Keep bystanders, children, and visitors away while operat- ing a power tool. Distractions can cause you to lose control. Technical data D28000 ELECTRICAL SAFETY Rated voltage 220-240~ Grounded tools must be plugged into an outlet properly...
Page 4
Using an extension cable PERSONAL SAFETY • Stay alert, watch what you are doing and use common If an extension cable is required, use and approved extension sense when operating a power tool. Do not use tool while cable suitable for the power input of this tool (See technical data). tired or under the influence of drugs, alcohol, or medica- The minimum conductor size is 1.5 mm tion.
Page 5
Additional Specific Safety Instructions • Disconnect the plug from the power source before making for Grinders any adjustments, changing accessories, or storing the tool. • Always use proper guard with grinding wheel. A guard pro- Such preventative safety measures reduce the risk of starting tects operator from broken wheel fragments and wheel contact.
Page 6
• When the wheel is pinched or bound tightly by the workpiece, • Direct sparks away from operator, bystanders or flammable the wheel stalls and the motor reaction drives the unit rapidly materials. Sparks may be produced while cutting and/or back toward or away from the operator.
Your risk from these exposures varies, depending on how often FIG. 1 you do this type of work. To reduce your exposure to these chem- icals: work in a well ventilated area, and work with approved safe- ty equipment, such as those dust masks that are specially designed to filter out microscopic particles.
M10 hub. Every unthreaded accessory must have a 16mm arbor ASSEMBLY AND ADJUSTMENTS hole. If it does not, it may have been designed for a circular saw and ATTACHING SIDE HANDLE (Optional) should not be used. Use only the accessories shown on pages 9–10 The side handle (H) can be fitted to either of this manual.
Page 9
To reduce unexpected tool movement, do not switch the NOTE: tool on or off while under load conditions. Allow the grinder to run 100mm Grinding Wheels up to full speed before touching the work surface. Lift the tool from the surface before turning the tool off. Allow the tool to stop rotating before putting it down.
Page 10
100mm Cutting Wheels Please use the correct size of accessories according the rated size in nameplate. Do not use accessories designed for 125mm grinder on a 100mm grinder! Type 1 guard Type 1 guard Mounting and Using Depressed Center Grinding Wheels and Sanding Flap Discs backing flange backing flange...
Page 11
Depressed center Type 27 grinding wheels SURFACE GRINDING WITH GRINDING WHEELS must be used with included flanges. See 1. Allow the tool to reach full speed before touching the tool to the page 9 of this manual for more information. work surface.
Page 12
4. Once a cut is begun and a notch is established in the work- wheels provided with a M10 threaded hub. A Type 27 guard is piece, do not change the angle of the cut. Changing the angle required when using wire brushes and wheels. will cause the wheel to bend and may cause wheel breakage.
Page 13
5. Continuously move the tool in a forward Fasten the screw to secure the guard and back motion to avoid creating gouges in on the gear case cover. You should be the work surface. Allowing the tool to rest on unable to rotate the guard by hand the work surface without moving, or moving when the screw is fastened.
4. Depress the spindle lock button and tighten clamp nut with center for correct carbon brush. Use of carbon brush not a wrench. designed for this tool or not qualified by D WALT may 5. To remove the wheel, grasp and turn while depressing the damage the tool and may result serious injury! spindle lock button.
Page 15
CAUTION: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. Use a clean, dry cloth only. Lubrication WALT tools are properly lubricated at the factory and are ready for use. Repairs To assure product SAFETY and RELIABILITY, repairs, mainte- nance and adjustments should be performed by a D WALT factory service center, a D...
Page 17
DeWALT 1-YEAR WARRANTY DeWALT warrants this product for one year from date of purchase. We will repair, without charge, any defects due to faulty material and/or workmanship. Please return the complete until, transportation prepaid, to any local DeWALT Service Center with valid DeWALT warranty card AND invoice/receipt copy.
Page 18
ª√–∑— ∫ μ√“√â “ π§â “ ª√–∑— ∫ μ√“√â “ π§â “ Please return this warranty card together with copy of invoice or receipt to the local DeWALT Service centre within 14 days from purchase of your tool. °√ÿ ≥ “ à ß §◊ π „∫√— ∫ ª√–°— 𠔇π“„∫‡ √Á ® ∑’ Ë »Ÿ π ¬å ∫ √‘ ° “√¢Õß...