1. Manuals
  2. Brands
  3. Planet Manuals
  4. Security Camera
  5. CAM-ISD52
  6. User manual

Planet CAM-ISD52 User Manual

23x indoor speed dome camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
23x Indoor Speed Dome Camera
CAM-ISD52
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for Planet CAM-ISD52

Summary of Contents for Planet CAM-ISD52

  • Page 1 23x Indoor Speed Dome Camera CAM-ISD52 User’s Manual...

  • Page 3: Table Of Contents

    CONTENTS 1. Safety Information................4 2. Preface....................5 3. Features .....................6 4. Appearance..................7 DIP switches ..............8 Set Up Device ID Number ...........9 RS-485 Network and Impedance.......27 5. Mount the Speed Dome Camera .............30 Mounting Accessory...........31 Ceiling-drop mount (with CAM-CM)......32 Wall mount (with CAM-WM)........33 Use External Housing (with CAM-OH).......35 6.
  • Page 4 Scan................61 Control ............... 63 Privacy Mask ............. 64 Alarm ................. 66 9. Pre-defined System Functions ............69 10. Specification................... 70 User’s manual...

  • Page 5: Safety Information

    1. Safety Information Federal Communication Commission (FCC) Statement : This equipment has been tested and found to comply NOTE with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 6: Preface

    2. Preface Congratulations for the purchasing of the world most compact PTZ (Pan, Tilt and Zoom) camera. The camera is designed and manufactured not just to meet the requirements for traditional CCTV and modern digital surveillance, but also increase the systems’ overall performance. This camera line incorporates high resolution color CCD, with two types of lens available: power zoom or vari-focal.

  • Page 7: Features

    3. Features Compact Size of 5” (135 mm)(10x zoom version 4-1/2” -114 mm) diameter Continuous panning for 360 ; Tilt for180 (10x zoom version is 90 Fast rotation speed, up to 240 per second RS-485 digital control, supporting multi-nude topology BNC connector for video output Programmable for view position, speed and dwell View position preset, up to 128 points...

  • Page 8: Appearance

    4. Appearance 4.1 To Access DIP Switches Before the camera is mounted in place, be sure the following four settings are properly executed, or the camera may fail the control: Camera ID setup Protocol selection Baud rate selection Termination impedance Tools: Use pencil, pincer, paper clip or small flat screw driver, to move the lever of DIP switch...

  • Page 9: Dip Switches

    4.1 DIP switches Overview of DIP switches There are three sets of DIP switch on board for different setup purposes. location # bit quantity used for DS1+DS2 Device ID setup (P1&2) Protocol / baud rate setup (P3~P7) Network impedance Refer to the picture on below for DIP switch locations. The following paragraphs are providing the detail descriptions of the three main setups.

