Page 1 Signamax™ Connectivity Systems Model 065-7726SPOE 24-Port PoE Managed Fast Ethernet Switch with 2 SFP Dual Media Ports U s e r ’ s G u i d e...
Page 3 Signamax 065-7726SPOE User's Manual 24-Port PoE Managed Fast Ethernet Switch with 2 SFP Dual Media Ports Release 0.92...
Page 5: Table Of Contents
2-1-3-2. Cabling Requirements for 1000SX/LX SFP Module ----------- 14 2-1-3-3. Switch Cascading in Topology --------------------------------------- 15 2-1-4. Configuring the Management Agent of the 065-7726SPOE------- 18 2-1-4-1. Configuring the Management Agent of the 065-7726SPOE through the Serial RS-232 Port ------------------------------------- 19 2-1-4-2.
Page 6 3-3. P E------------------------------------------------------------------------------------- 62 3-4. SNMP C ------------------------------------------------------------- 66 ONFIGURATION 3-5. DHCP B -------------------------------------------------------------------------- 68 3-6. IGMP S --------------------------------------------------------------------- 69 NOOPING 3-7. VLAN----------------------------------------------------------------------------------- 73 3-7-1. VLAN Mode -------------------------------------------------------------------- 73 3-7-2. Tag-based Group ------------------------------------------------------------- 75 3-7-3. PVID------------------------------------------------------------------------------ 78 3-7-4. Port-based Group------------------------------------------------------------- 80 3-8.
Page 7: Revision History
Revision History Release Date Revision 0.92 10/04/2005...
Page 9: Caution
Caution Circuit devices are sensitive to static electricity, which can damage their delicate electronics. Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge. To protect your device, always: Touch the metal chassis of your computer to ground the static electrical charge before •...
Page 11 About this user’s manual In this user’s manual, it will not only tell you how to install and connect your network system but configure and monitor the 065-7726SPOE through the built-in CLI and web by RS-232 serial interface and Ethernet ports step-by-step. Many...
Page 12: Chapter 1. Introduction
1. Introduction 1-1. Overview of the 065-7726SPOE 065-7726SPOE, a 24 Fast Ethernet + 2 Gigabit L2 Managed Switch, implemented with 24 10/100Mbps TP + 2 Gigabit dual media ports with TP/SFP, is a standard switch that meets all IEEE 802.3/u/x/z Gigabit, Fast Ethernet and Ethernet specifications.
Page 13 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual • • • • Key Features in the Device QoS: Support Quality of Service by the IEEE 802.1P standard. There are two priority queue and packet transmission schedule using Weighted Round Robin (WRR).
Page 14: Checklist
Please notify your sales representative immediately if any of the aforementioned items is missing or damaged. 1-3. Features The 065-7726SPOE, a standalone off-the-shelf switch, provides the comprehensive features listed below for users to perform system network administration and efficiently and securely serve your network.
Page 15 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual • • • • Management • Supports concisely the status of port and easily port configuration • Supports per port traffic monitoring counters • Supports a snapshot of the system Information when you login •...
Page 16 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual • Supports 120 event log records in the main memory and display on the local console Publication date: Oct.., 2005 Revision A1...
Page 17: View Of The 065-7726Spoe
PoE Managed Switch User Manual 1-4. View of the 065-7726SPOE Fig. 1-1 Full View of the 065-7726SPOE 1-4-1. User Interfaces on the Front Panel (Button, LEDs and Plugs) There are 24 TP Fast Ethernet ports and 2 slots for optional removable modules on the front panel of the switch.
Page 18 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual • • • • LED Indicators Color Function System LED CPURUN Green Lit when CPU is on and good POWER Green Lit when AC power is on and good...
Page 19: User Interfaces On The Rear Panel
One RS-232 DB-9 interface is offered for configuration or management. And there is one AC power input socket for having the switch powered on or off. AC Line 100-240V 50/60 Hz RS-232 DB-9 Connector Fig. 1-3 Rear View of the 065-7726SPOE Publication date: November, 2005 Revision A0.92...
Page 20: View Of The Optional Modules
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 1-5. View of the Optional Modules In the switch, Port 25, 26 includes two types of media --- TP and SFP Fiber (LC, BiDi LC…); this port supports 10/100/1000Mbps TP or 1000Mbps SFP Fiber with auto-detected function.
Page 21: Chapter 2. Installation
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 2. Installation 2-1. Starting 065-7726SPOEUp This section will give users a quick start for: Hardware and Cable Installation - Management Station Installation - Software booting and configuration 2-1-1.
Page 22 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual • TP Port and Cable Installation ⇒ In the switch, TP port supports MDI/MDI-X auto-crossover, so both types of cable, straight-through (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 1, 2, 3, 6 in 10/100M TP;...
Page 23: Installing Chassis To A 19-Inch Wiring Closet Rail
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 2-1-2. Installing Chassis to a 19-Inch Wiring Closet Rail Fig. 2-2 Caution: Allow a proper spacing and proper air ventilation for the cooling fan at both sides of the chassis.
Page 24: Cabling Requirements For Tp Ports
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 2-1-3-1. Cabling Requirements for TP Ports ⇒ For Fast Ethernet TP network connection  The grade of the cable must be Cat. 5 or Cat. 5e with a maximum length of 100 meters.
Page 25: Switch Cascading In Topology
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 2-1-3-3. Switch Cascading in Topology • • • • Takes the Delay Time into Account Theoretically, the switch partitions the collision domain for each port in switch cascading that you may up-link the switches unlimitedly.
Page 26 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Case1: All switch ports are in the same local area network. Every port can access each other (See Fig. 2-3). Fig. 2-3 No VLAN Configuration Diagram If VLAN is enabled and configured, each node in the network that can communicate each other directly is bounded in the same VLAN area.
Page 27 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Case 2b: Port-based VLAN (See Fig.2-5). Fig. 2-5 Port-based VLAN Diagram 1. VLAN1 members could not access VLAN2, VLAN3 and VLAN4 members. 2. VLAN2 members could not access VLAN1 and VLAN3 members, but they could access VLAN4 members.
Page 28: Configuring The Management Agent Of The 065-7726Spoe
065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 2-1-4. Configuring the Management Agent of the 065-7726SPOE We offer you three ways to startup the switch management function. They are RS-232 console, CLI, and Web. Users can use any one of them to monitor and configure the switch.
Page 29: Configuring The Management Agent Of The 065-7726Spoe Through The Serial Rs-232 Port
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 2-1-4-1. Configuring the Management Agent of the 065-7726SPOEthrough the Serial RS-232 Port To perform the configuration through RS-232 console port, the switch’s serial port must be directly connected to a DCE device, for example, a PC, through RS-232 cable with DB-9 connector.
Page 30 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Username = admin Password = admin Publication date: Oct.., 2005 Revision A1...
Page 31 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual • • • • Set IP Address, Subnet Mask and Default Gateway IP Address Please refer to Fig. 2-7 CLI Management for details about the ex-factory setting. They are default setting of IP address. You can first either configure your PC IP address or change IP address of the switch, next to change the IP address of default gateway and subnet mask.
Page 32: Configuring The Management Agent Of The 065-7726Spoe Through The Ethernet Port
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 2-1-4-2. Configuring the Management Agent of the 065-7726SPOEthrough the Ethernet Port There are three ways to configure and monitor the switch through the switch’s Ethernet port. They are CLI, Web browser and SNMP manager. The user interface for the last one is NMS dependent and does not cover here.
Page 33: Ip Address Assignment
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Fig. 2-10 the Login Screen for Web 2-1-5. IP Address Assignment For IP address configuration, there are three parameters needed to be filled in. They are IP address, Subnet Mask, Default Gateway and DNS.
Page 34 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual With the classful addressing, it divides IP address into three classes, class A, class B and class C. The rest of IP addresses are for multicast and broadcast. The bit length of the network prefix is the same as that of the subnet mask and is denoted as IP address/X, for example, 192.168.1.0/24.
