Agria 400E Operating Instructions Manual

Agria 400E Operating Instructions Manual

Multi-purpose machine

Advertisement

Original
Original
Original
Original
Original
Operating
Operating
Operating
Operating
Operating
Instructions
Instructions
Instructions
Instructions
Instructions
Multi-Purpose Machine
Multi-Purpose Machine
Multi-Purpose Machine
Multi-Purpose Machine
Multi-Purpose Machine
400E and 400K
400E and 400K
400E and 400K
400E and 400K
400E and 400K
Briggs&Stratton engine
3348, 5117, 3346
Before commissioning the machine, read operating
instructions and observe warnings and safety instructions.
Operating Instructions No. 998 702-C 01.10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 400E and is the answer not in the manual?

Questions and answers

Summary of Contents for Agria 400E

  • Page 1 Instructions Instructions Instructions Multi-Purpose Machine Multi-Purpose Machine Multi-Purpose Machine Multi-Purpose Machine Multi-Purpose Machine 400E and 400K 400E and 400K 400E and 400K 400E and 400K 400E and 400K Briggs&Stratton engine 3348, 5117, 3346 Before commissioning the machine, read operating instructions and observe warnings and safety instructions.
  • Page 2: Amount Of Delivery

    Amount of delivery: Operating instructions Open (unlocked) Grassland mower – basic machine Closed (locked) Steering handle with grip screw Tool kit version 400K additionally: Starter battery with battery acid - Service = contact Your agria workshop agria Multi-Purpose Machine 400E/400K...
  • Page 3 Designation of Parts Type 400E Version Version Briggs & Stratton 5 HP Briggs & Stratton Power Built 190 135 202 110 412 agria Multi-Purpose Machine 400E/400K...
  • Page 4 7 Starter handle 8 Cooling air-screen 9 Exhaust with guard 10 Spark plug/spark plug connector 11 Engine oil filler plug and control opening 12 Engine oil drain plug 13 Fuel tap (only version Power Built 190) agria Multi-Purpose Machine 400E/400K...
  • Page 5: Table Of Contents

    Working ........... 44 Danger zone ........44 Instructions for Unpacking and Assembly ........9 5. Maintenance Engine 400E / 400K ....45 / 46 Recommendations Air filter ..........47 Lubricants, Anti-Corrosive Agents .. 10 Fuel system ........47 Fuel ..........10 Cooling system .......
  • Page 6 Multi-Purpose Machine 400E/400K...
  • Page 7: Designation Of Parts

    Designation of Parts Type 400K agria Multi-Purpose Machine 400E/400K...
  • Page 8 6 Engine type no. 7 Starter handle 8 Cooling air-screen 9 Exhaust with guard 10 Spark plug/spark plug connector 11 Engine oil filler plug and dip-stick 12 Engine oil drain plug 13 Electric starter 14 Battery agria Multi-Purpose Machine 400E/400K...
  • Page 9: Instructions For Unpacking And Assembly

    4 Battery cable 5 Battery holder The battery operation and its maintenance and 6 Tensioning spring care must be made in line with the battery 7 Protective hose manufacturer's operating instructions on page 33. 8 Connecting cap agria Multi-Purpose Machine 400E/400K...
  • Page 10: Recommendations

    Only use suitable This engine runs smoothly on conven- tools to pull off the flywheel. tional unleaded regular supergrade petrol as well as on leaded supergrade petrol. Do not add oil to petrol. agria Multi-Purpose Machine 400E/400K...
  • Page 11: Safety Instructions

    Careful with rotating tools - keep at a Any unauthorized changes to the ma- safe distance! chine render manufacturer liability null Foreign powered parts shear and crush! and void. Riding on the attachment during opera- tion is not permitted. agria Multi-Purpose Machine 400E/400K...
  • Page 12 Ensure that all guards in place. Have the malfunction removed without With no attachment mounted, make delay. To prevent the machine from sliding on agria Multi-Purpose Machine 400E/400K...
  • Page 13 Couple the attachments as specified and only couple at specified points. Secure the machine and attachment against unauthorized use and rolling off when you leave the machine. If neces- sary, install transport or safety devices to provide protection. agria Multi-Purpose Machine 400E/400K...
  • Page 14 Fuel vapours are ger of burns. hazardous. Make sure oil used is of specified qual- ity. Storage is in approved cans only. Dispose of oil, greases, and filters seperately and properly. agria Multi-Purpose Machine 400E/400K...
  • Page 15: Safety Instructions

    Always cover positive terminal with the specified cover or terminal cap. Wear protective gloves. Persons having a pacemaker may not touch live parts of the ignition system Wear solid shoes. when the engine is running. agria Multi-Purpose Machine 400E/400K...
  • Page 16: Specifications