  • Page 10: Set Up Device Id Number

    4.2 Set Up Device ID Number To build correct network for control communication, every speed dome camera in the network must have an unique ID number, which is set by the bit 1 to 10 of a DIP switch DS1(bit1-8) & DS2(bit 1~2). Factory default of device ID is 1 Note: remark: D...
  • Page 11 ID table (1 ~ 64) on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on...
  • Page 12 ID table (65 ~ 128) on on on on on on on on 100 on on on on on on 102 on on on on on on on on on on on on 104 on on on on on on on 106 on on on on on...
  • Page 13 ID table (129 ~ 256) 130 on 162 on 132 on on 164 on on 134 on 166 on on on on on 136 on on on 168 on on on 138 on 170 on 140 on on 172 on on on on on on 142 on...
  • Page 14 ID table (193 ~ 256) on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on on...
  • Page 15 ID table (257 ~ 320) 258 on 290 on 260 on on 292 on on 262 on 294 on on on on on 264 on on on 296 on on on 266 on 298 on 268 on on 300 on on on on on on 270 on...
  • Page 16 ID table (321 ~ 384) on on 322 on 354 on on on on on 324 on on 356 on on on on on on 326 on 358 on on on on on on on on on 328 on on on 360 on on on on on on on...
  • Page 17 ID table (385 ~ 448) on on on on 386 on on on 418 on on on on on on on 388 on on on on 420 on on on on on on on on 390 on on on 422 on on on on on on on...
  • Page 18 ID table (449 ~ 512) 449 -- on on on 481 -- on on on on 450 on on on on 482 on on on on on 451 -- on on on 483 -- on on on on 452 on on on on on 484 on on on on on on...
  • Page 19 ID table (513 ~ 576) 514 on 546 on 516 on on 548 on on 518 on 550 on on on on on 520 on on on 552 on on on 522 on 554 on 524 on on 556 on on on on on on 526 on...
  • Page 20 ID table (577 ~ 640) on on 578 on 610 on on on on on 580 on on 612 on on on on on on 582 on 614 on on on on on on on on on 584 on on on 616 on on on on on on on...
  • Page 21 ID table (641 ~ 704) 642 on 674 on 644 on on 676 on on 646 on 678 on on on on on 648 on on on 680 on on on 650 on 682 on 652 on on 684 on on on on on on 654 on...
  • Page 22 ID table (705 ~ 768) 705 -- on on 737 -- on on on 706 on on on 738 on on on on 707 -- on on 739 -- on on on 708 on on on on 740 on on on on on 709 -- on on...
  • Page 23 ID table (769 ~ 832) on on on on 770 on on on 802 on on on on on on on 772 on on on on 804 on on on on on on on on 774 on on on 806 on on on on on on on...
  • Page 24 ID table (833 ~ 896) on on on on on on 834 on on on 866 on on on on on on on on on on on 836 on on on on 868 on on on on on on on on on on on on 838 on...
  • Page 25 ID table (897 ~ 960) on on on on on on 898 on on on on 930 on on on on on on on on on on 900 on on on on on 932 on on on on on on on on on on on 902 on on on on...
  • Page 26 ID table (961 ~ 1024) 961 -- on on on on on on on on on 962 on on on on on 994 on on on on on on 963 -- on on on on on on on on on 964 on on on on on on 996 on on...
  • Page 27 Control protocol and baud rate must be set correctly to the camera in order to establish proper and stable communication between camera and control device. Be sure that the same protocol and baud rate are selected in control device, too. Presently 6 types of protocol and 3 levels of baud rate are provided by this speed dome, through an 8-bit DIP switch labeled DS2.

  • Page 28: Rs-485 Network And Impedance

    4.3 RS-485 Network and Impedance Transmission distances of RS-485 Bus The 0.56mm (24AWG) twisted pair or higher grade wires are recommended for data transmission cable. The maximum theoretical transmitting distances, for the AWG#24, are as follows: Baud Rate Maximum Transmitting Distance 2400 Bps 1800m 4800 Bps...
  • Page 29 Impedance setup for the speed dome Each speed dome camera has a termination resistor built in. In a network of RS-485 chain, the speed domes are classified in two categories: end unit (such as the #31) and node (such as #1 through #30). To set up the resistor correctly, installer must decide if the specific dome camera is the termination device or not, i.e.
  • Page 30 standards, problems such as signal reflections, lower anti-interference performance arise when the cables are long in the connection. The reliability of control signals could be downgraded with the phenomena that the dome does not respond to or just responds at intervals to the controller, or does continuous operation without stop.

  • Page 31: Mount The Speed Dome Camera

    5. Mount the Speed Dome Camera The camera and its mounting system are designed in modules. There are 5 methods to mount the PTZ camera, which are: Attached to the ceiling surface directly Embedded into ceiling Held to ceiling surface through a bracket (ceiling-drop) Mounted to wall through a bracket Adapted into external housing For all these five mounting ways, a common mounting base for mechanical locking...

  • Page 32: Mounting Accessory

    5.1 Mounting Accessory The following items are supplied with the speed dome for the camera mounting. Description The look The Use The interface for holding Mounting base the camera and bridging signals To work with item 3 for Metal Bowl creating ceiling or wall holder mount...

