Skin Tone Dtl; Knee/Level - Panasonic AJ-SPX800P Operating Instructions Manual

8-3-8 SKIN TONE DTL

Items/ Adjustable
Data Saved Range
SKIN TONE ON Set the skin tone DTL to ON or OFF.
DTL OFF
S C U F E
SKIN TONE ON ON/OFF switching for ZEBRA within the
SKIN TONE range.
ZEBRA OFF
S C U F E
SKIN DTL 0 Adjust the effect of SKIN TONE DTL
CORING.
CORING :
5
:
S C U F E 7
SKIN TONE Used when obtaining the target hue for
SKIN TONE DTL. Align the center marker
GET
and the target object with each other.
– – – – –
Y MAX 000 Set the maximum value of the brightness
signal to which SKIN TONE effect is
:
190
enabled.
:
S C U F E
255
Y MIN 000 Set the minimum value of the brightness
signal to which the SKIN TONE effect is
:
010
enabled.
:
S C U F E
255
I CENTER 000 Set the center position on the I axis (the
area where SKIN TONE is enabled).
:
022
:
S C U F E 255
I WIDTH 000 Set the area width where SKIN TONE is
enabled along the I axis above and below
:
010
the I CENTER.
:
S C U F E 255
Q WIDTH 000 Set the area width where SKIN TONE is
enabled along the Q axis above and below
:
005
the I CENTER.
:
S C U F E 255
Q PHASE –128 Set the phase in the area where SKIN TONE
is enabled based on the Q axis.
:
+000
:
S C U F E +127
R-Y
Q-WIDTH
I-WIDTH
+ direction
I-CENTER
–
direction
Q-PHASE
Remarks
Y
Y-MAX
B-Y
Y-MIN
= SKIN TONE AREA
0

8-3-9 KNEE/LEVEL

Items/ Adjustable
Data Saved Range
MASTER PED –200 Set the master pedestal.
:
+000
:
S C U F E +200
MANUAL ON Set the mode when the AUTO KNEE switch
is OFF. The KNEE POINT/SLOPE set value
KNEE OFF
is enabled when this setting is ON.
S C U F E
KNEE POINT 70.0% Set the KNEE POINT position in 0.5% steps.
:
85.0%
:
S C U F E 107.0%
KNEE SLOPE 00 Set the KNEE SLOPE.
0 setting is equal to KNEE OFF.
:
50
<Note>
:
The adjustable range when using the AJ-
99 (98)
EC3P is from 00 to 98.
S C U F E
WHITE CLIP ON Set the WHITE CLIP feature to ON or OFF.
OFF The WHITE CLIP LVL set value is enabled
when this setting is ON.
S C U F E
WHITE CLIP 90% Set WHITE CLIP LEVEL.
LVL :
105%
:
S C U F E 109%
A.KNEE POINT 80% Set the AUTO KNEE POINT position in
0.5% steps. This setting is enabled when the
:
85%
OUTPUT/AUTO KNEE selector switch is set
:
to CAM.AUTO KNEE ON.
S C U F E 107%
A.KNEE LVL 100 Set the AUTO KNEE LEVEL.
:
105
:
S C U F E 109
A.KNEE 1 Set the AUTO KNEE response speed.
RESPONSE : The smaller the setting value, the faster the
4
response speed.
S C U F E
<Note>
The items indicated by are the setting items for PAINT MENU
SW( ) R/W in the <SD CARD R/W SELECT> screen. The items
without are the setting items for PAINT MENU LEVEL R/W.
Please refer to [8-7-2 SD CARD R/W SELECT] for more
information.
The ____ in the Adjustable Range column indicates the preset
mode.
Remarks
107
8