Related Manuals for Clarke CAG2350B
Summary of Contents for Clarke CAG2350B
- Page 1 ANGLE GRINDER MODEL NO: CAG2350B PART NO: 6470099 OPERATING & MAINTENANCE INSTRUCTIONS GC0614...
- Page 2 Your Angle Grinder has been designed to give long and trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local CLARKE dealer. CONTENTS 1 x Angle Grinder 1 x Disc Guard (for depressed centre grinding discs) and Fixings (Bolt &...
-
Page 3: Environmental Recycling Policy
ENVIRONMENTAL RECYCLING POLICY Through purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE. In effect, this means that this product must not be disposed of with general household waste. -
Page 4: General Safety Rules
GENERAL SAFETY RULES CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY. WORK ENVIRONMENT 1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. - Page 5 2. Use personal protective equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hearing protection and a workshop apron capable of stopping small abrasive or workpiece fragments. 3. Avoid accidental starting. Ensure the switch is in the off position before plugging in.
-
Page 6: Angle Grinder Safety Instructions
ANGLE GRINDER SAFETY INSTRUCTIONS 1. Before starting work, always consider the following: The use of hand held angle grinders for grinding and cutting operations can present risks to the user. Full observation of the safety instructions in this user guide is essential. 2. - Page 7 12. Accessories. Only use the recommended accessories. Ensure that the wheels and discs are fitted in accordance with the manufacturer’s instructions. 13. Only use discs that comply with EN12413 or EN13236. Make sure that the disc used is suitable for the no load speed of the angle grinder. See Specifications on page 16.
-
Page 8: Disc Safety Instructions
DISC SAFETY INSTRUCTIONS 1. Disc speed. Check the speed of the disc before fitting to your angle grinder. Never use a disc with a rpm speed less than the rpm speed of your angle grinder. See specification on page 18. 2. -
Page 9: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. - Page 10 OVERVIEW NO DESCRIPTION NO DESCRIPTION Spindle Lock Button On/Off Trigger Switch Threaded hole (for handle) Air Vent Motor Brush cover plate Auxilliary Handle Safety Button 10 Disc Guard Mains Lead 11 Grinding/Cutting Disc Rear Handle Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 11: Before Use
BEFORE USE FITTING / ADJUSTING THE DISC GUARD WARNING: MAKE SURE THAT THE ANGLE GRINDER IS SWITCHED OFF AND UNPLUGGED FROM THE MAINS SUPPLY BEFORE FITTING OR REMOVING ANY ACCESSORIES. ENSURE THE CORRECT GUARD IS FITTED FOR THE DISC BEING USED. 1. -
Page 12: Fitting And Removing A Disc
FITTING AND REMOVING A DISC WARNING: MAKE SURE THAT THE ANGLE GRINDER IS SWITCHED OFF AND UNPLUGGED FROM THE MAINS SUPPLY BEFORE FITTING OR REMOVING ANY ACCESSORIES. 1. Make sure the correct disc guard is fitted before you fit any cutting/ grinding disc. -
Page 13: Fitting The Auxiliary Handle
FITTING THE AUXILIARY HANDLE 1. Fit the side handle by screwing it into one of the 3 threaded holes on the angle grinder. USING YOUR ANGLE GRINDER WARNING: FRAGMENTS FROM A BROKEN/DETACHED DISC CAN CAUSE SERIOUS INJURY. WARNING: WHEN USING CUTTING DISCS, DO NOT STAND DIRECTLY IN LINE WITH THE ROTATING DISC. -
Page 14: The On/Off Switch
THE ON/OFF SWITCH 1. To start the angle grinder, depress the safety button and squeeze the trigger upwards. NOTE: The angle grinder has a soft start feature and will take a moment to reach full speed. 2. To stop the angle grinder, release the trigger. -
Page 15: Selecting The Correct Guard
• Type 41 - Flat cutting off wheels. • Type 42 - Depressed centre cutting off wheels. SUITABLE ABRASIVE AND CUTTING DISCS The following Clarke discs are suitable for use with the CAG2350B. Always use the correct disc and guard type for its intended task. Model No... -
Page 16: Changing The Carbon Brushes
3. Repeat on the other side of the body. • Both brushes should be replaced at the same time. SPECIFICATIONS Model Number CAG2350B Dimensions (L x W x H) 530 x 250 x 160 mm Weight 5 kg Input Power... -
Page 17: Parts List And Diagram
PARTS LIST & DIAGRAM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 18 PARTS LIST & DIAGRAM Description No Description Upper Securing Flange Rotor Lower Securing Flange Air Baffle Guard Bearing Hex Screw Bearing Leather Ring Square Nut Stator Woodruff Key Stator Pressure Board Output Shaft Screw Screw Housing Washer Brush Holder Front Cover Brush Bearing Screw &...
-
Page 19: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...