    ..3.50 - 6 und 4.00 - 8 (Field tyre) speed with tool at work. Tyre pressure: ......1.0 bar Speed Revolutions [rpm Ground speed [km/h] Wheel shaft Pto Tyres 13x5.00-6 3.50-6 4.00-8 67.5 1650 42.7 3310 61.7 1740 agria Multi-Purpose Machine 400E/400K...
  • Page 17: Engine, Ausf 400E / 400K

    Filling quantity ....approx. 0.6 l ance is satisfactory (engine oil level at Multi-grade oil SAE 10 W-40 API-SC, “max” = upper filling mark). SF or higher agria Multi-Purpose Machine 400E/400K...
  • Page 18 ..3.50 - 6 und 4.00 - 8 (Field tyre) speed with tool at work. Tyre pressure: ......1.0 bar Speed Revolutions [rpm Ground speed [km/h] Wheel shaft Pto Tyres 13x5.00-6 3.50-6 4.00-8 67.5 1650 42.7 2550 28.1 3750 10.1 61.7 1740 agria Multi-Purpose Machine 400E/400K...
  • Page 19 As long as the operator is able to walk and drive the power mower on slopes Starter: ....Electric starter 12 V without problems, the engine perform- Recoil starter (manual starter) ance is satisfactory (engine oil level at “max” = upper filling mark). agria Multi-Purpose Machine 400E/400K...
  • Page 20: Devices And Operating Elements

    High engine speed is harmful to any engine and consider- ably affects its durability. This applies especially for no load operation. Any overspeed (have the engine roar) can result in immediate damage. agria Multi-Purpose Machine 400E/400K...
  • Page 21: Speed Control Lever

    (E/3 or G/3). Do not fasten the safety lever. The safety lever also serves to switch off in an emergency. Release the safety lever for fast engine switch-off. The lever automatically goes to STOP position. agria Multi-Purpose Machine 400E/400K...
  • Page 22: Choke, Fuel Tap

    To avoid clutch slipping away during operation, a clutch play is factory-set at the hand lever (refer to “Maintenance”). After the first operating hour, the clutch play has to be checked and, if necessary, re-adjusted (refer to “Maintenance”). agria Multi-Purpose Machine 400E/400K...
  • Page 23 Replace V-belt guide plate (F/7 or H/7). Push the guard (F/5 or H/5) onto pins (F/4 or H/4) and close. Fit nut (F/10 or H/10) with spring washer (F/9 or H/9) and tighten. Only drive pto-driven attachments at speed “I”. agria Multi-Purpose Machine 400E/400K...
  • Page 24 3. Devices and Operating Elements Type 400E Type 400K Figure: V-belt is in “speed I” position. Figure: V-belt is in “speed I” position. Recommended speeds Type 400E I : Pto-driven rotary snow cleaner, attachments mowing, sweeping, spreading, On the V-belt guard to the left there is a...
  • Page 25 Move hand lever for wheel drive (E/ 11 or G/11) down. Slowly release the hand clutch lever (E/4 or G/4) while pressing the throttle. In case wheel drive cannot be engaged, couple and decouple. Then engage wheel drive. agria Multi-Purpose Machine 400E/400K...
  • Page 26: Drive-Wheels

    Let detent spring engage in a ring groove again (fig. K and L). Brush Bio-lubricating grease onto both ends of wheel-shaft (small diam- eter of wheel-shaft). For dismounting drive-wheels, proceed 1 Detent spring accordingly but in reverse order. agria Multi-Purpose Machine 400E/400K...
  • Page 27 (fig. L). Drive with differential effect: En- gage one drive-wheel into inner ring groove (fig. K), engage the second drive- wheel into outer ring groove (fig. L) – neutral. agria Multi-Purpose Machine 400E/400K...
  • Page 28 Cage Drive-Wheels Dismount drive-wheels. Mount cage drive-wheels onto wheel- shaft (as described in “Mounting Drive- Wheels”). Rigid drive, neutral, drive with differential effect can also be engaged with twin and cage drive- wheels mounted. agria Multi-Purpose Machine 400E/400K...
  • Page 29 To remove the drive-wheels reverse the 1 Wheel shaft above process. 2 Differential hub 3 Star washer 4 Hex bolt 5 Wheel drive 6 Ball spring washer 7 Wheel bolt To remove the drive-wheels reverse the above process. agria Multi-Purpose Machine 400E/400K...
  • Page 30 (Item no. 0421 011). Fitting wheel weights To fit wheel weights (2) onto the wheel flange, use hex bolts(4) and star wash- ers. (Torque 80 Nm) 1 Drive-wheel 2 Wheel weight 3 Washer 4 Hex bolt agria Multi-Purpose Machine 400E/400K...
  • Page 31: Pto

