Page 1
Pressure Washer MODELS: HOT 2-11024D 1.109-095.0 HOT 2-15024D 1.109-096.0 HOT 2-11026D 1.109-093.0 HOT 2-15026D 1.109-094.0 HOT 3-11024D 1.109-097.0 HOT 3-30036D 1.109-100.0 HOT 4-20024A 1.109-098.0 HOT 4-20024G 1.109-99.0 For the Landa Dealer nearest you, consult our web page at www.landa.com 8.917-208.0-B 01/07/20...
Model: Date of Purchase: Serial Number: Dealer: Address: Phone Number: Sales Representative: The model and serial numbers will be found on a decal attached to the pressure washer. Landa HOT Series Operator’s Manual 8.917-208.0 - B...
2. Know how to stop the machine and bleed pressure quickly. Be thoroughly familiar with the controls. 3. Stay alert — watch what you are doing. Landa HOT Series Operator’s Manual 8.917-208.0 - B...
Page 6
HOT SURFACES peuvent causer des brûlures. CAN CAUSE BURNS This pressure washer shall be installed only in Utiliser uniquement les zones de locations where combustible dusts and flammable Landa HOT Series Operator’s Manual 8.917-208.0 - B...
Page 7
Follow the maintenance instructions death, serious bodily injury, and/or property damage. specified in the manual. Follow storage instructions specified in this manual. 16. Inlet water must be clean fresh water and no hotter then 90°F. Landa HOT Series Operator’s Manual 8.917-208.0 - B...
Installation Placement Place machine in a convenient location providing Do not locate near any combustible material. ample support, drainage and room for maintenance. Keep all flammable material at least 20 feet away. These machines are designed for indoor use. They Allow enough space for servicing the machine.
ATTENTION: Ne jamais remplacer les buses sans d'abord mettre le dispositif de sécurité sur la détente du pistolet pulvérisateur. Fuel STEP 7: Fill fuel tank with proper fuel Landa HOT Series Operator’s Manual 8.917-208.0 - B...
For hot water washing, turn the burner switch and thermostat ON or turn three position switch knob to the burner position. (The burner will light automatically.) Landa HOT Series Operator’s Manual 8.917-208.0 - B...
Models using variable pressure wands, grip spray gun securely. Turn variable pressure control handle counter- clockwise to reduce pressure and for applying soap through the brass soap nozzle with detergent injector attached. Landa HOT Series Operator’s Manual 8.917-208.0 - B...
Pre-rinse cleaning surface with fresh water. Place detergent suction tube directly into cleaning solution and apply to surface at low pressure (for best results, limit your work area to sections approximately 6 feet square and Landa HOT Series Operator’s Manual 8.917-208.0 - B...
If this develops, the engine may run rough, lose tions: power and may stall. This temporary condition can be Landa HOT Series Operator’s Manual 8.917-208.0 - B...
In areas where alkaline water is an extreme problem, periodic use of Landa Coil Descaler (Landa The areas around the Landa washer should be kept Part #8.914-296.0) will remove lime and other deposits clean and free of combustible materials, gasoline and before coil becomes plugged.
Biodiesel fuels are becoming more popular as alterna- Transformer test: (CAUTION 10,000 VOLTS) use tive fuels under the Green Initiative. Landa endores the defect free insulated screwdriver and keep fingers off use of fuels that are blended with biodiesels meeting...
10. Replace or repair any insulation found to be torn or broken. Coil Reinstallation Fuel Pump Reinstall new or cleaned coil by reversing Steps 9 through 1 above. Air Adjustment Screw Air Shutter Locking Screws Landa HOT Series Operator’s Manual 8.917-208.0 - B...
Attention to regular preventative main- tenance procedures will assist in preserving the performance of your equipment. Contact your LANDA dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer. Perform maintenance more often under severe conditions.
Repair hole. Low detergent level Add detergent, if needed. Turn variable pressure control handle to Variable pressure control handle set allow water to flow out of brass soap for high pressure nozzle. Landa HOT Series Operator’s Manual 8.917-208.0 - B...
Page 20
Replace as needed. Soot build up on coils Clean coils with soot remover. Lime build up in coils Clean inside of coils using Landa's coil cleaner. Improper burner nozzle See combustion assembly breakdown Landa HOT Series Operator’s Manual 8.917-208.0 - B...
Page 21
Short in electrical wiring breaks in wires. Coil liming up causing excessive See section on Preventative Maintenance. pressure Water pump low or out of oil causing Fill to correct level. the pump to bind up Landa HOT Series Operator’s Manual 8.917-208.0 - B...
Need help?
Do you have a question about the HOT Series and is the answer not in the manual?
Questions and answers