Table of Contents
Advertisement
Assembly – Hanging the Fan (continued)
6
Making the electrical connection
IMPORTANT: Use the wire connecting nuts supplied with
your fan. Secure the connectors with electrical tape and
ensure there are no loose strands or connections.
Connect the two green fan wires (II) to the household wire
(II).
If you are using the optional light kit, connect the blue fan
wire (JJ) and the black fan wire (KK) to the black household
wire (KK).
Connect the fan motor white wire (LL) to the receiver (PP)
white wire (LL) using a wire nut.
Connect the fan motor black wire (KK) to the receiver (PP)
black wire (KK) using a wire nut.
Connect the fan motor blue wire (JJ) to the receiver (PP)
blue wire (JJ) using a wire nut.
Connect the receiver (PP) red wire (OO) to the supply black
(hot) wire (KK) using a wire nut.
Connect the receiver (PP) white wire (LL) to the supply
white wire (neutral) (LL) wire using a wire nut.
Spread the wires apart so that the green (II) and white (LL)
wires are on the side of the outlet box (MM) and the black
wire (KK) is on the other side.
Turn the wire connecting nuts upward and push the wiring
into the outlet box (MM).
NOTE:The frequencies on your receiver and transmitter have
beet preset at the factory. Before installing the receiver, make
sure the dip switches on the receiver and transmitter are set
to the same frequency. The dip switches on the transmitter
are located inside the battery compartment.
WARNING: Each wire nut supplied with this fan is designed
to accept up to one 12-guage house wire and two wires from
the fan. If you have larger than 12-guage house wiring or more
than one house wire to connect to the fan wiring, consult an
electrician for the proper size wire nuts to use.
MM
PP
LL
JJ
KK
LL
7
Mounting the fan
WARNING: When using the standard ball/downrod
mounting, the tab in the ring at the bottom of the mounting
bracket must rest in the groove of the hanger ball. Failure to
properly seat the tab in the groove could cause damage to
the wiring.
Align the locking slots of the ceiling canopy (C) with the
two screws in the mounting bracket (A). Push up to engage
the slots and turn clockwise to lock in place.
Firmly tighten the two mounting screws.
Install the remaining two mounting screws into the holes in
the canopy (C) and tighten rmly.
Install the decorative canopy ring by aligning the ring's
slots with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock in place.
Close-To-Ceiling Mounting
Carefully unhook the fan from the mounting bracket (A) and
align the locking slots of the ceiling canopy (C) with the two
screws in the mounting bracket (A). Push up to engage the
slots and turn clockwise to lock in place. Immediately
tighten the two mounting screws rmly.
Install the remaining two mounting screws into the holes in
the canopy (C) and tighten rmly.
Install the decorative canopy ring by aligning the ring's slots
with the screws in the canopy (C). Rotate the ring
counter-clockwise to lock in place.
You may now proceed to attaching the fan blades.
WARNING: Locking slots of celling canopy are provided
only as an aid to mounting. Do not leave fan assembly
undattended until all four canopy screws are engaged and
rmly tightened.
l P
a e
e s
o c
t n
9
A
C
H
A
M
c a
1 t
8 -
7 7
5 -
7 2
0 -
1 3
f 3
r o
u f
t r
P
O T
N
B
Y A
C .
O
M
e h
a r
s s
s i
a t
c n
. e
Hide quick links:
Advertisement
Table of Contents