  • Page 33: Ceiling-Drop Mount (With Cam-Cm)

    5.2 Ceiling-drop mount (with CAM-CM) Pre-assembling of the Bowl Module Both ceiling-drop and wall-mount needs to have a bowl module, an assembly of the mounting base and metal bowl supplied in the mounting kit, be built first. Follow the flow chart on below for building up the bowl module. Make a Put the base module...

  • Page 34: Wall Mount (With Cam-Wm)

    5.3 Wall mount (with CAM-WM) Pre-assembling of the Bowl Module Both ceiling-drop and wall-mount needs to have a bowl module, an assembly of the mounting base and metal bowl supplied in the mounting kit, be built first. Follow the flow chart on below for building up the bowl module. Make a Put the base module...
  • Page 35 Make it an Put the bowl assembly on bracket The bowl module Locate the assembled piece onto the place the camera is to be mounted, and fix it on the surface completely with screws through the 4 holes on the bracket Get the camera and plug it onto the base;...

  • Page 36: Use External Housing (With Cam-Oh)

    5.4 Use External Housing (with CAM-OH) To operate speed dome cameras and maintain all functions in normal in severe temperature conditions, i.e. below -10 C or above 45 C, external housing is required. CAM-OH has included two brackets (Ceiling-mount and Wall-mount bracket). You can choose which one you will like to used.
  • Page 37 Put the cables in the trench of bracket, and all connectors come out through the cable outlet. Then put bracket cover and screw back. Load the camera into the housing. Be sure the connectors are well mated and then rotate the camera to lock it in position. Put the safety screw in locking position and tight it.
  • Page 38 Ceiling mount Installation Procedure 1. Insert the cables pass through the tube. Please also stuff the water proof rub ring into the iron cover on tube. 2. Close the tube onto the outdoor housing and lock it to the housing. Tight them on with screws.

  • Page 39: Connecting Wires

    6. Connecting Wires The cables, wires and connector attached to the speed dome are categories into 4 major functions of: Power Video RS-485 Alarm-in and out They are easily distinguished from one to another, as being featured with different connectors. Refer to the picture on below to learn about cable and connector information.

  • Page 40: Video

    With outdoor housing, AC24V: An AC adapter of 24V / 1.66A is supplied with the outdoor housing (CAM-OH) for the AC version. To power the camera, connect adapter to camera’s power connector. Power Connector on Speed Dome AC 24V Connector on Adaptor As soon as power is supplied, the speed dome will enter “initial check”...

  • Page 41: Rs-485

    6.3 RS-485 The camera adapts RS-485 in half-duplex pattern, which is a two-pin connectivity, as shown on the right picture. Installer must pay attention to the polarity of these two pins – yellow wire is the POSITIVE end, and orange is the NEGATIVE.
  • Page 42 The three inputs and their correspondent view presets are independent from one to another. Therefore, with the connections to three sensors, installer can set up camera to monitor three different spots with different dwell time. Presets For Events Default settings at the alarm-ins activations are: If setting(s) is / are done to presets 17, 18 and 19 : At the trigger of alarm-in number 1, lens will move to preset 17.
  • Page 43 Camera is in steady mode when alarm signal(s) kicks in When the first alarm signal hits this camera, lens will move to the corresponding presets (see relative information on above ) at maximum speed of 300 per second Lens will stay at the preset position for 60 seconds Camera will be back to the original position after 60 seconds, if no second alarm-in jumps in this 60 second time frame.

  • Page 44: Applications

    7. Applications The PTZ camera, by itself alone or encompassed in different numbers of domes with comprehensive matrix switching, is mainly for link to 4 different control means (also known in different terms such as controller, console or host): PC-based system Keyboard controller (Digital Video Recorder ) Video server...

