The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference. 8.913-943.0 • LANDA HS • Rev. 4/13...
This manual covers the operation and maintenance trocution. Check with a qualified electrician or of the HS-3000 heater module. All information in this service personnel if you are in doubt as to whether manual is based on the latest product information the outlet is properly grounded.
Keep operating area clear of all persons. 10. High pressure developed by 22. Landa will not be liable for any changes made to the attached pressure washer HOT DISCHARGE our standard machines, or any components not can cause bodily injury or dam- FLUID.
Insulated Handle 89139430-3 NOTE: The water in this machine is hot. The Hose, spray gun & wand and attached pressure wand and spray gun must be insulated washer not included on the HS-3000 8.913-943.0 • LANDA HS • Rev. 4/13...
Pull the nozzle to make sure nozzle. CAUTION: Never replace it is seated properly. nozzles without engaging the safety latch on the spray gun trigger. 8.913-943.0 • LANDA HS • Rev. 4/13...
Adjust burner air settings after stack is the amount of fuel being burned. installed Electrical: This machine, when installed, must be electri- cally grounded in accordance to local codes. Check for proper power supply using a volt meter. 8.913-943.0 • LANDA HS • Rev. 4/13...
To apply soap read operator's manual. NOTE: High pressure hose, nozzles, gun and wand are included with attached pressure washer and not part of model HS-3000. IMPORTANT NOTICE: Read operating instructions of connected pressure washer. 8.913-943.0 • LANDA HS • Rev. 4/13...
1-2 minutes. IMPORTANT: The instructions on this page pertain to the pressure washer used in connection with model HS-3000. 8.913-943.0 • LANDA HS • Rev. 4/13...
3. Store the machine and accessories in a room which does not reach freezing temperatures. CAUTION: Failure to follow the above directions will result in damage to your pressure washer. 8.913-943.0 • LANDA HS • Rev. 4/13...
2-4 hours. ment clean and dry. Step 4 After circulating solution flush entire system The areas around the Landa washer should be kept with fresh water. Reinstall high pressure clean and free of combustible materials, gasoline and nozzle into wand.
Air Band replace the nozzle each season. Fuel Control System The HS-3000 utilizes a fuel solenoid valve located on the fuel pump to control the flow of fuel to the com- bustion chamber. This solenoid, which is normally closed, is activated by a flow switch when water is Part No.
Page 14
11. Reinstall new or cleaned coil reversing Steps 9 through 1. NOTE: Before step 6, lift coil and tank assembly onto some type of exposed support for ease of removing inlet and discharge fittings. 8.913-943.0 • LANDA HS • Rev. 4/13...
Obstruction in smoke stack Check for insulation blockage or other foreign objects. Soot build up on coils Clean coils with soot remover. Clean inside of coils using Landa's coil Lime build up in coils cleaner. Improper burner nozzle See exploded view parts list.
Fuel filter partially clogged Replace as needed. Soot build up on coils Clean coils with soot remover. Lime build up on coils Clean inside of coils using Landa's coil cleaner. Improper burner nozzle See exploded view parts list. WATER Incoming water to machine warm or Lower incoming water temperature.
Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your Landa, Inc. dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer.
SUREFIRE BURNER REPLACEMENT PARTS For best performance specify genuine SUREFIRE replacement parts 8.913-943.0 • LANDA HS • Rev. 4/13...
Page 25
SUREFIRE BURNER REPLACEMENT PARTS For best performance specify genuine SUREFIRE replacement parts 8.913-943.0 • LANDA HS • Rev. 4/13...
Page 27
Authorized LANDA Dealer of the defect. Your Authorized LANDA Dealer will file a claim with Landa, who must subsequently verify the defect. In most cases, the part must be returned to LANDA freight prepaid with the claim. For warranty service on components warranted by other manufacturer’s, your Authorized LANDA Dealer can help you obtain warranty service through these manufacturers’...