Jet JBOS-5 Operating Instructions Manual
Benchtop oscillating spindle sander
Hide thumbs
Also See for JBOS-5:
- Owner's manual (12 pages) ,
- Operating instructions manual (14 pages) ,
- Operating instructions and parts manual (16 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for Jet JBOS-5
Summary of Contents for Jet JBOS-5
- Page 1 Operating Instructions and Parts Manual Benchtop Oscillating Spindle Sander Model JBOS-5 For models with serial no. 11095097 and higher 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-708404 Ph.: 800-274-6848 Revision D1 10/2018 www.jettools.com Copyright © 2017 JET...
-
Page 2: Warranty And Service
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason ®... -
Page 3: Table Of Contents
Changing Sanding Sleeves ..........................8 Insert Plate Diameters ............................9 Optional Accessories (purchased separately) ..................... 10 Replacement Parts .............................. 10 Table Assembly for the JBOS-5 ........................11 Base and Motor Assembly for the JBOS-5 ...................... 12 Parts List for the JBOS-5 ..........................13... -
Page 4: Warning
Warning Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this tool until proper training and knowledge have been obtained. Keep guards in place and in working order. Keep fingers and hands away from the spindle while in operation. Avoid getting fingers too close to the drum. -
Page 5: Specifications
If there are any questions or comments, please contact either your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Unpacking And Setup
Finish removing all contents from the shipping container, and compare items with the list above. Contact your distributor or JET if any parts are missing. Do not discard any shipping material until the sander is set up and running properly. -
Page 7: Insert Plates
Dust Collection The dust port (B, Figure 5) can be hooked directly to a 2” hose for dust collection. See your local JET distributor for the complete line of dust collectors, as well as Hoses and Accessories. Customize your installation and obtain maximum performance with JET dust hoods, hoses, clamps, fittings, and blast gates. -
Page 8: Turning The Sander On & Off
Turning the Sander On & Off Note: Before hooking the sander to the power source, make sure the switch is in off position. The sander can be turned on by flipping the switch to the on position. There is a removable key in the tip of the switch that can be removed in the off position. -
Page 9: Insert Plate Diameters
Insert Plate Diameters This will assist you in determining which spindle diameters will work in each insert plate. -
Page 10: Optional Accessories (Purchased Separately)
Number of your machine available when you call will allow us to serve you quickly and accurately. Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET. Some parts are shown for reference only, and may not be available individually. -
Page 11: Table Assembly For The Jbos-5
Table Assembly for the JBOS-5... -
Page 12: Base And Motor Assembly For The Jbos-5
Base and Motor Assembly for the JBOS-5... -
Page 13: Parts List For The Jbos-5
53 ....JBOS5-53 ....Support Trunnion-Right ................. 1 54 ....JBOS5-54 ....Support Trunnion-Left ..................1 55 ....JBOS5-55 ....JET Lock Knob ............M6x15 ......2 56 ....JBOS5-56 ....Hex Socket Cap Screw ..........M5x15 ......6 57 .... - Page 14 ....6286982 ....Round Table Insert (for 1/4" to 1” spindles),not shown ........1 92 ....JBOS5-92 ....Oil Cap ......................1 93 ....JBOS5-93 ....JET Label....................... 1 94 ....JBOS5-94 ....Warning Label ....................1 95 ....
- Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com...