Page 35 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Class D and E: Class D is a class with first 4 MSB (Most significance bit) set to 1-1-1-0 and is used for IP Multicast. See also RFC 1112. Class E is a class with first 4 MSB set to 1-1-1-1 and is used for IP broadcast.
Page 36 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual In this diagram, you can see the subnet mask with 25-bit long, 255.255.255.128, contains 126 members in the sub-netted network. Another is that the length of network prefix equals the number of the bit with 1s in that subnet mask.
Page 37 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual For different network applications, the subnet mask may look like 255.255.255.240. This means it is a small network accommodating a maximum of 15 nodes in the network.
Page 38 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual has a static IP address. To connect to a server, the client needs to know the IP of the server. However, user generally uses the name to connect to the server. Thus, the switch DNS client program (such as a browser) will ask the DNS to resolve the IP address of the named server.
Page 39: Typical Applications
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 2-2. Typical Applications The 065-7726SPOEimplements 24 Fast Ethernet TP ports with auto MDIX and 2 Gigabit dual media ports with SFP for removable module supported comprehensive fiber types of connection, including LC, BiDi LC for SFP. For more details on the specification of the switch, please refer to Appendix A.
Page 40 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Fig. 2-15 Daisy-Chain Fiber Network Connection Fig. 2-16 Uninterrupted Power Supply for IP Phone Application Publication date: Oct.., 2005 Revision A1...
Page 41: Chapter 3. Operation Of Web-Based Management
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3. Operation of Web-based Management This chapter instructs you how to configure and manage the 065- 7726SPOEthrough the web user interface it supports, to access and manage the 24 10/100Mbps TP + 2 Gigabit dual media ports with TP/SFP Fiber management Ethernet switch.
Page 42 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual In the switch, it supports a simple user management function allowing only one administrator to configure the system at the same time. If there are two or more users using administrator’s identity, the switch will allow the only one who logins first...
Page 43: Web Management Home Overview
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-1. Web Management Home Overview After you login, the switch shows you the system information as Fig. 3-2. This page is default and tells you the basic information of the system, including “Model Name”, “System Description”, “Location”, “Contact”, “Device Name”, “System Up...
Page 44 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Fig. 3-3 port detail information In Fig. 3-3, it shows the basic information of the clicked port. With this, you’ll see the information about the port status, traffic status and bandwidth rating for egress and ingress respectively.
Page 45 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Root System Port SNMP DHCP Boot IGMP Snooping VLAN MAC Table GVRP Trunk 802.1x Alarm Configuration Security Bandwidth Diagnostics TFTP Server Firmware Upgrade Reboot Logout Publication date: November, 2005...
Page 46: System Information
You can configure this parameter through the device’s user interface or SNMP. Device name: The name of the switch. User-defined. Default is 065-7726SPOE. System up time: The time accumulated since this switch is powered up. Its format is day, hour, minute, second.
Page 47 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Host IP address: The IP address of the switch. Host MAC address: It is the Ethernet MAC address of the management agent in this switch. Device Port: Show all types and numbers of the port in the switch.
Page 48: Ip Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-1-2. IP Configuration IP configuration is one of the most important configurations in the switch. Without the proper setting, network manager will not be able to manage or view the device.
Page 49 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual IP address: Users can configure the IP settings and fill in new values if users set the DHCP function “Disable”. Then, click <Apply> button to update. When DHCP is disabled, Default: 192.168.1.1 If DHCP is enabled, this field is filled by DHCP server and will not allow user manually set it any more.
Page 50 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual DNS: It is Domain Name Server used to serve the translation between IP address and name address. The switch supports DNS client function to re-route the mnemonic name address to DNS server to get its associated IP address for accessing Internet.
Page 51: Time Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-1-3. Time Configuration The switch provides manual and automatic ways to set the system time via NTP. Manual setting is simple and you just input “Year”, “Month”, “Day”, “Hour”, “Minute”...
Page 52 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual NTP: NTP is Network Time Protocol and is used to sync the network time based Greenwich Mean Time (GMT). If use the NTP mode and select a...
Page 53 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Day Light Saving End : This is used to set when to stop performing the daylight saving time. Mth: Range is 1 ~ 12. Default: 1 Day: Range is 1 ~ 31.
Page 54: Account Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-1-4. Account Configuration In this function, only administrator can create, modify or delete the username and password. Administrator can modify other guest identities’ password without confirming the password but it is necessary to modify the administrator-equivalent identity.
Page 55: Management Security
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-1-5. Management Security Through the management security configuration, the manager can do the strict setup to control the switch and limit the user to access this switch.
Page 56 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Management Security Configuration Function description: The switch offers Management Security Configuration function. With this function, the manager can easily control the mode that the user connects to the switch.
Page 57 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual IP Range: The switch supports two kinds of options for managed valid IP Range, including “Any” and “Custom”. Default is “Any”. In case ” Custom” had been chosen, you can assign the effective IP range. The valid range is 0.0.0.0~255.255.255.255.
Page 58: Virtual Stack
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-1-6. Virtual Stack Function name: Virtual Stack Function description: Virtual Stack Management (VSM) is the group management function. Through the proper configuration of this function, switches in the same LAN will be grouped automatically.
Page 59 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Fig. 3-8 Parameter description: State: It is used for the activation or de-activation of VSM. Default is Enable. Role: The role that you would like the switch to play in the virtual stack. Two types of roles, including master and slave are offered for option.
Page 60: Port Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-2. Port Configuration Four functions, including Port Status, Port Configuration, Simple Counter and Detail Counter are contained in this function folder for port monitor and management. Each of them will be described in detail orderly in the following sections.
Page 61 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Port Status Function Description: Report the latest updated status of all ports in this switch. When any one of the ports in the switch changes its parameter displayed in the page, it will be automatically refreshed the port current status about every 5 seconds.
Page 62 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Speed / Duplex : Display the speed and duplex of all port. There are three speeds 10Mbps, 100Mbps and 1000Mbps supported for TP media, and the duplex supported is half duplex and full duplex.
Page 63 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Fig. 3-11 Parameter description of Port 25 and Port 26: Connector Type: Display the connector type, for instance, UTP, SC, ST, LC, and so Fiber Type: Display the fiber mode, for instance, Multi-Mode, Single-Mode.
Page 64 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Vendor SN (Serial Number): Show the serial number assigned by the manufacturer. Date Code: Show the date this module was made. Temperature: Show the current temperature of module.
Page 65: Port Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-2-2. Port Configuration Port Configuration is applied to change the setting of each port. In this configuration function, you can set/reset the following functions. All of them are described in detail below.
Page 66 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Speed/Duplex: Set the speed and duplex of the port. In speed, 10/100Mbps baud rate is available for Fast Ethernet, Gigabit module in port 25, 26. If the media is 1Gbps fiber, it is always 1000Mbps and the duplex is full only.
Page 67: Simple Counter
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-2-3. Simple Counter The function of Simple Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad.
Page 68 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Rx Packet: The counting number of the packet received. Tx Collision: Number of collisions transmitting frames experienced. Rx Error Packet: Number of bad packets received. Publication date: Oct.., 2005...
Page 69: Detail Counter
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-2-4. Detail Counter The function of Detail Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad.
Page 70 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Rx Unicast Packets: Show the counting number of the received unicast packet. Rx Broadcast Packets: Show the counting number of the received broadcast packet. Rx Multicast Packets: Show the counting number of the received multicast packet.
Page 71 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Packets 512-1023 Octets: Number of 512 ~ 1023-byte frames in good and bad packets received. Packets 1024- 1522 Octets: Number of 1024-1522-byte frames in good and bad packets received.
Page 72: Poe
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-3. PoE Function name: PoE Status Function description: Display the information about the PoE status. Fig. 3-15 Parameter description: Vmain: The volt is supplied by the PoE.
Page 73 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Port No: Port number. Port On: Show whether the port is supplying the power to the PD or not. AC Disconnect Port Off: Port is turned off due to the AC Disconnect function.
Page 74 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: PoE Configuration Function description: In PoE Port Management function, user can configure the settings about PoE. The switch complies with IEEE 802.3af protocol and be capable of detecting automatically that whether the device linked to the port on the switch is PD (Powered Device) or not.
