SCHUBERTH S2 Owner's Manual

Helmet

Hide thumbs Also See for S2:

Manual (149 pages)

Faq (3 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for SCHUBERTH S2

Page 1 Owner`s Manual How to choose and use your helmet properly. english 3 - 67 français 68 - 131 español 132 - 195 Warning: This helmet is sold without warranty, expressed or implied concerning this product´s ability to protect the user from any injury or death! The user assumes all risks! Warning: This helmet is not a toy.
Page 2 Pay particular attention to points highlighted as follows: You have made an excellent choice with the SCHUBERTH S2. The S2 is the result of the latest development and production Warning: methods. You can take pleasure in knowing that you own...
Page 3: Table Of Contents
Retention system Replacement Parts Pinlock ® visor Communication systems Sun visor Ordering Original SCHUBERTH Parts Inner lining After sales service ......... 104 Ventilation systems Additional safety features Limited warranty Customer service administrator Putting on and taking off the helmet ....86...
Page 4: Read First
Never use the helmet with the lining removed! an accident. Always use approved Schuberth parts when If the lining is not installed before use, the helmet may not replacing shields, screws, or any other parts. A weakened fit properly and could come off in an accident, resulting in helmet will not provide head protection.
Page 5 C. READ FIRST will weaken the hard coating, damaging the shields. Do not Warning: drive with a dim or blurred shield. Impaired vision can cause Don’t mistreat your helmet! an accident resulting in serious personal injury or death. Never ride with the helmet hanging from the helmet holder, and do not hang the helmet from angled supports such as Warning: a mirror.
Page 6: The Helmet
4. OUTER SHELL Certifying authority ECE test standard The outer shell of the S2 combines an aerodynamically optimal shape that is suitable for racing with thorough protection. Serial number Certification number It consists of glassfibre reinforced vinylester (GRP) with 051234/P-1234 polyethylene fibre reinforced layers.
Page 7: Inner Shell
Even Note: when traveling at higher speeds, the S2 generates practically no upward lift. Other characteristics of the S2 are improved air Please note that with faired motorcycles strong eddy currents resistance, reduced buffeting and directional stability.
Page 8: Wind Deflector
The improved sealing in the lower section of the helmet can lead to an increased concentration of moisture inside the The retention system of the S2 consists of a chinstrap that is helmet, and thus to misting of the face shield, sun visor and additionally secured with neckbands at the back of the helmet eye glasses.
Page 9 D. THE HELMET Adjusting the chinstrap The length of the chinstrap is adjusted by increasing or reducing the length of strap pulled through the metal buckle. Adjust the length of the chinstrap so that it fi ts fi rmly but comfortably under your chin and fi x the end of the strap using the retaining loop with comfort pad.
Page 10 ® inner visor may only be used in conjunction with the SCHUBERTH main face shield that has been specially Changing the visor shield is easy to do without tools using the designed for this purpose. Other face shields must not be convenient EasyChange visor mechanism.
Page 11: Pinlock ® Visor
D. THE HELMET Removing the face shield 2. The face shield will then audibly lock into place when you press it gently towards the helmet with a 1. Move the face shield into the simultaneous closing movement. uppermost locked position. 2.
Page 12 D. THE HELMET 3. The Pinlock ® visor should now be 2. To reduce the pretensioning of the positioned in the face shield with Pinlock ® visor slightly if necessary, its lower edge parallel to the lower use the balls of your thumbs to edge of the face shield.
Page 13: Sun Visor
D. THE HELMET Note: 11. SUN VISOR Never press the locking pins out with your fingers as they may break. Sun visor Caution: The sun visor is tinted grey and has a 3D shape. Thanks to the As a result of the double shield lens structure, there is a sun visor's 1.5mm thickness, it provides protection against small possibility of greater light reflection in the face schield, stone chips or insects when driving with the visor up.
Page 14: Inner Lining
12. INNER LINING Removing the sun visor The replaceable inner lining of the S2 is washable and ensures both an excellent fi t and improved ventilation of the helmet. 1. Pivot the sun visor down.
Page 15 D. THE HELMET All parts of the inner lining are made from materials that 3. Take hold of the chinstrap pad and are gentle on the skin (especially those that come into direct pull the loop of the neckband out contact with the head).
