Table of Contents
Advertisement
Owner's Manual
CAUTION:
1.
Weight on this product should not exceed 300 lbs.
2.
Class H equipment: This equipment is for home
use only. It is not for commercial use.
2006, 02
This Product is Produced Exclusively by
2040 N. Alliance, Springfield, MO 65803
Customer Service Number
1 (800) 375-7520
www.staminaproducts.com
!
WARNING
Exercise can present a health
risk. Consult a physician
before beginning any exercise
program with this equipment.
If you feel faint or dizzy,
immediately discontinue use
of this equipment. Serious
bodily injury can occur if this
equipment is not assembled
and used correctly. Serious
bodily injury can also occur if
all instructions are not
followed. Keep others and
pets away from equipment
when in use. Always make
sure all bolts and nuts are
tightened prior to each use.
Follow all safety instructions in
this manual.
When calling for parts or
service, please specify the
following number.
55-1522
STAMINA PRODUCTS
MADE IN CHINA
Product May Vary Slightly
From Pictured.
2006 Stamina Products, Inc.
!
Advertisement
Table of Contents
Related Manuals for Stamina CoreTraining Inversion System
Summary of Contents for Stamina CoreTraining Inversion System
- Page 1 Class H equipment: This equipment is for home use only. It is not for commercial use. Product May Vary Slightly From Pictured. This Product is Produced Exclusively by 2040 N. Alliance, Springfield, MO 65803 Customer Service Number 1 (800) 375-7520 www.staminaproducts.com 2006, 02 2006 Stamina Products, Inc.
-
Page 2: Table Of Contents
TABLE OF CONTENTS Page Page Safety Instructions Maintenance Instructions Before You Begin Warranty Hardware Identification Chart Product Parts Drawing Assembly Instructions Parts List Operational Instructions Notes Storage Fax/Mail Ordering Form SAFETY INSTRUCTIONS WARNING: To reduce the risk of serious injury, read the following safety instructions before Core Training Inversion System using the Read the Warning Label posted on the Front Base Frame. - Page 3 CALL US FIRST THANK YOU FOR PURCHASING THE Core Training Inversion System Simply follow the few assembly instructions set forth in this manual. Within a few minutes you will be getting your body into shape and on your way to achieving a happier and healthier lifestyle.
-
Page 4: Before You Begin
BEFORE YOU BEGIN Thank you for choosing the Core Training Although Stamina tries to manufacture its products Inversion System. We take great pride in producing with the finest materials and uses the highest this quality product and hope it will provide many... -
Page 5: Hardware Identification Chart
HARDWARE IDENTIFICATION CHART This chart is provided to help identify the hardware used in the assembly process. After unpacking the unit, open the hardware bag and make sure that you have the following items: 3/16" 1/4" 5/16" 3/8" 1/2" INCHES 100 110 120 130 140 150 MILLIMETERS length... -
Page 6: Assembly Instructions
ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. - Page 7 ASSEMBLY INSTRUCTIONS STEP 4 "L" LEFT PIVOT ARM(7), "R" RIGHT PIVOT ARM(8). There is a decal on the and a decal on the LINKAGE(16) RIGHT FRONT FRAME(2), Refer to the Inset drawing. Insert the through the bracket on the LINKAGE(16) RIGHT PIVOT ARM(8) NYLOCK NUT(M8)(64).
- Page 8 ASSEMBLY INSTRUCTIONS STEP 7 SLIDER SUPPORT(11) CROSSING FRAME(6) BUTTON Attach the onto the Bracket on the with HEAD BOLT(M10 x 90mm)(62), NYLOCK NUT(M10)(65), WASHER(M10)(68). STEP 8 CABLE(35) LEVER(36). LEVER(36) Straighten the on the Refer to the Inset drawing. The should be LEFT PIVOT ARM(7).
- Page 9 ASSEMBLY INSTRUCTIONS STEP 10 SUPPORT PLATES(23) BACK FRAME(9) FLAT HEAD BOLTS(M6 x 50mm) Attach the onto the with (54), WASHERS(M6)(66), NYLOCK NUTS(M6)(63). NOTE: SUPPORT PLATE(23) FLAT HEAD BOLT(M6 x 50mm)(54), The lowest is attached with a no washer and nut needed. STEP 11 BACK FRAME(9) A, B, C,...
- Page 10 ASSEMBLY INSTRUCTIONS Securing Pad must face down BOTTOM VIEW STEP 12: BELT GUIDES(27) SEAT Refer to the Bottom View in the illustration. Attach the onto the CUSHION(25) BUTTON HEAD BOLTS(M8 x 15mm)(58) WASHERS(M8)(67). with Make the SEAT BELT(26) BELT GUIDES(27) SEAT Securing Pad face down and insert the through the...