Page 75 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Priority: Three options are offered for the user to choose, including Normal, Low and High. Default is Normal. The switch will stop supplying the power to the port based on the order of the priority Low Normal High in case total power required by all PDs linked to the switch excesses the power limit.
Page 76: Snmp Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-4. SNMP Configuration Any Network Management System (NMS) running the Simple Network Management Protocol (SNMP) can manage the Managed devices equipped with SNMP agent, provided that the Management Information Base (MIB) is installed correctly on the managed devices.
Page 77 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Default SNMP function : Enable Default community name for GET: public Default community name for SET: private Default community name for Trap: public Default Set function : Enable Default trap host IP address: 0.0.0.0...
Page 78: Dhcp Boot
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-5. DHCP Boot The DHCP Boot function is used to spread the request broadcast packet into a bigger time frame to prevent the traffic congestion due to broadcast packets from...
Page 79: Igmp Snooping
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-6. IGMP Snooping The function, IGMP Snooping, is used to establish the multicast groups to forward the multicast packet to the member ports, and, in nature, avoids wasting the bandwidth while IP multicast packets are running over the network.
Page 80 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Parameter description: IGMP snooping mode selection: The switch supports three kinds of IGMP Snooping status, including “Passive”, “Active” and “Disable”. Disable: Set “Disable” mode to disable IGMP Snooping function.
Page 81 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Allowed Group Function description: The Allowed Group function allows the IGMP Snooping to set up the IP multicast table based on user’s specific conditions. IGMP report packets that meet the items you set up will be joined or formed the multicast group.
Page 82 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Add: A new entry of configuration can be created after the allowed group parameters as mentioned above had been setup and then press <Add> button. Edit: The existed entry also can be modified after pressing <Edit> button.
Page 83: Vlan
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-7. VLAN The switch supports Tag-based VLAN (802.1q) and Port-based VLAN Support 256 active VLANs and VLAN ID 1~4094. VLAN configuration is used to partition your LAN into small ones as your demand. Properly configuring it, you can gain not only improving security and increasing performance but greatly reducing VLAN management.
Page 84 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Symmetric Vlan: This is an Ingress Rule (Rule 1, The Ingress Filtering Rule 1 is “forward only packets with VID matching this port’s configured VID”.). For example,...
Page 85: Tag-Based Group
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-7-2. Tag-based Group Function name: Tag-based Group Configuration Function description: It shows the information of existed Tag-based VLAN Groups. You can also easily create, edit and delete a Tag-based VLAN group by pressing <Add>, <Edit>...
Page 86 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Add Group: Input the VLAN name, VID and then choose the member by ticking the check box beside the port No. to create a new Tag-based VLAN. The parameter of Untag stands for an egress rule of the port.
Page 87 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual modify a group’s description, member and untag settings. Publication date: November, 2005 Revision A0.92...
Page 88: Pvid
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-7-3. PVID Function name: PVID Function description: In PVID Setting, user can input VID number to each port. The range of VID number is from 1 to 4094. User also can choose ingress filtering rule (Rule 2) to each port.
Page 89 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Drop Untag: Drop untagged frame. You can configure a given port to accept all frames (Tagged and Untagged) or just receive tagged frame. If the former is the case, then the packets with tagged or untagged will be processed.
Page 90: Port-Based Group
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-7-4. Port-based Group Function name: Port-based Group Configuration Function description: It shows the information of the existed Port-based VLAN Groups. You can easily create, edit and delete a Port-based VLAN group by pressing <Add>, <Edit>...
Page 91 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Add Group: Create a new Port-based VLAN. Input the VLAN name and choose the member by ticking the check box beside the port No., then, press the <Apply>...
Page 92: Mac Table
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-8. MAC Table MAC Table Configuration gathers many functions, including MAC Table Information, MAC Table Maintenance, Static and MAC Alias, which cannot be categorized to some function type. They are described below.
Page 93 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Port: The port that exists in the searched MAC Entry. VID: VLAN Group that MAC Entry exists. State: Display the method that this MAC Entry is built. It may show “Dynamic MAC”...
Page 94 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function Name: MAC Table Maintenance Function Description: This function can allow the user to set up the processing mechanism of MAC Table. An idle MAC address exceeding MAC Address Age-out Time will be removed from the MAC Table.
Page 95 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function Name: Static Setting Function Description: The function of Static is used to configure MAC’s real manners inside of the switch. Three kinds of manners including static, static with destination drop and static with source drop are contained in this function.
Page 96 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Queue (Priority): Set up the priority (0~3) for the MAC. Forwarding Rule (Drop Policy): Static: A MAC address is assigned to a specific port; all of the switch’s traffic sent to this MAC address will be forwarded to this port.
Page 97 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: MAC Alias Function description: MAC Alias function is used to let you assign MAC address a plain English name. This will help you tell which MAC address belongs to which user in the illegal access report.
Page 98 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Parameter description: MAC Address: It is a six-byte long Ethernet hardware address and usually expressed by hex and separated by hyphens. For example, 00 – 40 - C7 - D6 – 00 - 02 Alias: MAC alias name you assign.
Page 99: Gvrp Configuration
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-9. GVRP Configuration GVRP is an application based on Generic Attribute Registration Protocol (GARP), mainly used to automatically and dynamically maintain the group membership information of the VLANs. The GVRP offers the function providing the VLAN registration service through a GARP application.
Page 100 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: GVRP Config Function description: In the function of GVRP Config, it is used to configure each port’s GVRP operation mode, in which there are seven parameters needed to be configured described below.
Page 101 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Normal: It is Normal Registration. The Registrar responds normally to incoming GARP messages. The default setting is Normal. Fixed: It is Registration Fixed. The Registrar ignores all GARP messages, and all members remain in the registered (IN) state.
Page 102 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: GVRP Counter Function description: All GVRP counters are mainly divided into Received and Transmitted two categories to let you monitor the GVRP actions. Actually, they are GARP packets.
Page 103 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual LeaveEmpty Message Packets: Number of GARP BPDU with Leave Empty message is received by the GARP application. Empty Message Packets: Number of GARP BPDU with Empty message is received by the GARP application.
Page 104 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: GVRP Group Information Function description: To show the dynamic group members and their information. Parameter description: Current Dynamic Group Number: The number of GVRP group that are created currently.
Page 105: Stp Configuration
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-10. STP Configuration The Spanning Tree Protocol (STP) is a standardized method (IEEE 802.1D) for avoiding loops in switched networks. When STP is enabled, ensure that only one path is active between any two nodes on the network at a time.
Page 106 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual All bridges in the LAN will re-learn and determine which the root bridge is. Maximum Age time is assigned by root bridge in unit of seconds. Default is 20 seconds.
Page 107: Stp Configuration
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-10-2. STP Configuration The STP, Spanning Tree Protocol, actually includes RSTP. In the Spanning Tree Configuration, there are six parameters open for the user to configure as the user prefers.
Page 108 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Forward Delay: You can set the root bridge forward delay time. This figure is set by root bridge only. The forward delay time is defined as the time spent from Listening state moved to Learning state and also from Learning state moved to Forwarding state of a port in bridge.
Page 109: Stp Port Configuration
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-10-3. STP Port Configuration Function name: STP Port Setting Function description: In the STP Port Setting, one item selection and five parameters settings are offered for user’s setup. User can disable and enable each port by selecting each Port Status item.
Page 110 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 802.1w RSTP recommended value: (Valid range: 1 – 200,000,000) 10 Mbps : 2,000,000 100 Mbps : 200,000 1 Gbps : 20,000 Default: 0 Priority: Priority here means Port Priority. Port Priority and Port Number are mixed to form the Port ID.
Page 111 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Default: Auto Publication date: November, 2005 Revision A0.92...
Page 112 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual M Check: Migration Check. It forces the port sending out an RSTP BPDU instead of a legacy STP BPDU at the next transmission. The only benefit of this operation is to make the port quickly get back to act as an RSTP port.