  • Page 45: Connect Single Dome To Console

    7.2 Connect single dome to console Connect the RS-485 of camera to controller ) with a pair of (such as a keyboard twisted cable. Tele-control is sent via the cable between dome and controller. Video signal from the dome is sent to multiplexer, monitor, DVR or video server directly, normally through coaxial cable (usually the RG-59 A/U).
  • Page 46 Connect Speed dome to standalone DVR Connect the RS-485 of camera to controller ) with a pair of (in this case, the DVR twisted cable. Tele-control is conducted from the DVR via the cable between the PTZ device and DVR. Video signal from the dome is sent to DVR also, then forwarded to monitor through the multiplexer inside the DVR.
  • Page 47 Connect Speed dome to video server Video server, the contemporary device for transmitting video throughout LAN and WAN, can also be the controlling tool for this speed dome camera. Most video servers in market are built with RS-485 communication port, and single video input for connecting one camera.

  • Page 48: Connect Two Or More Domes To Console

    7.3 Connect two or more domes to console As the RS-485 supports multi-drop topology, two or more domes can be connected to one controller in a system. For such application, the following rules must be kept: All the speed domes should be connected to host in daisy chain pattern. Star type of configuration should be prohibited to avoid system instability.
  • Page 49 User’s manual...
  • Page 50 Connect Speed Dome and PC (Capture Card) When PC is used as the console, installer needs to connect both of video and RS-485 signals to PC separately. Most capture cards have 4 video input per card, and normally each PC can handle 4 cards, meaning up to 16 cameras can be hooked to one PC.

  • Page 51: Camera Setup

    8. Camera setup --- OSD functions For the version with Power Zoom, many functions are available to users for setup and fine tune through controllers. To access the functions and make adjustment, follow the instructions on below: (NOTE: all the procedure in this paragraph is NOT applied to the version of vari-focal lens) 8.1 OSD operation This PTZ camera has many functions available to users’...

  • Page 52: System Info

    8.2 System Info To choose your controller and review the basic setup done to this unit. Controller: Keyboard and DVR are two most common devices used for PTZ control. However, controllers are sometimes very different in certain functions, which you may find PTZ works perfectly with certain controllers but not with the some others.

  • Page 53: Camera

    8.4 Camera This section is to let you choose the correct camera version, define or adjust the image and optical functions, and decide the zooming speed. Camera Type: Show camera version. Zoom Speed: to set the speed of zooming. It is recommended that you test different speed before making final choice.
  • Page 54 Manual: to adjust color preference manually. Manual setting is to let you fix the color temperature. This mode can be good choice for indoor and static environment. If the lighting is tungsten or alike (more natural), try to add more blue or reduce red a little; If lighting is fluorescent or within white spectrum, try to add more red or reduce the blue.
  • Page 55 You are suggested to make tests, to all options in list, on site, in order to make final and correct choice. Motion DET: Not an available function for this model. Focus Focusing is one of the most important and frequently-used functions of a zoom camera.
  • Page 56 Zoom TRK: this is to drive focus-lens to move along and be coordinated with zoom-lens, in order to keep image clear during the entire zooming journey. Zoom SPEED: to set the speed of zooming. Fast speed and slow speed have their own goodness and weakness.
  • Page 57 Exposure: Exposure is the key you can decide the image quality with. Exposure setting is highly dependant to the ambient light (type and intensity), and sometimes will need for different setting from one situation to another. In this section you have 3 items that can change actual exposure and 3 others are for image quality modification: exposure factor: iris, shutter, sens-up...
  • Page 58 Shutter : Shutter is the “pseudo” mechanism for controlling light energy by varying CCD exposure time. For normal indoor use, shutter speed is usually set to 1/60 sec . In (1/50 for PAL ) stronger light condition, shutter speed must be reduced, or image could be too bright.
  • Page 59 SSNR : Super Noise Reduction, for improving quality of the video captured in dark. OFF, low, mid and high are the options When camera works in dark and video gets weak, a lot of noise will be observed on image and recorded Such (snow-like spots) noise will down grade the quality and performance of the entire...
  • Page 60 In this section more advanced functions. However, some of Special: them are not available in this model. User Preset: not available to this model; although you may access the sub-menu, do changes to the settings, they won’t be executed nor saved. Keep it in OFF position all the time.
  • Page 61 SYNC: This model does not provide external sync option, so nothing needs to be done for this. Comm. Adj.: this is the communication setup for camera and the main CPU, not a user function. Please leave it untouched. If you make change to it, camera will re-start automatically to retrieve normal communication..

