Subscribe to Our Youtube Channel
Related Manuals for Clarke CAT65
Summary of Contents for Clarke CAT65
- Page 1 ANGLE DIE GRINDER SET MODEL NO: CAT65 PART NO: 3110725 OPERATING & MAINTENANCE INSTRUCTIONS GC0614...
- Page 2 INTRODUCTION Thank you for purchasing this CLARKE Angle Die Grinder Set. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
-
Page 3: General Safety Rules
GENERAL SAFETY RULES CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY. WORK ENVIRONMENT 1. Keep the work area clean and tidy. 2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair out of the way. -
Page 4: Transportation And Storage
8. Do not carry out any alterations or modifications to the tool. 9. Always disconnect from the air supply when: • Performing any maintenance. • The tool is not in use. • The tool will be left unattended. • Moving to another work area. •... - Page 5 OVERVIEW The CAT65 Die Grinder Set includes the accessories shown. When opening the case for the first time, check against the following list that all the items are present. Any damage or deficiency should be reported to your CLARKE dealer immediately.
-
Page 6: Specifications
2.5 m/s Please note that the details and specifications contained herein are correct at the time of going to print. However CLARKE International reserve the right to change specifications at any time without prior notice. Always consult the machine’s data plate. -
Page 7: Compressed Air Requirements
COMPRESSED AIR REQUIREMENTS WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND COMPRESSED AIR SUPPLY. • Use only clean, dry, regulated compressed air as a power source. • Air compressors used with the tool must comply with the appropriate European Community Safety Directives. -
Page 8: Before Use
Your air tool is now ready for use. You can fit a whip hose with a quick fit coupling if required (available from your Clarke dealer). INSTALLING THE COLLET TO THE DIE GRINDER 1. Select the grinding stone you require. -
Page 9: Setting The Speed
FITTING THE GRINDING STONE INTO THE DIE GRINDER IMPORTANT: Never use chipped or cracked grindstones. Never use grindstones not rated to operate at a speed equal to, or greater than, the full operating speed of the air tool. 1. Slip the shank of the chosen stone into the collet and tighten the screw cap finger tight. -
Page 10: Grinding Tips
1. Before use, drain water from the air tank, air line and compressor. 2. Pour a few drops of CLARKE airline oil, into the air inlet. This should be carried out regardless of whether or not an in-line mini oiler is used. If an in- line mini oiler is not used, this procedure should be repeated after every two to three hours of use. -
Page 11: Service And Repair
If the tool is to be stored, or is idle for longer than 24 hours, run a few drops of Clarke air line oil into the air inlet, and run the tool for 5 seconds in order to lubricate the internal parts. -
Page 12: Troubleshooting
2. Motor parts worn. 2. Return to Clarke dealer for repair. 3. Worn or sticking 3. Drip air tool lubricating mechanism due to oil into air inlet. Allow oil lack of lubricant. -
Page 13: Parts Diagram - Die Grinder
PARTS DIAGRAM - DIE GRINDER Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 14: Parts List - Die Grinder
PARTS LIST - DIE GRINDER Description No Description Main Body Steel Ball ////////////////////////////////// /////////////////////////////////// End cap Ball Bearing ////////////////////////////////// //////////////////////////////////// Strainer //////////////////////////////////// Throttle Lever /////////////////////////////////// Hinge Pin Collet Bush Collett Chuck Valve Spanner O-Ring Spanner Spring Bush Speed Control Valve Front Plate O-Ring Housing End... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the CAT65 and is the answer not in the manual?
Questions and answers