Page 113: Trunking Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-11. Trunking Configuration The Port Trunking Configuration is used to configure the settings of Link Aggregation. You can bundle more than one port with the same speed, full duplex and the same MAC to be a single logical port, thus the logical port aggregates the bandwidth of these ports.
Page 114 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Per Trunking Group supports a maximum of 4 ready member-ports. Please note that some decisions will automatically be made by the system while you are configuring your trunking ports. Trunk Setting Rules are listed below:...
Page 115 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Port Setting/Status Function description: Port setting/status is used to configure the trunk property of each and every port in the switch system. Parameter description: Method: This determines the method a port uses to aggregate with other ports.
Page 116 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Aggtr: Aggtr is an abbreviation of “aggregator”. Every port is also an aggregator, and its own aggregator ID is the same as its own Port No. We can regard an aggregator as a representative of a trunking group.
Page 117 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Aggregator View Function description: To display the current port trunking information from the aggregator point of view. Parameter description: Aggregator: It shows the aggregator ID (from 1 to 26) of every port. In fact, every port is also an aggregator, and its own aggregator ID is the same as its own Port No..
Page 118 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: LACP Detail (LACP Aggregator Detailed Information) Function description: Show the detailed information of the LACP trunking group. Parameter description: Actor: The switch you are watching on.
Page 119 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Publication date: November, 2005 Revision A0.92...
Page 120 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: LACP System Configuration Function description: It is used to set the priority part of the LACP system ID. LACP will only aggregate together the ports whose peer link partners are all on a single system.
Page 121: Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-12. 802.1x Configuration 802.1x port-based network access control provides a method to restrict users to access network resources via authenticating user’s information. This restricts users from gaining access to the network resources through an 802.1x-enabled port without authentication.
Page 122 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual The overview of operation flow for the Fig. 3-43 is quite simple. When Supplicant PAE issues a request to Authenticator PAE, Authenticator and Supplicant exchange an authentication message. Then, Authenticator passes the request to RADIUS server to verify.
Page 123 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Authentication server Fig. 3-44 Authenticator Supplicant A The Fig. 3-45 shows the procedure of 802.1x authentication. There are steps for the login based on 802.1x port access control management. The protocol used in the right side is EAPOL and the left side is EAP.
Page 124 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual If user ID and password is correct, the authentication server will send a Radius-Access-Accept to the authenticator. If not correct, the authentication server will send a Radius-Access-Reject.
Page 125 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Only MultiHost 802.1X is the type of authentication supported in the switch. In this mode, for the devices connected to this port, once a supplicant is authorized, the devices connected to this port can access the network resource through this port.
Page 126 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: 802.1x State Setting Function description: This function is used to configure the global parameters for RADIUS authentication in 802.1x port security application. Parameter description: Radius Server: RADIUS server IP address for authentication.
Page 127 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: 802.1x Mode Setting Function description: Set the operation mode of 802.1X for each port. In this device, it supports only Multi-host operation mode. Parameter description: Port Number: Indicate which port is selected to configure the 802.1x operation mode.
Page 128 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Port Security Management Function description: Shows each port status. In Multihost mode, it shows the port number and its status, authorized or unauthorized. Parameter description: Disable Mode: When selecting Disable mode for a port in the function 802.1X Port Mode...
Page 129 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Param. Setting Function description: This function is used to configure the parameters for each port in 802.1x port security application. Refer to the following parameters description for details.
Page 130 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual reAuthEnabled: Choose whether regular authentication will take place in this port. Default: ON reAuthPeriod (1-65535 s): A non-zero number seconds between the periodic re-authentication of the supplicant.
Page 131: Alarm Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-13. Alarm Configuration Alarm Configuration Events Configuration Email/SMS Configuration Function name: Events Configuration Function description: The Trap Events Configuration function is used to enable the switch to send out the trap information while pre-defined trap events occurred.
Page 132 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Fig. 3-50 Function name: Email/SMS Configuration Function description: Alarm configuration is used to configure the persons who should receive the alarm message via either email or SMS, or both. It depends on your settings.
Page 133 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Parameter description: Email: Mail Server: the IP address of the server transferring your email. Username: your username on the mail server. Password: your password on the mail server.
Page 134: Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-14. Configuration The switch supports three copies of configuration, including the default configuration, working configuration and user configuration for your configuration management. All of them are listed and described below respectively.
Page 135: Save/Restore
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-14-1. Save/Restore Function name: Save As Start Configuration Function description: Save the current configuration as a start configuration file in flash memory. Fig. 3-53 Function name: Save As User Configuration Function description: Save the current configuration as a user configuration file in flash memory.
Page 136 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Restore Default Configuration (includes default IP address) Function description: Restore Default Configuration function can retrieve the ex-factory setting to replace the start configuration. And the IP address of the switch will also be restored to 192.168.1.1.
Page 137 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Restore User Configuration Function description: Restore User Configuration function can retrieve the previous confirmed working configuration stored in the flash memory to update start configuration.
Page 138: Config File
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-14-2. Config File Function name: Config File Function description: With this function, user can back up or reload the config files of Save As Start or Save As User via TFTP.
Page 139: Security
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-15. Security Function name: Mirror Configuration Function description: Mirror Configuration is to monitor the traffic of the network. For example, we assume that Port A and Port B are Monitoring Port and Monitored Port respectively, thus, the traffic received by Port B will be copied to Port A for monitoring.
Page 140 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Isolated Group Function description: Isolated Group function can let the port be independent of other ports in the Isolated group, and the communication is also forbidden between these ports.
Page 141 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Restricted Group Function description: The function of the Restricted Group can decide the direction of transmitting packets for the specific port. The packets received by the port with the “Ingress”...
Page 142: Bandwidth Management
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-16. Bandwidth Management Function name: Ingress Bandwidth Setting Function description: Ingress Bandwidth Setting function is used to set up the limit of Ingress bandwidth for each port.
Page 143 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Egress Bandwidth Setting Function description: Egress Bandwidth Setting function is used to set up the limit of Egress bandwidth for each port. Fig. 3-63 Parameter description: Port No.:...
Page 144 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Storm Setting Function description: Bandwidth Management function is used to set up the limit of Ingress and Egress bandwidth for each port. Fig. 3-64 Parameter description:...
Page 145 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Storm Rate : Set up the limit of bandwidth for storm type you choose. Valid value of the storm rate ranges from 1-100 with the minimum unit of 1. And only integer is acceptable.
Page 146: Qos(Quality Of Service) Configuration
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-17. QoS(Quality of Service) Configuration The switch supports 5 kinds of QoS, are as follows, MAC Priority, 802.1p Priority, IP TOS Priority, and DiffServ DSCP Priority. Port Based Priority has a special name called VIP Port in the switch.
Page 147 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual The QoS functions as we mentioned above are able to enabled at the same time. But, the following precedence will decide whether these functions work or not.
Page 148 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: QoS Global Setting Function description: When you want to use QoS function, please enable QoS Mode in advance. Then you can use MAC Priority, 802.1p Priority, IP TOS Priority, DiffServ DSCP Priority, or VIP Port functions and take effect.
Page 149 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: VIP Port Setting Function description: When the port is set as VIP Port, the packets enter this port and will have highest transmitting priority. For example, as you choose port 2 is VIP Port, simultaneously transmit packets from port 2 and port 3 to port 1 at speed of 100MB and let congestion happen.
Page 150 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: 802.1p Setting Function description: This function will affect the priority of VLAN tag. Based on priority of VLAN tag, it can arrange 0~8 priorities, priorities can map to 4 queues of the switch (queue 0~3) and possess different bandwidth distribution according to your weight setting.
Page 151 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: D-Type TOS Function description: IP TOS Priority affect TOS fields of IP header, you can find it has 8-bit SERVICE TYPE field that specifies how the datagram should be handled. The...
Page 152 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: T-Type TOS Function description: IP TOS Priority affect TOS fields of IP header, you can find it has 8-bit SERVICE TYPE field that specifies how the datagram should be handled. The...
