Vent System Identification - Empire Comfort Systems DVX36FP32CLN-2 Installation Instructions And Owner's Manual

Installing Vent Components (Figure 48)
Begin the vent system installation by installing the first Simpson
Duravent component, 90° elbow to the starting collars or straight
pipe on the top of the appliance, then the straight pipe length and
then horizontal or vertical termination kit.
NOTE: A ll outer connection joints must be sealed with aluminum
tape, screws or silicone sealant rated above 300°F/149°C. The
inner flue joints do not require any sealant.
Simpson Duravent vent system components lock into place by sliding
the concentric pipe section with four (4) equally spaced interior beads
onto the appliance collar or previously installed component end with
four (4) equally spaced indented sections. When the internal beads
of each starting outer pipe line up, rotate pipe section clockwise 90°
(approximately 3 inches). The vent pipe is now locked together.
Continue adding components per the pre-planned vent system
configuration. Be certain that each succeeding vent component
is securely fitted and locked into the preceding component in the
vent system.
Special Venting Components (Simpson Duravent)
See Empire Comfort Systems Retail Price List for Simpson
Duravent part numbers and pricing.
Special DV Vent Kits
Available from Empire Comfort Systems, Inc. dealers.
DVVK-4VP Direct-Vent Fireplace Vent Kit - Vertical, Includes
(DVVK-4V) SD-991, SD-953, and SD-943
Direct-Vent Fireplace Vent Kit for Top Vent,
DVVK-4TP Thru-the-wall, 8 to 11 inch wall thickness,
(DVVK-4T) Includes SD-911, SD-985, SD-990 and
SD-942
Direct-Vent Fireplace Vent Kit for Top Vent, Thru-
DVVK-4TSP
the-wall, 5 to 7 inch wall thickness, Includes
(DVVK-4TS)
SD908, SD-985, SD-990 and SD-942
DVVK-4FV Direct-Vent Fireplace Vertical Flex Vent Kit
Direct-Vent Fireplace Vent Kit, Thru-the-wall, 5
DVVK-4RE
to 13 3/4 inch wall thickness
Page 32

VENT SYSTEM IDENTIFICATION

90° ELBOW
OR
45° ELBOW
90° ELBOW
CEILING FIRESTOP
WALL STRAP
PIPE LENGTH
Special DV Vent Kits
Available from Empire Comfort Systems, Inc. dealers.
Direct-Vent Fireplace Vent Kit for Rear Vent, 6 to
DVVK-5RP
12 inch wall thickness, Includes SD-1208, SD-
(DVVK-5R)
1247, and SD-2184
Direct-Vent Fireplace Vent Kit for Top Vent, Thru-
DVVK-5TP
the-wall, 4 to 6 inch wall thickness, Includes SD-
(DVVK-5T)
1290, SD-1284, SD-1208 and SD-1247
DVVK-5VP Direct Vent Fireplace Vent Kit - Vertical, Includes
(DVVK-5V) SD-1291, SD-1253, and SD-1243
Top Vent Kit (Horizontal) - 4½" to 6" wall thickness
DVVK-5TS
(114.3mm to 152mm)
DVVK-5F Horizontal Flex Vent Kit (4' Flex) (1.22m)
WALL THIMBLE
VERTICAL
TERMINATION
(MAXIMUM OF
THREE 90° ELBOWS)
HORIZONTAL
STORM COLLAR
TERMINATION
(MAXIMUM OF
TWO 90° ELBOWS)
Figure 48
30329-0-0312
ROOF FLASHING