Safety instructions Delivery The electrical connection conditions must correspond 1. Check the packaging and with the specifications dishwasher immediately for on the dishwasher rating plate 9:. damage caused in transit. Do not switch on a damaged If the power cord of this appliance, but contact your appliance is damaged, supplier.
Safety instructions If you cannot obtain any In daily use information from Read and observe the safety the manufacturer, you must information and instructions not install the dishwasher for use on the packaging above or below these for cleaning and rinsing agents. appliances.
Safety instructions ã= Deactivating the button lock: Warning Risk of injury! Hold down the button + for To prevent injuries, e.g. approx. 4 sec. until the caused by stumbling, open display goes out. the dishwasher only briefly When the programme ends in order to load and unload on the digital display), the the dishwasher.
Safety instructions ã= When opening and closing Warning the door on an eye-level Risk of scalding! appliance, ensure that Open the door carefully when children do not become the programme is still running. jammed or crushed between There is a risk of hot water the appliance door and the spraying out of the appliance.
Water softening system/Special salt Appliance interior Water softening system/Special salt 1" Interior light * s a l t e m / S p e c i a l n g s y s t s o f t e n i W a t e r 1* Top basket To ensure good washing results,...
Water softening system/Special salt To change the setting: 2. Fill the tank with water (only required when switching on the appliance for 1. Press programme button 3. the first time). Each time the button is pressed, the 3. Then add dishwasher salt (not table set value increases by one level;...
Rinse aid 1. Open the dispenser 9" by pressing Switching off salt refill and lifting the plate on the cover. indicator/water softening system Sw i t c h i n g of f w a t e r so f t e n i n g s y s t e m If the salt refill indicator @ is impaired (e.g.
Utensils 3. Hold down programme button # Utensils and press START button h until : ..is indicated on the digital U t e n s i display. Not suitable 4. Release both buttons. The LED for button # flashes and Cutlery and utensils made of wood.
Utensils Loading the dishwasher Cups and glasses Top basket 1* 1. Remove large food remnants. It is not necessary to prerinse utensils under running water. 2. Place the utensils so that – they are secure and cannot tip over. – all utensils with their openings face down.
Utensils Etagere * Et a g e r e Heavily soiled utensils (pans) should be placed in the bottom basket. The The etagere and the space underneath more powerful spray jet provides can be used for small cups and glasses a better dishwashing result.
Utensils Small accessories holder * A djusting the height of the Sm a l l ac c e s s o r i e s ho l d e r Ad j u s t i n g t h e h e i g h t o f t h e b a s k e t basket * * depending on model Light-weight plastic accessories, e.g.
Utensils Top basket with side levers 1. Pull out the top basket 1* out. 2. To lower the basket, press in the left and then the right lever on the outside of the basket. In doing so, hold the sides of the basket along the upper edge to prevent it from suddenly dropping.
Detergent Adding detergent Detergent 1. If the detergent dispenser 9* is still D e t e r g e closed, press the lock 92 to open You can use tablets as well as powder or liquid detergents for dishwashers, but the detergent dispenser.
Detergent Notes If the utensils are only lightly soiled, You will obtain optimum rinsing slightly less than the indicated amount and drying results by using solo of detergent is usually adequate. detergents and applying salt and rinse aid separately. Suitable detergents and care products If programmes are short, tablets can be purchased online may not have full cleaning effect...
Overview of programmes Overview of programmes p r o g r a m m e s O v e r v i e w o f The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options · Information for test institutes Hygiene * Hy g i e n e Test institutes receive the information for The temperature is increased during the comparability tests (e.g. according to cleaning process. This increases the EN60436). hygiene status. This additional option is ideal for cleaning e.g.
Operating the appliance Note Operating - for environmentally friendly operation the appliance of the dishwasher: For ecological reasons the Eco 50° a n c e a p p l i n g t h e O p e r a t i programme is preset whenever the appliance starts.
Operating the appliance Timer programming * Automatic switch off after end T i m e r p r o g r a m m i n g of programme or interior light* Au t o m a t i c s w i t c h of f / i n t e r i o r l i g h t * depending on model You can delay the start of the * depending on model...
Operating the appliance T erminating the programme To change the setting: Te r m i n a t i n g t h e pr o g r a m m e 1. Press programme button 3. (Reset) Each time the button is pressed, the set value increases by one level;...
Cleaning and maintenance ã Warning – Health hazard 3. Remove any residue and clean filters under running water. Never use other domestic detergents, e.g. containing chlorine! 4. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after Special salt and rinse aid closing the filter system.
Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display 8 lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min.
Fault, what to do? Fault Cause Remedial action A different error code is A technical fault has probably Switch off appliances with the ON/OFF switch (. After a short time restart indicated on the digital occurred. display. the appliance. to : If the problem recurs, turn off the tap and pull out the mains plug.
Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid Refill rinse aid. in the dispenser. Programme selected without Select programme with drying (see drying. Overview of programmes, Programme sequence). Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
Fault, what to do? Fault Cause Remedial action Food remnants Utensils placed too closely Arrange utensils with adequate clearance on the utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
Fault, what to do? Fault Cause Remedial action Water stains on plastic Droplet formation on plastic Use a more intensive programme (more parts surface is physically unavoidable. water changes). After drying, water stains are Arrange utensils in a sloping position. visible.
Fault, what to do? Fault Cause Remedial action Coloured (blue, yellow, Film formation consisting Can be partly removed with machine brown), difficult to remove of ingredients from vegetables cleaner or by mechanical cleaning. Coatings to non-removable coatings (e.g. cabbage, celery, potatoes, are harmless.
Fault, what to do? Fault Cause Remedial action Rust spots on the cutlery. Cutlery not adequately rust- Use corrosion-resistant cutlery. resistant. Knife blades are frequently more severely affected. Cutlery will also rust if rusting Do not wash rusting parts. parts are rinsed at the same time (pan handles, damaged utensil baskets, etc.).
Fault, what to do? Fault Cause Remedial action Appliance stops Door not closed properly. Close the door. in the programme or Do not place utensils or fragrance Check whether rear panel is being pressed programme is interrupted. dispenser in the tablet collecting in, e.g.
Customer service Customer service Installation and connection e r v i c e C u s t o m e r s If you are unable to rectify the fault, i o n a n d c o n n e c t l a t i o n I n s t a l please contact your customer service.
Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions can thoroughly in the factory to ensure that it be found in the installation instructions. is in working order. This may cause Level the appliance with the aid of the small water stains.
Installation and connection Drinking water connection Warm water connection * Wa r m wa t e r co n n e c t i o n 1. Fasten the drinking water connection * depending on model to the tap according The dishwasher can be connected to the installation instructions using to cold or hot water up to max.
Installation and connection Electrical connection Removing the appliance Connect the appliance to an Also observe alternating current only, ranging from the sequence of worksteps here. 220 V to 240 V and 50 Hz or 60 Hz 1. Disconnect the appliance from via a correctly installed socket with the power supply.
Installation and connection Transportation Protection against frost Pr o t e c t i o n a g a i n s t fr o s t ( E m p t y i n g t h e a p p l i a n c e ) Empty the dishwasher and secure loose If the appliance is in a room where there parts.