Page 153 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: R-Type TOS Function description: IP TOS Priority affect TOS fields of IP header, you can find it has 8-bit SERVICE TYPE field that specifies how the datagram should be handled. The...
Page 154 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: M-Type TOS Function description: IP TOS Priority affect TOS fields of IP header, you can find it has 8-bit SERVICE TYPE field that specifies how the datagram should be handled. The...
Page 155 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: DSCP Setting Function description: In the late 1990s, the IETF redefined the meaning of the 8-bit SERVICE TYPE field to accommodate a set of differentiated services (DS). Under the differentiated services interpretation, the first six bits comprise a codepoint, which is sometimes abbreviated DSCP, and the last two bits are left unused.
Page 156: Diagnostics
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-18. Diagnostics Three functions, including Diagnostics, Loopback Test and Ping Test are contained in this function folder for device self-diagnostics. Each of them will be described in detail orderly in the following sections.
Page 157 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Loopback Test Function description: In the Loopback Test function, there are two different loopback tests. One is Internal Loopback Test and the other is External Loopback Test. The former test function will not send the test signal outside the switch box.
Page 158 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Function name: Ping Test Function description: Ping Test function is a tool for detecting if the target device is alive or not through ICMP protocol which abounds with report messages. The switch provides Ping Test function to let you know that if the target device is available or not.
Page 159: Tftp Server
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-19. TFTP Server Function name: TFTP Server Function description: Set up IP address of TFTP server. Parameter description: Specify the IP address where the TFTP server locates. Fill in the IP address of your TFTP server, then press <Apply>...
Page 160: Log
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-20. Log This function shows the log data. The switch provides system log data for users. There are 16 private trap logs, 5 public trap logs. The switch supports total 120 log entries.
Page 161 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Upload Log: Upload log data through tftp. Clear Log: Clear log data. Publication date: November, 2005 Revision A0.92...
Page 162: Firmware Upgrade
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-21. Firmware Upgrade Software upgrade tool is used to help upgrade the software function in order to fix or improve the function. The switch provides a TFTP client for software upgrade.
Page 163: Reboot
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-22. Reboot We offer you many ways to reboot the switch, including power up, hardware reset and software reset. You can press the RESET button in the front panel to reset the switch.
Page 164: Logout
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 3-23. Logout You can manually logout by performing Logout function. In the switch, it provides another way to logout. You can configure it to logout automatically. Function name:...
Page 165: Chapter 4. Operation Of Cli Management
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 4. Operation of CLI Management 4-1. CLI Management Refer to Chapter 2 for basic installation. The following description is the brief of the network connection. -- Locate the correct DB-9 null modem cable with female DB-9 connector. Null modem cable comes with the management switch.
Page 166 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 065-7726SPoE 065-7726SPoE# Fig. 4-1 065-7726SPoE# Fig. 4-2 Publication date: Oct.., 2005 Revision A1...
Page 167: Commands Of Cli
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 4-2. Commands of CLI To see the commands of the mode, please input “?” after the prompt, then all commands will be listed in the screen. All commands can be divided into two categories, including global commands and local commands.
Page 168: Global Commands Of Cli
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 4-2-1. Global Commands of CLI Syntax: Description: Back to the top mode. When you enter this command, your current position would move to the top mode. If you use this command in the top mode, you are still in the position of the top mode.
Page 169 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual help Syntax: help Description: To show available commands. Some commands are the combination of more than two words. When you enter this command, the CLI would show the complete commands. Besides, the command would help you classify the commands between the local commands and the global ones.
Page 170 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual history Syntax: history [#] Description: To show a list of previous commands that you had ever run. When you enter this command, the CLI would show a list of commands which you had typed before.
Page 171 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual logout Syntax: logout Description: When you enter this command via Telnet connection, you would logout the system and disconnect. If you connect the system through direct serial port with RS-232 cable, you would logout the system and be back to the initial login prompt when you run this command.
Page 172 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual restore user Syntax: restore user Description: To restore the startup configuration as user defined configuration. If restoring default successfully, the CLI would prompt if reboot immediately or not. If you press Y or y, the system would reboot immediately;...
Page 173 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual save user Syntax: save user Description: To save the current configuration as the user-defined configuration. When you enter this command, the CLI would save your current configuration into the non-volatile FLASH as user-defined configuration.
Page 174: Local Commands Of Cli
<port range>: syntax 1,5-7, available from 1 to 26 <times>: max-times, range 1-10 Possible value: <port range> : 1 to 26 <times> : 1-10, default is 2 Example: 065-7726SPOE(802.1x)# set max-request 2 2 set mode Syntax: set mode <port-range> <mode> Description: To set up the 802.1X mode of each port.
Page 175 2:Auto Possible value: <port range> : 1 to 26 <authorized> : 0,1 or 2 Example: 065-7726SPOE(802.1x)# set port-control 2 2 set quiet-period Syntax: set quiet-period <port-range> <sec> Description: A timer used by the Authenticator state machine to define periods of time during when it will not attempt to acquire a Supplicant.
Page 176 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 065-7726SPOE(802.1x)# set reAuthEnabled 2 1 set reAuthMax Syntax: set reAuthMax <port-range> <max> Description: The number of reauthentication attempts that are permitted before the port becomes Unauthorized. Argument: <port range>...
Page 177 <secret-key> : set up the value of secret-key, and the length of secret-key is from 1 to 31 Possible value: <port-number> : 1~65535, default 1812 Example: 065-7726SPOE(802.1x)# set state 192.168.1.115 1812 WinRadius set suppTimeout Syntax: set suppTimeout <port-range> <sec> Description:...
Page 178 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual <sec> : 1-65535, default is 30 Example: 065-7726SPOE(802.1x)# set txPeriod 2 30 show mode Syntax: show mode Description: To display the mode of each port. Argument: None.
Page 179 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual serverTimeout : 30 Publication date: November, 2005 Revision A0.92...
Page 180 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show security Syntax: show security Description: To display the status of each port. authentication Argument: None. Possible value: None. Example: 065-7726SPOE(802.1x)# show security Port Mode Status ====== ============ ==============...
Page 181 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual account Syntax: add <name> Description: To create a new guest user. When you create a new guest user, you must type in password and confirm password. Argument: <name>...
Page 182 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual modify Syntax: modify <name> Description: To change the username and password of an existing account. Argument: <name> : existing user account Possible value: None. Example: 065-7726SPOE(account)# modify aaaaa username/password: the length is from 5 to 15.
Page 183 Description: To set up the email address. Argument: <#> : email address number, range: 1 to 6 <mail address> : email address Possible value: <#>: 1 to 6 Example: 065-7726SPOE(alarm-email)# set mail-address 1 abc@mail.abc.com Publication date: November, 2005 Revision A0.92...
Page 184 To set up the IP address of the email server. Argument: <ip>:email server ip address or domain name Possible value: None. Example: 065-7726SPOE(alarm-email)# set server 192.168.1.6 set user Syntax: set user <username> Description: To set up the account of the email server.
Page 185 To disable email, sms and trap of events. Argument: <range>:del the range of email, sms and trap of events, syntax 1,5-7 Possible value: <range>: 1~22 Example: 065-7726SPOE(alarm-events)# del all 1-3 del email Syntax: del email <range> Description: To disable the email of the events.
Page 186 To disable the trap of the events. Argument: <range>:del the range of trap, syntax 1,5-7 Possible value: <range>: 1~22 Example: 065-7726SPOE(alarm-events)# del trap 1-3 set all Syntax: set all <range> Description: To enable email, sms and trap of events. Argument: <range>:set the range of email, sms and trap of events, syntax 1,5-7...
Page 187 Description: To enable the sms of the events. Argument: <range>:set the range of sms, syntax 1,5-7 Possible value: <range>: 1~22 Example: 065-7726SPOE(alarm-events)# set sms 1-3 set trap Syntax: set trap <range> Description: To enable the trap of the events. Argument: <range>:set the range of trap, syntax 1,5-7...
Page 188 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show Syntax: show Description: The Show here is used to display the configuration of alarm event. Argument: None. Possible value: None. Example: 065-7726SPOE(alarm-events)# show Events Email SMS Trap...