  • Page 62: Scan

    8.5 Scan You may choose the most suitable auto-run function among the various patterns given by this camera; When engaged, camera will move, in clockwise direction, from one preset to the next until stop is called. 3 sub-items: Auto Pan Pan / Tilt To do continuous pan/tilt between two positions A and B.
  • Page 63 OFF. Then choose the speed and dwell length for all the stops. Activate the function with RUN command on list. Pattern is a function allows you create specific path Pattern with individually-defined stops, corresponding dwell and zoom position for continuous monitoring by auto-running.

  • Page 64: Control

    8.6 Control In this section you can define how the camera will react to recovery from power down, long release from control, and make adjustment to image. To decide whether camera will go auto-run after Auto Resume manual control stops for certain time. First you decide if you want to drive the camera into AUTO-RUN with ON / OFF selection, then you choose what type of auto-run and how long the...

  • Page 65: Privacy Mask

    8.7 Privacy Mask To provide mask for privacy protection. All models in this PTZ series have total 8 masks available. Two types of mask setup and grouping are provided for versions ( A) and WDR versions ( ight type type type of mask function Total number of mask / group...
  • Page 66 important: It is strongly suggested to set up mask in comply with factors: have the target in relative large size give mask size twice big as the target’s, or even larger Although not recommended, it is also possible that the second boarder is out of the target area .

  • Page 67: Alarm

    8.8 Alarm This camera has 8 sensor inputs and two relay outputs (toggle) for event management. The alarm inputs can work with positive or negative-trigger source, with auto-detection. All the inputs are checked by software at power-on and monitored. If input status is reversed (i.e.
  • Page 68 RELAY / OUTPUT To make arrangements for relays, in terms of on/off and the corresponding time-length. Enter the sub-page and you will read RELAY 1 RELEY 2 OUTPUT1 OUTPUT2 RETURN The relays built in this camera & (what we call “alarm-out” Relay 1 are mechanical switches that have in this manual)
  • Page 69 The default number is 3 minutes. If timer is set for “0”, the Relay will keep the Alarm-on mode until it’s manually switched off. OUTPUT 2 OUTPUT 1 INPUT 1 INPUT 1 INPUT 2 INPUT 2 INPUT 3 INPUT 3 INPUT 4 INPUT 4 INPUT 5...

  • Page 70: Pre-Defined System Functions

    9. Pre-defined System Functions Power-up action After the power is first applied to a dome it will perform a self-test procedure. This calibrates and checks the basic functions of the dome. External controls are overruled during this self-test period. After the self-test, the PTZ camera will be ready for control. If the device was running the Auto-pan function before power was broken, the speed dome will retrieve Auto Scan function until new control is given by an operator.

  • Page 71: Specification

    10. Specification Camera Module and Lens Manufacturer Sony Resolution 520 TV lines Size 1/4” OSD menu Image control Optical Zoom Digital 3.8 ~ 88.4 mm Focal length F 1.6 ~ 3.0 Aperture size Color mode 0.6 lux Light sensitivity Black / white 0.1 lux Pan / Tilt Functions Stepping motors...
  • Page 72 Temperature -20℃ ~ 60℃ Storage Humidity 20 ~ 100% RHD FCC, CE Certification Dome camera 1 set Inside the box User’s manual 1 set (Option) Screw Pack 1 set Installation Kit Installation base 1 piece Metal bowl holder 1 piece 2351-L00220-999 User’s manual...

Table of Contents