    Take the force off and move the stand further down until it locks. To fold the stand up, reverse the above proc- ess. Note: Before you take up operation, fold up the stand. agria Multi-Purpose Machine 400E/400K...
  • Page 32: Steering Handle

    Steering handle side adjustment Loosen hex bolt (1) or grip screw (1) until all notches are free. Swivel the steering handle to the desired position and fit into proper notch. Re-tighten hex bolt or grip screw. agria Multi-Purpose Machine 400E/400K...
  • Page 33: Battery

    - threat of an explosion! Avoid short circuits. Careful when handling battery acid – etching! The battery contains poisonous substances and heavy metals and constitutes hazardous waste. agria Multi-Purpose Machine 400E/400K...
  • Page 34: Attachments

    Cap Bring tensioning bands into starting position: 1. Move both tensioning levers (a) to the rear, 2. pull both tensioning bands (b) towards the side while you 3. move both tensioning levers back to the front. agria Multi-Purpose Machine 400E/400K...
  • Page 35 Fit the cap onto the pto shaft of the ba- sic machine. Warning! Only drive pto-driven attach- ments at speed “I” (slow). Only operate attachments only with all guards in place. Observe the operating instructions of the respective attachments! agria Multi-Purpose Machine 400E/400K...
  • Page 36 (6 and 7) . In this way the steering pat- tern may be individually adjusted for 1 Hitching device each attachment. (optional 0440 021) 2 Connecting collar 3 Connecting pin 4 Spring clip 5 Crank agria Multi-Purpose Machine 400E/400K...
  • Page 37 (3). Removing the weight support 1 Weight support 2 Weight When removing the weight support, the 3 Clamping bolt weight can stay mounted on it. To re- move the weight support, open the quick tensioning device. agria Multi-Purpose Machine 400E/400K...
  • Page 38: Hoeing, Ridging

    Fasten with linch pin (2) through blades on the other side of the case. hub/shaft borings. Bolt down sets of blades with hex bolts (7) through the borings of the hub/rotor shaft. agria Multi-Purpose Machine 400E/400K...
  • Page 39 5 Depth bar 10 Coupling unit 11 Linch pin 12 W-clip 13 Lock nut 14 Set screw 15 Pin 17 Wheel depth bar mounting unit 18 U-pin 20 W-clip 21 Clamp screw for ridger 22 Clamp screw agria Multi-Purpose Machine 400E/400K...
  • Page 40 6 Clamp screw for adjusting ridging width 7 Mouldboard 8 Blade 9 Fastening screw for blades 10 Blade 11 Set screw for swinging buffer 12 Pin 13 Linkage 14 Clamp screw for slade 15 Slade 16 Strake wheels agria Multi-Purpose Machine 400E/400K...
  • Page 41: Commissioning And Operation

    To avoid starting problems, top up fuel Do not step near the coupled at- before starting for the first time and af- tachment. ter longer storage. agria Multi-Purpose Machine 400E/400K...
  • Page 42: Starting The Engine

    - start from a position outside the hazardous area! Electric start - only version 400K Press the start button (G/8). - Electric starter is turning. As soon as the motor is started, release the start button. CHOKE to operation position. agria Multi-Purpose Machine 400E/400K...
  • Page 43: Switching Off The Engine

    Do not move the choke lever to CHOKE position to shut off the engine – danger of fire! The speed control lever also serves as emergency off-switch. If necessary, move the speed control lever to position “STOP” to cut out the engine. agria Multi-Purpose Machine 400E/400K...
  • Page 44: Working

    Pull hand clutch lever all the way up and press the trottle at the same time. If cleaning becomes neces- sary during operation, cut out the engine and remove spark plug con- nector for safety reasons. agria Multi-Purpose Machine 400E/400K...
  • Page 45: Maintenance

    If possible, use a funnel or similar de- fill! vice to fill in oil. Re-tighten oil filler plug. Re-tighten oil filler plug. Only change oil while engine is still warm, but not hot – danger of burns! agria Multi-Purpose Machine 400E/400K...
  • Page 46 If possible, use a funnel or similar de- Re-tighten oil filler plug. vice to fill in oil. Re-tighten oil filler plug. Only change oil while engine is still warm, but not hot – danger of burns! agria Multi-Purpose Machine 400E/400K...
  • Page 47: Air Filter

    Version Power Built engine til engine starts. see separate Briggs & Stratton engine Do not crank engine when spark plug is operating instructions removed. agria Multi-Purpose Machine 400E/400K...
  • Page 48: Cooling System

    0,75 mm carburetor B/2 or D/2). Exhaust Regularly clean the surrounding parts of the muffler (B/9 or D/9) from grass, dirt and inflammable deposits. - Danger of fire! Check each time before you take up operation. agria Multi-Purpose Machine 400E/400K...
  • Page 49: Speed Control

