Related Manuals for Jet PDS-12CS
Summary of Contents for Jet PDS-12CS
- Page 1 OWNER'S MANUAL PDS-12CS 12” Disc Sander POWERMATIC WMH Tool Group www.powermatic.com 427 Sanford Rd. LaVergne, TN 37086 e-mail powermatic@wmhtoolgroup.com Phone: 253-351-6000 Fax: 1-800-274-6840 M-1791201K 06/02...
-
Page 2: More Information
This manual has been prepared for the owner and operators of a PDS-12CS Sander. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. -
Page 3: Warnings
Always keep guards in place and in proper operating condition. Do not operate the machine This disc sander is intended to be used with wood and wood products only. Use of this disc sander and a dust collector with metal products is a potential fire hazard. Support the workpiece adequately at all times during operation;... - Page 4 ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position before plugging in. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by POWERMATIC may cause hazards or risk of injury to persons. NEVER STAND ON A MACHINE.
-
Page 5: Grounding Instructions
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. -
Page 6: 230V Operation
230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This POWERMATIC sander is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. -
Page 7: Table Of Contents
Specifications PDS-12CS Stock Number... 1791201K Disc Diameter...12” Table Tilt ... 15 Up - 45 Down Dust Chute Diameter ...4” Disc Table ...16-3/8" W x 9-3/4” D Motor... 1-1/2 HP, 115/230V, 60Hz, 1Ph Impeller ...10” Overall Dimensions ...27-3/4” W x 25" D x 42-5/8” H Net Weight (approx.) ...189 Lbs. -
Page 8: Contents Of The Shipping Carton
Contents of the Shipping Carton PDS-12CS 12” Disc Sander 1. Sander 1. Sanding Disc 1. Table 1. Miter Gauge 1. Miter Gauge Fence 1. Owner's Manual 1. Warranty Card Hardware Kit 4. Hex Head Bolt M10x35 4. Flat Washer M10 4. -
Page 9: Stand Assembly
Stand Assembly 1. With the help of another person lift the sander (A, Fig. 1) onto the stand (B, Fig. 1). Feed the belt (C, Fig. 1) through the cut out in the top of the stand. 2. Match the hole pattern in the stand with the hole pattern in the sander. -
Page 10: Collector Bag Assembly
Collector Bag Assembly 1. Mount the inlet port (A, Fig. 4) to the cabinet with four M6x12 pan head screws (B, Fig. 4). 2. Thread two M6 nuts (C, Fig. 4) on the shaft of hanger rods (D, Fig. 4). Thread rods into the cabinet and tighten nuts against the cabinet. -
Page 11: Sanding Disc Replacement
Failure to comply may result in The PDS-12CS disc sander is rated 115V/230V, Prewired 115V. If you want to run the PDS-12CS on 230V refer to the wiring diagram found on the inside of the switch box cover (I, Fig. 8). -
Page 12: Emptying Collector Bag
Emptying the Collector Bag CAUTION Wearing a particle mask/respirator for protection against fine dust particles during cleaning is highly recommended. During first use and after cleaning, the bag may allow some dust to escape. This is normal and will stop after a short period of time. Clean the collector bag frequently to keep the collector's performance at its optimum. -
Page 13: Parts Breakdowns & Parts List
Base Assembly Breakdown... - Page 14 36 ...TS-1540041 ... Hex Nut ...M6 ... 2 37 ...612085... Collector Bag..1 38 ...150527... Sponge..2 39 ...620015... Washer...M10 x 20... 1 40 ...TS-1551071 ... Lock Washer ...M10... 1 Parts List for the PDS-12CS Base Assembly Description Size...
- Page 15 Sander Assembly Breakdown...
- Page 16 36 ...612084... Front Cover ..1 37 ...SF069200 ... Pan Head Flange Bolt...M6 x 8... 2 38 ...150031... Pin..3 39 ...612035... Stop Bracket..1 40 ...TS-1550061 ... Flat Washer...M8 x 18... 1 Parts List for PDS-12CS Sander Assembly Size...
- Page 17 Index Part Description 41 ...TS-1551061 ... Lock Washer ...M8 ... 1 42 ...TS-1490041 ... Cap Screw...M8 x 25... 1 43 ...612010... Locating Block ..1 44 ...TS-1540041 ... Nut ...M6 ... 1 45 ...TS-1523071 ... Set Screw...M6 x 25... 1 46 ...PS052500 ...
-
Page 18: Wiring Diagram
Wiring Diagram...