Page 189 To delete sms phone number. Argument: <#>: mobile phone number, range: 1 to 6 Possible value: <#>: 1 to 6 Example: 065-7726SPOE(alarm-sms)# del phone-number 3 del server-user Syntax: del server-user Description: To delete sms server, user account and password. Argument: None.
Page 190 Argument: <#>: mobile phone number, range: 1 to 6 <phone-number>: phone number Possible value: <#>: 1 to 6 Example: 065-7726SPOE(alarm-sms)# set phone-number 1 0968777777 set server Syntax: set server <ip> Description: To set up the IP address of sms server.
Page 191 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show Syntax: show Description: To display the configuration of SMS trap event. Argument: None. Possible value: None. Example: 065-7726SPOE(alarm-sms)# show SMS Server : 192.168.1.7 Username : ABC...
Page 192 1-24: 66-102400(Kb); port 25-26: 66-1024000(Kb) Possible value: <range>: 1 to 26 <data_rate>: 66-102400(Kb) for port 1-24; 66-1024000(Kb) for port 25-26 Example: 065-7726SPOE(bandwidth)# set egress-rate 1-16 299 set ingress-rate Syntax: set ingress-rate <range> <data_rate> Description: To set up the ingress-rate of the ports.
Page 193 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 065-7726SPOE(bandwidth)# set ingress-rate 1-16 100 set storm-rate Syntax: set storm-rate <range> <data_rate> Description: To set up the storm-rate of the ports. Argument: <range>:syntax: 1,3-5, available from 1 to 5...
Page 194 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Type: Disable Rate: 100 % Publication date: Oct.., 2005 Revision A1...
Page 195 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual config-file export start Syntax: export start Description: To run the export start function. Argument: None. Possible value: None. Example: 065-7726SPOE(config-file)# export start Export successful. export user-conf Syntax:...
Page 196 To set up the file path and filename that user would like to export. Argument: <filepath>:filepath and filename Possible value: <filepath>:filepath and filename Example: 065-7726SPOE(config-file)# set export-path log/21511.txt set import-path Syntax: set import-path <filepath> Description: To set up the filepath and filename that user would like to import.
Page 197 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show Syntax: show Description: To display the information of the config file. Argument: None. Possible value: None. Example: 065-7726SPOE(config-file)# show TFTP Server IP Address: 192.168.3.111 Export Path and Filename: log/21511.txt Import Path and Filename: log/21511.txt...
Page 198 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual diag diag Syntax: diag Description: Diag is used to test whether EEPROM, UART, DRAM and Flash is normal or not. Argument: None. Possible value: None. Example: 065-7726SPOE(diag)# diag...
Page 199 To set up the image file that will be upgraded. Argument: <filepath>: upgrade file path and name Possible value: <filepath>: upgrade file path and name Example: 065-7726SPOE(firmware)# set upgrade-path FEL2SW26_ES2126_v2.05.img show Syntax: show Description: To display the information of tftp server and upgrade-path and file name.
Page 200 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual gvrp disable Syntax: disable Description: To disable the gvrp function Argument: None. Possible value: None. Example: 065-7726SPOE(gvrp)# disable enable Syntax: enable Description: To enable the gvrp function.
Page 201 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 065-7726SPOE(gvrp)# group 2 065-7726SPOE(gvrp-group-2)# set applicant 1-6 non-participant 065-7726SPOE(gvrp-group-2)# show GVRP group VID: 2 Port Applicant Registrar ---- --------------- --------- Non-Participant Normal Non-Participant Normal Non-Participant Normal Non-Participant Normal...
Page 202 <normal>: set applicant as normal mode <non-participant>: set applicant as non-participant mode Possible value: <range>: 1 to 26 <normal|non-participant>: normal or non-participant Example: 065-7726SPOE(gvrp)# set applicant 1-10 non-participant set registrar Syntax: set registrar <range> <normal|fixed|forbidden> Description: To set default registrar mode for each port.
Page 203 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Example: 065-7726SPOE(gvrp)# set restricted 1-10 enable 065-7726SPOE(gvrp)# show config GVRP state: Enable Port Join Time Leave Time LeaveAll Time Applicant Registrar Restricted ---- --------- ---------- ------------- --------------- --------- ----------...
Page 204 Leave Time must equal double Join Time at least. Possible value: <range> : 1 to 26 <join>: 20 to 100 <leave>: 60 to 300 <leaveall>: 1000 to 5000 Example: 065-7726SPOE(gvrp)# set timer 2-8 25 80 2000 show config Syntax: show config Description: To display the gvrp configuration. Argument: None.
Page 205 To show counter of the port. Argument: <port>: port number, available from 1 to 26 Possible value: <port>: 1 to 26 Example: 065-7726SPOE(gvrp)# show counter 2 GVRP Counter port: 2 Counter Name Received Transmitted -------------------- -------- ----------- Total GVRP Packets...
Page 206 <port-range>: syntax 1,5-7, available from 1 to 26 Possible value: <ip-multicast>: ex: 224.1.1.1-225.2.3.3 or any <vid>: 1-4094 or any <port-range>: 1 to 26 Example: 065-7726SPOE(igmp-snooping)# add allowed-group 224.1.1.1-225.2.3.3 100 1-10 del allowed-group Syntax: del allowed-group <index> Description: To remove the entry of allowed IP multicast group Argument: <index>: the index of the allowed-group.
Page 207 To set up the mode of IGMP Snooping. Argument: <status>: 0:disable, 1:active, 2:passive Possible value: <status>: 0,1or 2 Example: 065-7726SPOE(igmp-snooping)# set mode 2 show igmp-snooping Syntax: show igmp-snooping Description: To display IGMP snooping mode and allowed IP multicast entry. Argument: None.
Page 208 To enable the system DHCP function and set DNS server via manual or auto mode. Argument: <manual|auto> : set DNS by using manual or auto mode. Possible value: <manual|auto> : manual or auto Example: 065-7726SPOE(ip)# enable dhcp manual set dns Syntax: set dns <ip> Description: To set the IP address of DNS server.
Page 209 Possible value: <ip> : 192.168.1.1 or others <mask> : 255.255.255.0 or others <gateway> : 192.168.1.253 or others Example: 065-7726SPOE(ip)# set ip 192.168.1.2 255.255.255.0 192.168.1.253 show Syntax: show Description: To display the system’s DHCP function state, IP address, subnet mask, default gateway, DNS mode, DNS server IP address and current IP address.
Page 210 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual clear Syntax: clear Description: To clear the log data. Argument: None. Possible value: None. Example: 065-7726SPOE(log)# clear disable auto-upload Syntax: disable auto-upload Description: To disable the auto-upload function.
Page 211 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show Syntax: show Description: To show a list of trap log events. When any of log events happens, it will be recorded and using show command in log function to query. Up to 120 log records are supported.
Page 212 <mac> : mac address, format: 00-02-03-04-05-06 <alias> : mac alias name, max. 15 characters Possible value: <mac> : mac address <alias> : max. 15 characters Example: 065-7726SPOE(mac-table-alias)# set 00-44-33-44-55-44 www show Syntax: show Description: To display the mac alias entry.
Page 213 <vid> : vlan id, from 1 to 4094; '?' as don't care, 0 as untagged Possible value: <port> : 1 to 26 <vid> : 0, 1 ~4094 Example: 065-7726SPOE(mac-table-information)# search 1-26 ??-??-??-??-??-?? ? MAC Table List Alias MAC Address Port VID State...
Page 214 0 to 8191; 0 for learning disabled Possible value: <port> : 1 to 24 <num>: 0 to 8191 Example: 065-7726SPOE(mac-table-maintain)# set learning 5 100 show Syntax: show Description: To display the settings of MAC table ageout time and the learning limit of each port.
Page 215 <port> : forwarded destination port, form 1 to 26 Possible value: <vid>: 1 to 4094 <queue>: 0 to 3 <rule>: 0 to 2 <port>: 1 to 26 Example: 065-7726SPOE(mac-table-static-mac)# add 00-22-44-55-66-77 1 0 0 6 Publication date: November, 2005 Revision A0.92...