- Page 11 ASSEMBLY INSTRUCTIONS STEP 15 CUSHION SUPPORT TUBES(14) LEG SUPPORT FRAME(13) BUTTON Attach the onto the with HEAD BOLTS(M6 x 65mm)(57), WASHERS(M6)(66), NYLOCK NUTS(M6)(63). STEP 16 LEG SUPPORT CUSHIONS(28) CUSHION SUPPORT TUBES(14) BUTTON Attach the onto the with HEAD BOLTS(M8 x 30mm)(59) WASHERS(M8)(67).
- Page 12 ASSEMBLY INSTRUCTIONS STEP 17 LEFT RIGHT HANDRAIL ASSEMBLIES(17, 18) SHAFTS LEFT Attach the onto the in the RIGHT FRONT FRAMES(1, 2) LINKAGES(16) LOCKING KNOBS(21). and the with the STEP 18 Core Training Inversion System. Verify that the handlebars function correctly before using the Move BACK CUSHION(24) HANDRAILS(17, 18)
-
Page 13: Operational Instructions
OPERATIONAL INSTRUCTIONS GENERAL PRECAUTIONS Core Training Inversion System Do not use the alone. Always have a helper available in case assistance is needed in recovering from the decline position. LEVER(36), CABLE(35), SPRING PIN(34). Check the Make sure the system works smoothly BEFORE Core Training Inversion System. - Page 14 OPERATIONAL INSTRUCTIONS FOAM PAD USE AND ADJUSTMENT FOAM PADS(30) Place your feet under the with your legs FOAM PADS(30) LEG SUPPORT between the and the CUSHIONS(28). SPRING KNOB(29). SPRING KNOB(29) Loosen the Pull the FOAM PAD SUPPORT(15) and slide the toward you until your FOAM PADS(30) legs are properly held between the...
- Page 15 OPERATIONAL INSTRUCTIONS USING THE SEATED INVERSION SYSTEM Start by sitting on the machine and leaning back on the back cushion with your hands at your side, or resting on your thighs. Pull and hold the LEVER(36) with your left hand. Use the handrail and your right hand to rotate the BACK CUSHION(24) slowly backward.
-
Page 16: Storage
Worn or damaged components shall be replaced immediately or the Core Training Inversion System removed from service until repair is made. Only Stamina Products supplied components shall be used to maintain/repair the Core Training Inversion System. Keep your Core Training Inversion System clean by wiping with an absorbent cloth after use. -
Page 17: Warranty
To implement this limited warranty, send a written notice stating your name, date, and place of purchase and a brief description of the defect along with your receipt to Stamina Products, Inc. P.O. Box 1071, Springfield Missouri, USA, 65801-1071 or call us at 1 (800) 375-7520. If the defect is covered under this limited warranty, you will be requested to return the product or part to us for free repair or replacement at our option. -
Page 18: Product Parts Drawing
PRODUCT PARTS DRAWING BACK FRONT... -
Page 19: Parts List
PARTS LIST DIAGRAM# PART NAME Left Front Frame Right Front Frame Rear Frame Front Base Frame /w Warning Label Rear Base Frame Crossing Frame Left Pivot Arm Right Pivot Arm Back Frame Back Support Bar Slider Support Seat Frame Leg Support Frame Cushion Support Tube Foam Support Linkage... - Page 20 PARTS LIST DIAGRAM# PART NAME Round Plug (22mm) Square Plug (33.4mm x 33.4mm) Square Plug (38mm x 38mm) Rectangular Plug (20mm x 40mm) Rectangular Plug (23.5mm x 53.5mm) Screw, Round Head (M4 x 20mm) Bolt, Round Head (M6 x 1 x 20mm) Bolt, Flat Head (M6 x 1 x 50mm) Bolt, Button Head (M6 x 1 x 15mm) Bolt, Button Head (M6 x 1 x 47mm)
-
Page 21: Notes
NOTES... -
Page 22: Fax/Mail Ordering Form
FAX/MAIL ORDERING FORM Please do not return the product. For your convenience, Stamina has a Customer Service Department with a toll-free number. Should a part be missing or a defective part found, please call 1 (800) 375-7520 (in the U.S.) between 8:00 A.M. and 5:00 P.M. Central Time, Monday through Friday or fill out the fax sheet ordering form below and fax it to (417) 889-8064.