Backlight button. 4. Push the STAGE or AVG/END button to see the Power submenu options—Sport (not power enabled) and Perform (power enabled). •...
  • Page 12 12. Install the console and sensors on the bike. Refer to the MPower™ installation guides. Device Pairing for Multiple Bikes For Schwinn A.C.™ bikes with MPower™ Consoles in a group setting, make sure to set up Device Pairing for only one bike at a time to prevent crosstalk between the devices on different bikes.

  • Page 15: Battery Status Icon

    When you select the submenu option for a specific battery (AP1, AP2, or AP3), the console shows the level of that battery. Battery Status Icon Console Speed Sensor Power Sensor Voltage 4 segments 1.5V or more 80–100% 80–100% 3 segments 60–80% 60–80% 1.3–1.499V...

  • Page 16: Error History

    Error History Error Message Error Sequence Error Count If the battery level is low, refer to the instructions for battery replacement in this manual. System Error Message: The error message shows as "Exx". If there is no error (current operation is completed correctly), the display shows as "--". Error Count: Number of times that error occurred.
  • Page 17 Backlight Allows changes to Backlight functions. Timer: Sets the operation so that you must push the Backlight button to turn on the backlight. The length of time the backlight stays on can be adjusted. Sets the operation so that the backlight comes on and stays on when the console is on.
  • Page 18 IC Class Setup Note:...

  • Page 19: Maintenance

    Maintenance Important: Replacing the Console Batteries...
  • Page 20 Replacing the Speed Sensor Battery...
  • Page 21 Replacing the Power Sensor Battery...

  • Page 22: Troubleshooting

    Troubleshooting Condition/Problem Check Solution Note: Error Condition/Problem Solution Code...
  • Page 23 Power Sensor did not pair with Speed Sensor correctly. Push the pairing button on the back of the Console, (This error only occurs after Device Pairing was not Speed Sensor and Power Sensor (if applicable) and try completed satisfactorily.) the Device Pairing procedure again. Replace all batteries, and try the Device Pairing procedure again.
  • Page 24 Contacts NORTH AMERICA CUSTOMER SERVICE Tel: 888-678-2476 E-mail: services@stairmaster.com CORPORATE HEADQUARTERS StairMaster World Headquarters 4400 NE 77th Ave, Suite 300 Vancouver, WA, USA 98662 Tel: 888-678-2476...

Table of Contents