Page 16 D. THE HELMET Fitting the high-comfort cheek pads 5. Push the plastic tongue with round holes on the head pad over the pin 1. Button the chinstrap pad on to the sewn in to the back of the cheek chinstrap and thread the chinstrap pad and fix it in place using the through the loop on the chinstrap red plug-in strip.
Page 17: Ventilation Systems
1. Slide the plastic strip gradually under the notches of the plastic The S2 has a face shield that adjusts to several positions. Depen- strip attached to the inner shell. ding on your road speed and the tendency of the face shield to mist up, open the face shield sufficiently wide to stop it misting up but so that it still protects your eyes from excessive draft.
Page 18 Ventilation device 2 – inlet vent in chin area Summer and winter adjustment (face shield ventilation) The ventilation of the S2 can also be adjusted to suit the seasons, To ventilate the face shield, the S2 weather conditions or your personal is provided with an inlet in the chin preferences.
Page 19: Additional Safety Features
If the helmet is plain (no the helmet is positioned fully in decoration), the SCHUBERTH name also appears on the front and the air flow when travelling). This back of the helmet in a reflective film.
Page 20: Putting On And Taking Off The Helmet
If you wish, you can apart. send your S2 to the SCHUBERTH customer service department to be checked free of charge (see Section J.1. After sales service). 3. It will now be easy to put the helmet on.
Page 21: Checking The Face Shield And Sun Visor
F. BEFORE EVERY JOURNEY G. FOR YOUR SAFETY 3. CHECKING THE FACE SHIELD AND SUN VISOR 1. SAFETY ADVICE CONCERNING THE HELMET Before every journey, check that the mechanisms of the face Warning: shield and sun visor are working properly and that the face Never ride without a helmet! shield and sun visor will provide sufficiently clear visibility.
Page 22: For Your Safety
G. FOR YOUR SAFETY in an accident resulting in severe head injury or death. For Warning: detailed information regarding proper fit, see section D. Don’t mistreat your helmet! Never ride with the helmet hanging from the helmet holder, Warning: and do not hang the helmet from angled supports such as Always check your helmet before every ride! a mirror.
Page 23: Safety Advice Concerning The Faceshield / Sun Visor
Keep your helmet (faceshield and sun visor) in good molding can expose edges that may injure you in an condition! accident. Always use approved Schuberth parts when If your faceshield or sun visor become too scratched or replacing shields, screws, or any other parts. A weakened uncleanable, replace it with a new one.
Page 24: Safety Advice Concerning Modifications / Accessories
Removing parts such as the mouth guard or rubber face molding can expose edges that may injure you in an accident. Always use approved SCHUBERTH parts when replacing shields, screws, or any other parts. A weakened helmet will not provide head protection.
Page 25: Maintenance And Care
H. MAINTENANCE AND CARE 1. OUTER SHELL Inside surface of the face shield To clean the helmet shell, you can use water, soapy water or The inside surface of the face shield must only be cleaned with one of the commonly available motorcycle shampoos, cleaners, a soft cloth, which may be slightly dampened if required (we polishes and plastic cleaners, or cleaning fluid.
Page 26: Inner Lining
3. INNER LINING The inner lining of the S2 can be removed completely. The head and cheek pads can be washed by hand using a mild soap 3. On completion of the cleaning, solution (e.g.
Page 27: Storing The Helmet 100
Caution: For safety reasons, all other parts of the helmet should be replaced by the SCHUBERTH Repair Service only. 2. REPLACEMENT PARTS Set of cheek pads (2 in no.) (must be exchanged by an authorized dealer or Customer Service Department) size 53 (SH item no.
Page 28: Accessories And Spare Parts 101
Inc., if you need replacement parts. will lose its approval. Your S2 is supplied ready for installation of the SCHUBERTH SRC- System™ as standard. The S2 is already fitted with two integrated antennas to amplify reception and a Bluetooth connection, to provide you with the best possible radio reception.
Page 29: After Sales Service
If we determine that the item cannot be repaired, we will arrange for a replacement at no additional cost to you. This warranty sets forth in full the complete liabilities and obligations of SCHUBERTH and its customer service administrator in respect to breach of warranty.

SCHUBERTH S2 Owner's Manual

Quick Links

Related Manuals for SCHUBERTH S2

Summary of Contents for SCHUBERTH S2

Table of Contents