    – danger of fire! fitted. Avoid short circuits. - Service The battery contains poisonous substances and heavy metals and constitutes hazardous waste. agria Multi-Purpose Machine 400E/400K...
  • Page 50: Machine

    Constantly check wheel-shaft for wound-on grass, remove the grass by taking off the drive-wheels, if necessary. Lubricate the wheel-shaft ends with Bio-lubricating grease (small shaft diam- eter) each time before you mount the drive-wheels, once a year, and after clean- ing with a pressure washer. agria Multi-Purpose Machine 400E/400K...
  • Page 51: Safety Circuit

    Fit retaining spring (2). Hand lever for wheel drive: X = 3 - 5 mm Hand lever for clutch: X = 2,5 - 4 mm However, the basic setting is adjusted in neutral position.(see “Adjusting V-Belt Tension”). agria Multi-Purpose Machine 400E/400K...
  • Page 52 Mount pulley and belt guard (F/8 or Only operate attachments H/8). For this purpose, the clutch lever with all guards in place. must be in position “forward”. Do not use conventional V-belts but only agria special belts. agria Multi-Purpose Machine 400E/400K...
  • Page 53: General

    Engine Clean the engine only with a cloth. Avoid spraying with strong water jets, as wa- ter might leak into the ignition and fuel system, causing malfunctions. agria Multi-Purpose Machine 400E/400K...
  • Page 54: Storage

    - in humid rooms - in rooms where fertilizer is stored - in stables or adjacent rooms. g) Covering the machine Protect the machine with cloth or a simi- lar cover. agria Multi-Purpose Machine 400E/400K...
  • Page 55 Multi-Purpose Machine 400E/400K...
  • Page 56: Troubleshooting

    - Speed control linkages Clean speed control linkages does not run clogged or jammed smoothly Engine - Speed control and engine stop Adjust speed control does not stop are not adjusted properly when set to stop agria Multi-Purpose Machine 400E/400K...
  • Page 57 Travelling drive - Incorrect hand clutch lever adjustment Adjust hand clutch lever or mowing drive does not stop with clutch pulled Excessive - Fastening screws loosened Tighten fastening screws vibration = For this purpose contact your agria workshop. agria Multi-Purpose Machine 400E/400K...
  • Page 58: Electric Wiring Diagram

    4 Connector pair 5 Switch in safety lever 6 Switch in clutch lever bl = blue br = brown Lubrication chart Engine oil (page 45/46) Transmission oil (page 50) Lever bearing (page 53) agria Multi-Purpose Machine 400E/400K...
  • Page 59: Varnishes, Wear Parts

    V-belt for clutch 481 74 V-belt for reverse drive 305 65 Gasket for housing cap (oil change) Note: Only use original agria V-belts! Spare Parts 997 086 All-purpose machine 400E, 400K and attachments 771 83 Suction pump agria Multi-Purpose Machine 400E/400K...
  • Page 60 Multi-Purpose Machine 400E/400K...
  • Page 61 5 Borings for threaded pins 6 V-belt pulley (on crank shaft) 7 Belt guide plate 8 Belt guard 9 Spring washer 10 Lock nut 11 Reverse rubber pulley 12 Drive V-belt for reverse speed 13 V-belt pulley (on drive shaft) agria Multi-Purpose Machine 400E/400K...
  • Page 62 Designation of Parts Type 400E agria Multi-Purpose Machine 400E/400K...
  • Page 63 Multi-Purpose Machine 400E/400K...
  • Page 64: Inspection And Maintenance Sheet

    E = Nonrecurrent maintenance to be executed by professional workshop K = Checks and maintenance to be executed by operator W = Maintenance to be executed by professional workshop F = Maintenance should be carried out by your agria workshop * = after 2 years agria Multi-Purpose Machine 400E/400K...
  • Page 65 5 Borings for threaded pins 6 V-belt pulley (on crank shaft) 7 Belt guide plate 8 Belt guard 9 Spring washer 10 Lock nut 11 Reverse rubber pulley 12 Drive V-belt for reverse speed 13 V-belt pulley (on drive shaft) agria Multi-Purpose Machine 400E/400K...
  • Page 66 Designation of Parts Type 400K agria Multi-Purpose Machine 400E/400K...
  • Page 67: Conformity Declaration

    EC Declaration Conformity agria Multi-Purpose Machine 400E/400K...
  • Page 68 agria-Werke GmbH Bittelbronner Straße 42 D-74219 Möckmühl Tel. +49/ (0)6298 /39-0 Fax +49/ (0)6298/39-111 e-mail: info@agria.de Internet: www.agria.de Your local agria specialist dealer:...

This manual is also suitable for:

400k

Table of Contents