Programming The Control For The Pager; Programming For Access Control - ADEMCO

Vista-32FB Installation And Setup Manual

VISTA-32FB/VISTA-128FB Installation and Setup Guide

Programming the Control for the Pager

x In field *64 enter 1 to enable the 4100APG pager
interface.
x In field *65 enter the phone number of the paging
service for Alarm reports. Up to 17 digits may be
entered.
x In field *66 enter the Pager ID number of the
paging service for Alarm reports. This is the PIN
number. Up to 10 digits may be entered.
x In field *67 enter the phone number of the paging
service for Trouble reports. Up to 17 digits may be
entered.
x In field *68 enter the Pager ID number of the
paging service for Trouble reports. This is the PIN
number. Up to 10 digits may be entered.
x In field *69 enter the phone number of the paging
service for Bypass reports. Up to 17 digits may be
entered.
x In field *70 enter the Pager ID number of the
paging service for Bypass reports. This is the PIN
number. Up to 10 digits may be entered.
x In field *71 enter the phone number of the paging
service for Open/Close reports. Up to 17 digits may
be entered.

Programming for Access Control

VistaKey
See the VistaKey-SK Installation and Setup Guide for
the detailed programming instructions.
VistaKey Dialer Enables
When the VistaKey is installed with an alarm system,
the system defaults are set so that the system does not
send reports to the central station. The programming is
accomplished in field 1 35 for the following events:
x ACS Troubles - To enable or disable ACS trouble
reporting.
ACS Bypasses - To enable or disable ACS bypass
x
reporting.
x ACS System - To enable or disable ACS system
reporting, (i.e., ACS module reset).
x ACS Alarms - To enable or disable ACS alarm
reporting.
x Dialer (Trace) - To enable or disable access
grant/denial events sent to the central station.
The PassPoint ACS can dedicate some of its inputs for
use as regular control panel hardwired zones (the zone
response type is ACS). The PassPoint ACS can also
utilize the control panel dialer for reports to the central
station.
4-8
x In field *72 enter the Pager ID number of the
paging service for Open/Close reports. This is the
PIN number. Up to 10 digits may be entered.
x In field *73 enter the phone number of the paging
service for System reports. Up to 17 digits may be
entered.
x In field *74 enter the Pager ID number of the
paging service for System reports. This is the PIN
number. Up to 10 digits may be entered.
In field *75 enter the phone number of the paging
x
service for Test reports. Up to 17 digits may be
entered.
In field *76 enter the Pager ID number of the
x
paging service for Test reports. This is the PIN
number. Up to 10 digits may be entered.
x In field 1*70 enable the events for the event log.
x In field 1*72 enable the Printer On-Line option.
This must be turned on to allow events to be sent to
the pager interface when they occur.
Field 3*19 MUST be programmed with a "1" in
order for the printer and pager to operate
properly.
Using ACS Zone Inputs
If the PassPoint ACS has uncommitted zones, these
may be used by the VISTA-32FB/VISTA-128FB as
hardwired zones. To program for ACS zone inputs,
perform the following steps:
Step Action
1 Enter Zone Programming in the #93 Menu
Mode.
2 Program this zone as any other zone. Indicate
the input type as ACS (10).
3 Enter the PassPoint ACS's zone ID (00-31)
See Zone Programming in the Programming Guide for a
detailed explanation.
PassPoint Dialer Events
All PassPoint ACS events can be sent to the VISTA-
32FB/VISTA-128FB dialer via the VGM. These events
will also be logged into the control's event log. This is
enabled in the PassPoint ACS. See the PassPoint ACS
documentation for a detailed explanation.
Programming the VISTA Gateway Module
See the PassPoint ACS instructions to program the
VISTA Gateway Module.