Page 216 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Syntax: del <mac> Description: To remove the static mac entry. Argument: <mac> : mac address, format: 00-02-03-04-05-06 Possible value: <mac> : mac address Example: 065-7726SPOE(mac-table-static-mac)# del 00-02-03-04-05-06...
Page 217 [<type> <value>] For example, h(ttp),s(nmp),t(elnet) or any. <action> <value> No default and it must be set. Example: 065-7726SPOE(management-add)# set name Mary vid 20 ip 192.168.1.1- 192.168.1.90 port 2-5,8 type h,s action a 065-7726SPOE(management-add)# show #: 1 Name : Mary VlanID : 20 IP : 192.168.1.1-192.168.1.90...
Page 218 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual delete Syntax: delete # Description: To delete a specific record or range. Argument: [#]: a specific or range management security entry(s) Possible value: None. Example: 065-7726SPOE(management)# show...
Page 219 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Example: 065-7726SPOE(management)# edit 1 065-7726SPOE(management-edit-1)# set name Tom vid 2 ip 192.168.1.30- 192.168.1.80 port 1-2 type s action d 065-7726SPOE(management-edit-1)# show #: 1 Name : Tom VlanID : 2 IP : 192.168.1.30-192.168.1.80...
Page 220 <priority>: set priority as 0:Low, 1:Normal, 2:High Possible value: <port range>: 1 to 24 <priority>: 0, 1 or 2 Example: 065-7726SPOE(poe)# set priority 1-12 2 set state Syntax: set state <port-range> <state> Description: To set the PoE state on ports.
Page 221 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show Syntax: show Description: To display the PoE status. Argument: None Possible value: None Example: 065-7726SPOE(poe)# show Vmain : 48.3 V Imain : 0.0 A Pconsume : 0.0 W...
Page 222 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Port Status State Priority Power(W) Current(mA) Class ---- ------ ------- -------- -------- ----------- ----- 1 Normal Enable Normal 2 Normal Enable Normal 3 Normal Enable Normal 4 Normal Enable...
Page 223 To disable the communication capability of the port. Argument: <range>: port range, syntax 1,5-7, available from 1 to 26 Possible value: <range>: 1 ~ 26 Example: 065-7726SPOE(port)# disable state 12 enable state Syntax: enable state <range> Description: To enable the communication capability of the port.
Page 224 : set to half duplex full : set to full duplex Possible value: <range>: 1 to 26 <port-speed> : auto, 10, 100, 1000 <port-duplex> : full, half Example: 065-7726SPOE(port)# set speed-duplex 8 100 full Publication date: Oct.., 2005 Revision A1...
Page 225 To display the detailed counting number of each port’s traffic. Argument: <#> : port, available from 1 to 26 Possible value: <#>:1 ~ 26 Example: 065-7726SPOE(port)# show detail-counter 6 show media Syntax: show media <port> Description: To display the module 25 or 26 information.
Page 226 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Port 25 Fiber Media Information --------------------------------------------------------------------- Connector Type : SFP - LC Fiber Type : Multi-mode (MM) Tx Central Wavelength : 850 Baud Rate : 1G Vendor OUI...
Page 227 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show status Syntax: show status Description: To display the port’s current status. Argument: None. Possible value: None. Example: 065-7726SPOE(port)# show status Port Media Link State Auto Nego. Speed/Duplex Rx Pause Tx Pause...
Page 228 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual disable 1p Syntax: disable 1p Description: To disable 802.1p qos. Argument: None. Possible value: None. Example: 065-7726SPOE(qos)# disable 1p disable dscp Syntax: disable dscp Description: To disable IP DSCP qos.
Page 229 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual disable tos Syntax: disable tos Description: To disable IP TOS qos. Argument: None. Possible value: None. Example: 065-7726SPOE(qos)# disable tos enable 1p Syntax: enable 1p Description: To enable 802.1p qos.
Page 230 You don't need to use all of queue, but must assign queue in order. Syntax: 1,2 or 2,5-7, available from 0 to 63. Possible value: <priority>: 0 to 63 Example: 065-7726SPOE(qos)# set dscp q0 2 q1 2 q2 2 q3 3 Publication date: Oct.., 2005 Revision A1...
Page 231 You don't need to use all of queues, but must assign queues in order. Syntax: 1,2 or 2,5-7, available from 0 to 7. Possible value: <priority>: 0 to 7. Example: 065-7726SPOE(qos)# set pri-tag q0 0 q1 2 q3 4 set sche Syntax: set sche <wrr|strict> <wrr_0> <wrr_1> <wrr_2> <wrr_3> Description: To set qos schedule and weight for 4 queues.
Page 232 PoE Managed Switch User Manual Possible value: <type_value>: 0~3 <priority>: 0 to 7. Example: 065-7726SPOE(qos)# set tos 0 q0 1 q1 2 q2 4 q3 6 set vip Syntax: set vip <port_range> <mode> Description: To set vip port for strict priority.
Page 233 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual DiffServ Queue DiffServ Queue DiffServ Queue DiffServ Queue ---------- ------- ---------- ------- ---------- ------- ---------- ------ show port Syntax: show port Description: To show VIP port configuration.
Page 234 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show priority-tag Syntax: show priority-tag Description: To show 802.1p Qos configuration. Argument: None. Possible value: None. Example: 065-7726SPOE(qos)# show priority-tag 802.1p priority ==================== Global QoS mode: Enable QoS Enable 802.1p Priority...
Page 235 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show tos Syntax: show tos Description: To show IP tos Qos configuration. Argument: none Possible value: none Example: 065-7726SPOE(qos)# show tos ip tos classification ==================== Global QoS mode: Enable QoS Disable 802.1p Priority...
Page 236 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual reboot reboot Syntax: reboot Description: To reboot the system. Argument: None. Possible value: None. Example: 065-7726SPOE# reboot security <<isolated-group>> Syntax: set <port> Description: To set up the function of the isolated group.
Page 237 <egress>: monitored egress port; range syntax: 1,5-7, available from 0 to 26 set ingress/egress to 0 as ingress/egress disabled Possible value: <ingress>: 0 to 26 <egress>: 0 to 26 Example: 065-7726SPOE(security-mirror)# set 1 4 2-3 Publication date: November, 2005 Revision A0.92...
Page 238 <egress>: egress group port; range syntax: 1,5-7, available from 0 to 26 set ingress or egress to 0 as disabled Possible value: <ingress>: 0 to 26 <egress>: 0 to 26 Example: 065-7726SPOE(security-restricted-group)# set 5 8-10 show Syntax: show Description: To display the current setting status of restricted group.
Page 239 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual snmp disable Syntax: disable set-community disable snmp Description: The Disable here is used for the de-activation of snmp or set-community. Argument: None. Possible value: None. Example: 065-7726SPOE(snmp)# disable set-community...
Page 240 Possible value: <trap number> : 1 to 6 <port> :1~65535 Example: 065-7726SPOE(snmp)# set get-community public 065-7726SPOE(snmp)# set set-community private 065-7726SPOE(snmp)# set trap 1 192.168.1.1 162 public show Syntax: show Description: The Show here is to display the configuration of SNMP.
Page 241 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual MCheck Syntax: MCheck <range> Description: To force the port to transmit RST BPDUs. Argument: <range>: syntax 1,5-7, available from 1 to 26 Possible value: <range>: 1 to 26...
Page 242 <path cost>: 0, 1-200000000. <priority> : 0 to 240 <edge_port> : yes / no <admin p2p>: auto / true / false Example: 065-7726SPOE(stp)# set port 1-16 0 128 yes auto set version Syntax: set version <stp|rstp> Description: To set up the version of STP.
Page 243 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 065-7726SPOE(stp)# set version rstp show config Syntax: show config Description: To display the STP configuration data. Argument: None. Possible value: None. Example: 065-7726SPOE(stp)# show config STP State Configuration :...
