Programming Worksheets - DSC PC2525 Installation Manual

PROGRAMMING WORKSHEETS

[00] Binary Programming
[01] Zone Definitions
Default
2 0
I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I
2 1
I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I
2 1
I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I
2 1
I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I
0 2
I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I
0 2
I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I
0 2
I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I
0 2
I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I
[02] System Times
Default
0 3 0
I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I _ _ _ _ _ _ I
1 2 0
I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I _ _ _ _ _ _ I
0 4 5
I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I _ _ _ _ _ _ I
1 8 0
I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I _ _ _ _ _ _ I
0 0 4
I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I _ _ _ _ _ _ I
0 5 0
I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I _ _ _ _ _ _ I
[03] Installer's Code
Default
2 5 2 5
I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I
[04] Master Code
Default
1 2 3 4
I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I
[05] Second Master Code
Default
A A A A
I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I _ _ _ _ _ _ I
[06] Programmable Output Options
Default
0 1
I _ _ _ _ _ _ I _ _ _ _ _ _ I I _ _ _ _ _ _ _ I _ _ _ _ _ _ _ I
00 2-Wire Smoke
01 Utility Output
02 5-second Reset Pulse
03 Strobe Output (Latched Alarm)
04 System Status (Arm/Disarm)
05 Keypad Buzzer Follow Mode
06 Courtesy Pulse (Entry/Exit)
07 Entry Delay Follow Mode
28
Page 12
Page 12
Zone 1
Zone 2
Zone 3
Zone 4
Zone 5
Zone 6
Zone 7
Zone 8
Page 13
Entry Delay (seconds)
Exit Delay (seconds)
Auxiliary Entry Delay (seconds)
Auxiliary Exit Delay (seconds)
Bell Cut-off Time (minutes)
Loop Response Time (× 10 ms)
Page 13
Enter 4 digits using 0 through 9; do not enter [
Page 13
Enter 4 digits using 0 through 9; do not enter [
Page 13
Enter 4 digits using 0 through 9; do not enter [
Valid entries are from 01 to 15.
First Digit
0 Audible
1 Silent
2 Chime, Audible
3 Chime, Silent
• Valid entries are 001 to 255.
Do not enter 000.
NOTE: Auxiliary Delay Times must be longer
than Standard Delay times.
Loop Response Times must be in the
range of "010" to "255"; do not
program times less than "010".
∗
Page 14
08 Exit Delay Follow Mode
09 LINKS1000 Support Output
10 Ground Start Pulse
11 TLM and Alarm
12 2nd Line Slave
13 Failure to Communicate
14 Kissoff Output
15 Remote Operation (requires DLS-1 v5.3 or later)
PC2525 v1.1
Second Digit
0 Delay
1 Instant
2 Interior
3 Interior Home-Away
4 24-hour Bell
5 24-hour Bell/Buzzer
6 24-hour Buzzer
7 Auxiliary Delay
8 Delayed Fire
9 Keyswitch Arm
A Home-Away with Delay
B Forced Answer
] or [#].
∗
] or [#].
∗ ∗
] or [#]. Enter [ 1111] to erase.