Page 1
OPERATOR’S MANUAL ■ PE3-1100 ■ PE4-2000 ■ PE4-3000 ■ PE5-3000 For technical assistance or the dealer nearest you consult our web page at www.landa.com 8.913-998.0...
The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference. LANDA PE • 8.913-998.0 • Rev. 03/12...
(GFCI). If rated more than 250 volts, or more than single phase this product should only be connected to a power supply receptacle protected by a GFCI. LANDA PE • 8.913-998.0 • Rev. 03/12...
Failure to protect machine from freezing could PROTECT FROM FREEZING cause malfunction of the machine and result in death, serious bodily injury, and/or property damage. Fol- low storage instructions specifi ed in this manual. LANDA PE • 8.913-998.0 • Rev. 03/12...
fl oor. This system prevents internal pump dam- Pump - Develops high pressure. age. Pump Protector - Cycles fresh cool water through pump when recirculating water reaches 140°F. LANDA PE • 8.913-998.0 • Rev. 03/12...
Water Inlet Hose STEP 7: Check inlet filters, re- move debris, then connect the garden hose to pump water inlet. CAUTION: Do not run the pump without water or pump damage will result. LANDA PE • 8.913-998.0 • Rev. 03/12...
NOTE: For a more gentle rinse, select the white 40° or green 25° nozzle. To scour the surface, select the yellow 15° or red 0° nozzle. To apply de- tergent select the black nozzle. LANDA PE • 8.913-998.0 • Rev. 03/12...
NOTE: You can also stop deter- washer in low pressure for 1-2 minutes. gent from fl owing by removing detergent siphon tube from bottle. LANDA PE • 8.913-998.0 • Rev. 03/12...
2. Restart pressure washer and let it run briefl y (about 5 seconds) until water no longer discharges from the high pressure outlet. LANDA PE • 8.913-998.0 • Rev. 03/12...
Turn machine off if not in use for over over 5 minutes 1-2 minutes. OIL DRIPPING Oil seal worn Check and replace if necessary. EXCESSIVE VIBRATION Irregular functioning of the pump Check and replace if necessary. IN HIGH-PRESSURE valves HOSE LANDA PE • 8.913-998.0 • Rev. 03/12...
Page 11
3/4 fi lled. GROWLING OR Bad bearing Replace bearing. Clean all grease from cavity WHINING and new bearing. Repack with correct grease until cavity is approximately 3/4 fi lled. LANDA PE • 8.913-998.0 • Rev. 03/12...
Shell Dolium R (Factory installed) or Chevron SRI. OIL CHANGE RECORD Date Oil Changed Estimated Operating Date Oil Changed Estimated Operating Month/Day/Year Hours Since Last Month/Day/Year Hours Since Last Oil Change Oil Change LANDA PE • 8.913-998.0 • Rev. 03/12...
Cushion, Pump Red (4-20024 ) 8.712-362.0 Nozzle, SAQC MEG 1506 Unloader, See Specifi cations Pages Yellow (4-20024) 8.712-363.0 Nozzle, SAQC, Meg 2506 Green (4-20024 ) 8.712-364.0 Nozzle, SAQC MEG 4006 White (4-20024 ) LANDA PE • 8.913-998.0 • Rev. 03/12...
Page 16
(4-20024, 4-30024, 5-30024) 8.706-655.0 Belt Guard, Small (PE3-11024) 9.802-151.0 Swivel, 1/2" JIC Fem, 8.706-656.0 Belt Guard, Large (PE) Push-On (4-20024, 4-30024, 5-30024) 9.802-710.0 Bolt, 5/16" x 1" NC, HH ▲ Label, PE 8.900-246.0 LANDA PE • 8.913-998.0 • Rev. 03/12...
500 psi limit, remove the adjusting knob (Item 18) and re-adjust (lower) the nuts (Items 15) on the stem (Item 8). Re-attach the adjusting knob (Item 18), then repeat step #6. LANDA PE • 8.913-998.0 • Rev. 03/12...
Tefl on Ring 70-120207 Stem 9.803-926.0 Brass Handle 9.803-941.0 Connector Female Kit A 8.717-672.0 O-Ring Repair Kit 9.702-892.0 Connector Male Kit B 8.717-673.0 Outlet Kit O-Ring Kit C 8.717-674.0 Stem Repair Kit Spring LANDA PE • 8.913-998.0 • Rev. 03/12...
Page 27
Authorized LANDA Dealer of the defect. Your Authorized LANDA Dealer will file a claim with Landa, who must subsequently verify the defect. In most cases, the part must be returned to LANDA freight prepaid with the claim. For warranty service on components warranted by other manufacturer’s, your Authorized LANDA Dealer can help you obtain warranty service through these manufacturers’...
Page 28
Form # 8.913-998.0 • Revised 03/12 • Printed in U.S.A. or Mexico...
Need help?
Do you have a question about the PE3-1100 and is the answer not in the manual?
Questions and answers