Page 244 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show status Syntax: show status Description: To display of the status of STP. Argument: None. Possible value: None. Example: 065-7726SPOE(stp)# show status STP Status : STP State...
Page 245 Argument: <contact>:string length up to 40 characters. Possible value: <contact>: A, b, c, d, ... ,z and 1, 2, 3, …. etc. Example: 065-7726SPOE(system)# set contact Taipei set device-name Syntax: set device-name <device-name> Description: To set the device name description of the switch.
Page 246 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show Syntax: show Description: To display the basic information of the switch. Argument: None. Possible value: None. Example: 065-7726SPOE(system)# show Model Name : 065-7726SPOE System Description : 24-Port 10/100BaseT/TX Managed PoE Switch...
Page 247 To set up the IP address of tftp server. Argument: <ip>: the IP address of tftp server Possible value: <ip>: tftp server IP Example: 065-7726SPOE(tftp)# set server 192.168.3.111 show Syntax: show Description: To display the information of tftp server. Argument:...
Page 248 <HH> : (00-23) <mm> : (01-12) <dd> : (01-31) <hh> : (00-23) Example: 065-7726SPOE(time)# set daylightsaving 3 10/12/01 11/12/01 set manual Syntax: set manual <YYYY/MM/DD> <hh:mm:ss> Description: To set up the current time manually. Argument: <YYYY> : Year (2000-2036) <MM>...
Page 249 To set up the current time via NTP server. Argument: <ip>: ntp server ip address or domain name <timezone>: time zone (GMT), range: -12 to +13 Possible value: <timezone>: -12,-11…,0,1…,13 Example: 065-7726SPOE(time)# set ntp clock.via.net 8 Synchronizing...(1) Synchronization success show Syntax: show Description: To show the time configuration, including “Current Time”, “NTP Server”,”...
Page 250 To remove the trunk port. Argument: <port-range> : syntax 1,5-7, available from 1 to 26 Possible value: <port-range> : 1 to 26 Example: 065-7726SPOE(trunk)# del trunk 1 set hash Syntax: set hash <method> Description: To set up trunk hash method.
Page 251 : set the LACP to passive mode Possible value: <port-range> : 1 to 26 <method>: static or lacp <group>: 1-3. <active LACP>: active or passive Example: 065-7726SPOE(trunk)# set trunk 2-5 lacp 1 active show aggtr-view Syntax: show aggtr-view Description: To display the aggregator list. Argument: None.
Page 252 To display the detailed information of the LACP trunk group. Argument: <aggtr> : aggregator, available from 1 to 26 Possible value: <aggtr> : 1 to 26 Example: 065-7726SPOE(trunk)# show lacp-detail 2 Aggregator 2 Information: Actor Partner --------------------------------- --------------------------------- System Priority...
Page 253 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show status Syntax: show status Description: To display the aggregator status and the settings of each port. Argument: None. Possible value: None. Example: 065-7726SPOE(trunk)# show status Trunk Port Setting...
Page 254 Description: To delete the port-based vlan group. Argument: <name>: port-vlan name Possible value: <name>: port-vlan name Example: 065-7726SPOE(vlan)# del port-group vlan-2 del tag-group Syntax: del tag-group <vid> Description: To delete the tag-based vlan group. Argument: <vid>: vlan ID, available from 1 to 4094 Possible value: <vid>: 1 to 4094...
Page 255 Argument: <port_range>: which port(s) you want not to drop untagged frames. Syntax: 1,5-7, available from 1 to 26 Possible value: <port_range>: 1 to 26 Example: 065-7726SPOE(vlan)# disable drop-untag 2,4,5-7 disable svl Syntax: disable svl Description: To enable Independent VLAN Learning.
Page 256 Argument: <port_range>: which port(s) you want to drop untagged frames. Syntax: 1,5-7, available from 1 to 26 Possible value: <port_range>: 1 to 26 Example: 065-7726SPOE(vlan)# enable drop-untag 2,4,5-7 enable svl Syntax: enable svl Description: To enable Shared VLAN Learning. Argument: None.
Page 257 To add or edit a port-based vlan group. Argument: <name>: port-vlan name <range>: vlan group members, syntax: 1,5-7, available from 1 to 26 Possible value: <range>: 1 to 26 Example: 065-7726SPOE(vlan)# set port-group vlan-1 2-5,6-10 Publication date: November, 2005 Revision A0.92...
Page 258 0 as none of the ports are force untagged Possible value: <vid>: 1 to 4094 <member_range>: 1 to 26 <untag_range>: 0 to 26 Example: 065-7726SPOE(vlan)# set tag-group 2 vlan-2 2-5,6,15-13 0 Publication date: Oct.., 2005 Revision A1...
Page 259 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show config Syntax: show config Description: To display the current vlan mode, Symmetric vlan, SVL and Double tag states. Argument: None. Possible value: None. Example: 065-7726SPOE(vlan)# show config...
Page 260 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual show pvid Syntax: show pvid Description: To display pvid, priority and drop untag result. Argument: None Possible value: None Example: 065-7726SPOE(vlan)# show pvid Port PVID Priority Drop Untag...
Page 261 To enable the virtual stack. Argument: None. Possible value: None. Example: 065-7726SPOE(vs)# enable set gid Syntax: set gid <gid> Description: To set the group id. Argument: <gid>: group ID Possible value: a-z,A-Z,0-9 <gid>: Example: 065-7726SPOE(vs)# set gid group1 Publication date: November, 2005 Revision A0.92...
Page 262 Description: To set role. Argument: <master|slave>: master: act as master, slave : act as slave Possible value: <master|slave>: master or slave Example: 065-7726SPOE(vs)# set role master show Syntax: show Description: To display the configuration of the virtual stack. Argument: None.
Page 263: Chapter 5. Maintenance
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual 5. Maintenance 5-1. Resolving No Link Condition The possible causes for a no link LED status are as follows: The attached device is not powered on The cable may not be the correct type or is faulty...
Page 264: Appendix A Technical Specifications
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Appendix A Technical Specifications Features The switch included 24-Port 10/100Mbps TP and 2-Port Gigabit Dual Media • TP/SFP Supports 24-port 10/100M TP ports with Nway and auto MDIX function.
Page 265 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual PoE-PSE status and activity LED indicator. • Smart feature for PD on/off, class, feeding priority. • Publication date: November, 2005 Revision A0.92...
Page 266 Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Hardware Specifications Standard Compliance: IEEE802.3ab / 802.3z / 802.3u / 802.3x 802.3z and 802.3ab compliant Gigabit Ethernet ports Network Interface of Option transceiver Configuration Mode Connector Port SFP.0LC.202...
Page 267 ™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Diagnostic LED: System LED : Power CPURUN ACT (LEDSET) FDX (LEDSET) SPD (LEDSET) Per Port LED: 10/100M TP Port 1 to 24 : LINK/ACT, FDX, SPD 1000M Fiber/TP Port 25,26...
Page 268: Management Software Specifications
Signamax ™ ™ ™ ™ 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Management Software Specifications Auto-negotiation support on 10/100Base-TX ports, Web browser or console interface can set transmission speed (10/100Mbps) and System Configuration operation mode (Full/Half duplex) on each port, enable/disable any port, set VLAN group, set Trunk Connection.
Page 269: Appendix B Null Modem Cable Specifications
™ ™ ™ ™ Signamax 065-7726SPOE 24-Port 10/100BaseT/TX PoE Managed Switch User Manual Appendix B Null Modem Cable Specifications The DB-9 cable is used for connecting a terminal or terminal emulator to the Managed Switch’s RS-232 port to access the command-line interface.

SignaMax 065-7726SPOE User Manual

Chapter 1. Introduction

Chapter 2. Installation

Chapter 3. Operation of Web-Based Management

Chapter 4. Operation of Cli Management

Chapter 5. Maintenance

Appendix A Technical Specifications

Appendix B Null Modem Cable Specifications

Quick Links

Related Manuals for SignaMax 065-7726SPOE

Summary of Contents for SignaMax 065-7726SPOE

Table of Contents