Page 1
Horticultural Machinery Horticultural Machinery Horticultural Machinery Horticultural Machinery Horticultural Machinery Operating Instructions ® for agria Power Hoe Type 6000 & Before commissioning the machine, read operating instructions and observe warnings and safety instructions. Operating Instructions No. 998 720 11.98...
Page 2
For engine type and number, refer to p5/item no. 27. Please state these data when ordering spare parts to avoid wrong deliveries. Only use original agria spare parts! Specifications, figures and dimensions Hoeing/tilling drive stated in these instructions are not bind- ing.
Maintenance and Using ecologically safe Bio-lubricants Repair: and Bio-anti-corrosives, you contribute to environmental protection and to the The trained mechanics of your agria wellbeing of humans, animals and plants. workshop expertly carry out any main- tenance and repair work. Fuel...
4 Locking plate on joint l Steering handle removal is in re- 5 Hex head bolt verse order. l To start up, carry out all steps de- scribed on page 23. Edition 11.98 Power Hoe 6000...
Compliance is for your own safety. When transporting the power hoe on vehicles or trailers outside the area to be cultivated, ensure that the engine is turned off. Careful with rotating tools – keep at a safe distance! Power Hoe 6000 Edition 11.98...
For operation in enclosed areas, ensure steering handle while power hoe is at that a safety distance is kept to enclo- work. sures to prevent damage to tools. Never adjust the steering handles during work – danger! Edition 11.98 Power Hoe 6000...
Page 10
Never leave the power hoe unattended adjusted properly. with the engine running. Before you leave the power hoe, turn off the engine. Then close fuel tap. Secure power hoe against unauthorized use – remove spark plug connector. Power Hoe 6000 Edition 11.98...
Page 11
Make sure fuel is of specified quality. Only use original agria spare parts. All Store fuel in approved cans only. other commercial spare parts must cor- Store anti-corrosive agents and stabiliz- respond to quality and technical require- ing liquids out of reach of children.
Do not work without protective covers Electrical System and mounted. Before starting the engine, bring covers into proper position. Battery Persons having a pacemaker may not touch live parts of the ignition system when the engine is running. Power Hoe 6000 Edition 11.98...
Starter: ......Recoil starter Operability on Slopes: Stop device: ....Contact break Engine is suited for use on slopes: via short circuit cable continuous operation possible Engine-stop-switch on handlebar up to ....45° inclination (100%) Power Hoe 6000 Edition 11.98...
3. Devices and Operating Elements The power hoe agria 6000 is suited for Cooling System common horticultural, agricultural, and The engine is fan-cooled. Therefore keep forestal operations, and for grass and screen at recoil starter and cooling ribs park maintenance.
(refer to “Maintenance”). Start position l Stop position: Upon release of the lever, the ignition system is switched off (engine is off). Beware – engine keeps running due to centrifugal mass. Power Hoe 6000 Edition 11.98...
(A/18). 1 Coupling unit 2 Adapter tube 3 Locking pin 1 Locking pin 4 R-clip 2 R-clip 5 Crank Ensure the pin is locked in place with the R-clip (2) after the implement is attached. Edition 11.98 Power Hoe 6000...
Attach wheel hubs (2) to both ends of the hoeing shaft. l Guide the anchoring bolt (1) through the hubs and the shaft as shown in the illustration. l Attach locking nut (3) and tighten it (100Nm). Power Hoe 6000 Edition 11.98...
Wheel-Weights wheeling for forward operation l Backward position= Drive and free- Wheel weights are available to improve wheeling for reverse operation traction. Wheel weight ... Item no. 3221 011 to be fitted to drive-wheels 5.0-10 Edition 11.98 Power Hoe 6000...
Loosen grip screw (3) until the notches on the beam are released. l Fold the beam up into a mesh with the notches and tighten the grip screw. Transport position l Fold the support wheel down and tighten the grip screw. Power Hoe 6000 Edition 11.98...
