Display Options - KMC Controls FlexStat Operation Manual

Display Options

WED 11/19 3:20 PM
COOL:
OCC:
FAN:
HUM: 36% RH
Fahrenheit decimal values are not displayed by de-
fault but can be enabled in the User Interface menu.
See Show Temperature Tenths (Decimals) on page
21.
With R2.0.0.13 and later firmware, Fahrenheit tem-
perature values on the display change in whole
degree increments by default, and Celsius values
change in 0.5° increments. Changing the default No
to Yes will show tenths of a degree values for both
scales.
This does not affect setpoint adjustments, which are
always in whole degree increments for Fahrenheit
and half degree increments for Celsius.
WED 11/19 3:22 PM
COOL:
OCC:
FAN:
HUM: 37% RH
To toggle the displayed temperature scale between
Fahrenheit and Celsius, press the Enter button for at
least two seconds until the desired scale is displayed.
(Pressing Enter for less time will turn on the back-
light if it is off.) The desired scale will persist on the
display until this process is repeated or the FlexStat
is restarted.
After a restart, the temperature scale will revert to
whatever scale is set in the Application menu. To
change the scale so that it persists after restarting,
change it in the Application menu by resetting the
selected application to Not Configured, changing
the temperature scale, and then reconfiguring all the
application options. See
Additional Setup on page
WED 11/19 3:20 PM
COOL:
OCC:
FAN:
HUM: 36% RH
Date and Time Display are enabled by default, but
they can be turned off and replaced by a rotating
clock icon. See Show Time and Date on page
FlexStat
WED 11/19 3:22 PM
COOL:
OCC:
FAN:
HUM: 37% RH
WED 11/19 3:22 PM
COOL:
OCC:
FAN:
HUM: 37% RH
(Advanced) Application and
7).
COOL:
OCC:
FAN:
HUM: 36% RH
21.
WED 11/19 3:20 PM
COOL:
OCC:
FAN:
HUM: 36% RH
By default, rotation values in the lower right of the
screen show relative humidity and/or CO
models with the relevant optional sensors. If more
than one value is shown, the values will rotate ap-
proximately every five seconds.
These values can be hidden if desired, and additional
options are also available. See
page 21.
WED 11/19 3:20 PM
COOL:
OCC:
FAN:
HUM: 36% RH
Hospitality mode has a simpler display and limited
menus, and it is typically used in hotel rooms. Users
typically can change only the setpoint, system mode,
and fan speed. Pushing the Left and Right buttons
displays customizable menu selections. See
page 21.
WED 11/19 3:20 PM
COOL:
OCC:
FAN:
HUM: 36% RH
When Display Blanking is enabled, the display
turns off at the same time the backlight goes off
(after reset, initial power-up, or time-out). When any
button is pressed, the display will reappear until the
time-out is reached again. See
page 21.
NOTE: Displays can also be locked. Locked UI
mode appears like Standard mode on the
Home screen, but all button functions
(except the backlight) are disabled. The
setpoint and other operation functions
cannot be changed by the user. See
page 21.
NOTE: The contrast of the LCD display can also be
adjusted. See
5
WED 11/19
OUTSIDE: 56° F
levels in
2
Rotation Values on
WED 11/19
HUM: 36% RH
Mode on
Display Blanking on
Mode on
Contrast on page 21.
Operation Guide, Rev. R
3:20 PM
COOL:
OCC:
FAN:
3:20 PM
COOL:
FAN: