Related Manuals for Landa HOT 2-1100
Summary of Contents for Landa HOT 2-1100
- Page 1 OPERATOR’S MANUAL ■ HOT 2-1100 ■ HOT2-1500 ■ HOT 4-2000 ■ HOT 3-1100 ■ HOT 3-300 89172080-1 For technical assistance or the Landa Dealer nearest you, consult our web page at www.landa.com 8.917-208.0...
-
Page 2: Table Of Contents
CONTENTS Introduction & Important Safety Information 4-5, 7 Component Identifi cation Installation Assembly Instructions Operating Instructions Detergents & General Cleaning Techniques Shutting Down & Clean-up Storage Maintenance & Service 12-14 Preventative Maintenance and Oil Change Record Troubleshooting 16-18 Warranty Model Number ______________________________ Serial Number ______________________________ Date of Purchase ___________________________ The model and serial numbers will be found on a decal attached... -
Page 3: Introduction & Important Safety Information 4
INTRODUCTION & IMPORTANT SAFETY INFORMATION Thank you for purchasing this Pressure Washer. DANGER: Improper connection of the equipment- grounding conductor can result in a risk of elec- We reserve the right to make changes at any time trocution. Check with a qualified electrician or without incurring any obligation. -
Page 4: Important Safety Information
IMPORTANT SAFETY INFORMATION WARNING: High pressure spray WARNING: High pressure devel- WARNING WARNING can cause paint chips or other oped by these machines will particles to become airborne cause personal injury or equip- and fl y at high speeds. To avoid ment damage. -
Page 5: Component Identifi Cation
COMPONENT IDENTIFICATION Discharge Nipple Brake Detergent Injector Stackless Top Adapter Kit Quick (Optional 8.903-430.0) Coupler Collar Burner Switch Pump Hour Meter Switch Thermostat Detergent Pick-up Tube Power Supply GFCI Brass Soap Nozzle Detergent Spray Bucket High Variable Pressure Wand (not included) Pressure 2-11024D, 2-15024D, Nozzle... -
Page 6: Introduction & Important Safety Information
They must be stored indoors when not in use. prop er power sup ply using a volt meter. The HOT 2-1100, HOT 2-1500, and HOT 3-1100 each Location: require a 115V-20 amp re cep ta cle to com ply to the The location should protect the machine from dam - UL 1776 Standard. -
Page 7: Assembly Instructions
ASSEMBLY INSTRUCTIONS Spray Discharge Nipple Detergent Injector Safety Coupler Latch High Collar Pressure High Hose 89172080-5 Pressure Hose 89172080-4 89172080-3 STEP 1: Connect the power cord STEP 2: Connect high pressure STEP 3: Attach the high pres - into the proper electrical out - hose to discharge nipple by slid - sure hose to the spray gun using let, then push in the GFCI reset... -
Page 8: Operation Instructions
OPERATION INSTRUCTIONS Pump/Burner Knob Pump Switch Burner Switch 89172080-10 89172080-11 89172080-12 STEP 1: STOP! Read opera- STEP 2: On machines with vari- STEP 3: Before installing nozzle, tor’s manual before operating this able pres sure wands, grip spray turn on water supply and run ma chine. -
Page 9: Detergents & General Cleaning Techniques
DETERGENTS & GENERAL CLEANING TECHNIQUES WARNING: Some de ter gents top to bottom in an even sweep ing mo tion keep ing WARNING the spray nozzle ap prox i mate ly 1 foot from cleaning may be harm ful if in haled or sur face. -
Page 10: Shutting Down & Clean-Up
SHUTTING DOWN AND CLEAN-UP Pump Knob Pump Switch 89172080-10 89172080-11 89172080-14 89172080-15 STEP 1: Re move deter- STEP 2: Turn pump STEP 3: After water has STEP 4: Squeeze gent suc tion tube from switch ON or turn knob cooled to less than 100°, trigger on spray gun container and insert into to pump po si tion then... -
Page 11: Maintenance & Service
Landa Deliming Powder (Landa Part #9-028008) will The areas around the Landa washer should be kept remove lime and other deposits be fore coil becomes clean and free of combustible materials, gasoline plugged. -
Page 12: Rupture Disk
Biodiesel fuels are becoming more popular as alter- spray gun, the un load er goes into a by-pass mode, native fuels under the Green Initiative. Landa en- thus stop ping elec tri cal cur rent to the fuel solenoid dores the use of fuels that are blended with biodies- coil. - Page 13 6. Dis con nect 1/2" pipe nipples from inlet and dis charge side of coil. Landa Sure Fire Oil Burner 7. Re move top tank wrap exposing in su la tion and coil and fold back in su la tion.
-
Page 14: Preventative Maintenance And Oil Change Record
At ten tion to reg u lar pre ven ta tive main te nance pro ce dures will as sist in preserving the performance of your equipment. Contact your LANDA dealer for main te nance. -
Page 15: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION LOW OPERATING Faulty pressure gauge Install new gauge. PRESSURE Insuffi cient water supply Use larger garden hose; clean fi lter washer at water inlet. Old, worn or incorrect spray nozzle Match nozzle number to machine and/or replace with new nozzle. - Page 16 Fuel fi lter partially cogged Replace as needed. Soot build up on coils Clean coils with soot remover. Lime build up in coils Clean inside of coils using Landa's coil cleaner. Improper burner nozzle See combustion assembly breakdown WATER TEMPERATURE Incoming water to machine warm Lower incoming water temperature.
-
Page 17: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION BURNER LIGHT WILL Disconnected or short in electrical All wire contacts should be clean and tight. NOT LIGHT wiring No breaks in wire. Burner motor thermal protector If tripped, check voltage, connections, and tripped extensions for cause. Check fuel pump shaft rotation for binding causing motor to over- heat. - Page 18 Authorized LANDA Dealer of the defect. Your Authorized LANDA Dealer will file a claim with Landa, who must subsequently verify the defect. In most cases, the part must be returned to LANDA freight prepaid with the claim. For warranty service on components warranted by other manufacturer’s, your Authorized LANDA Dealer can help you obtain warranty service through these manufacturers’...
- Page 19 Form #8.917-208.0 • Revised 03/12 • Printed in U.S.A.
Need help?
Do you have a question about the HOT 2-1100 and is the answer not in the manual?
Questions and answers