4 Tensioning bolt Hoeing leg settings A = in heavy soil B = in medium to light soil C = in sandy soil The share (4) is for working in losened soil only. Power Hoe 6000 Edition 11.98...
Do not spill any fuel, use a proper l Do not touch the ignition cable and filling device. do touch or remove ignition spark connector while the engine is running. Edition 11.98 Power Hoe 6000...
After the start, let rope glide back. Do not let snap. l Once the engine has started, slowly move speed control lever to centre posi- tion and let engine warm up for some time. Power Hoe 6000 Edition 11.98...
This ensures that carburetor is empty and no resin residue can deposit. Secure power hoe against unauthorized use – discon- nect spark-plug connector. Edition 11.98 Power Hoe 6000...
Turn off the engine. and clean the attachment with an ap- l Pull hand clutch lever. propriate tool (wooden stick). l Turn off hoeing drive (B/19) (position “0”). l If present, fold front support wheel into travel direction. Power Hoe 6000 Edition 11.98...
Clean air filter and outside surround- air circulation. For this purpose, contact ing parts. your professional agria workshop. l Open closing bow and remove oil pot. l Remove old oil (dispose of properly) Cleaning Spark Plug and and clean oil pot.
(also refer to until engine starts. Or remove spark plug “Specifications”). For these adjust- and clean and dry. With spark plug ments, contact your professional agria removed, crank engine a few times with workshop. recoil starter. Screw spark plug back in and re-start engine.
(3). For oil filling quantity and quality, see l Set the chain tension via the hex head ”Specifications”. bolt (2). l Retighten locking nut (3) and attach- ment nuts (1). 3 Drain plug 4 O-ring Edition 11.98 Power Hoe 6000...
For inspection, hook the cable end back into the bracket, using the set pin. l Fit retaining spring (2). Clutch lever: X = 3–5 mm (Clutch play) Power Hoe 6000 Edition 11.98...
Inspect all electric lines and connec- (e.g. speed control lever, hand lever tions and replace them if necessary. bearing, etc.) slightly with Bio-lubrication grease and Bio-lubrication oil. For this purpose contact your agria workshop. Cleaning After each cleaning (washing with water, Stop position...
Drain fuel completely and let the en- Protect machine with cloth or a similar gine run until it comes to stop due to lack cover. of fuel or add fuel stabilizer (agria No. 673 50). Method: Fill fuel tank, add anti-corrosive and stabilizing liquid (amount “ON”...
Chain housing seal – top, internal 256 45 Chain housing seal top, external 172 22 Hoeing tine, left right left 172 23 Hoeing tine, right Spare Parts 997 127 Power Hoe 6000 997 050 agria Engine Edition 11.98 Power Hoe 6000...
B = After each cleaning K = Checks and maintenance to be executed by operator W = Maintenance to be executed by professional workshop F = Maintenance should be carried out by your agria workshop * = after 2 years Power Hoe 6000...
7 Pawl 8 Speed control lever Electrical Wiring Diagram 1 Engine 2 Magnet ignition system 3 Engine speed delimiter 4 Switch in dead stop lever 5 Switch in clutch lever bl = blue br = brown Edition 11.98 Power Hoe 6000...
Page 38
Designation of Parts Power Hoe 6000 Edition 11.98...
EC directive machinery 98/37/EC agria-Werke, GmbH D-74215 Möckmühl/Württ. herewith declare in sole responsibility that the product Power Hoe, Type 6000 to which this declaration refers, corresponds to the standard fundamental safety and health requirements as stipulated in EC directive machinery 98/37/EC and EMC directive 89/336/EC.
Page 40
Phone 0049 62 98 39-0 0049 62 98 39-111 e-mail: info@agria.de Internet: http://www.agria.de The Winning Team Power hoes One-wheel hoes Hobby two-wheelers AllShredd Cutterbar mowers Lawn mowers Verticutters All-purpose machines Contact your authorised agria dealer for service and prompt delivery of spare parts...