Fbx Bypass Button - SABINE SWM7000 Operating Manual

fully, and your mixer meters show little movement when signal passes through,
then your amplifier will have to work harder to process the weak signal. You
will improve the performance of your sound system and lower system noise
by reducing the gain on your power amp and increasing your mixer gain. FBX
response time will also be better with proper gain structure.
4. First, turn on your receiver and select a clear channel (no RF Signal bars
showing). Then turn on your wireless transmitter or handheld microphone
and select the same channel, Now turn on the mixer (gain low), then any
other accessories, and finally the power amp. If you are using a graphic EQ,
adjust only for the desired tonal qualities, but do not notch for feedback!
5. With the microphone turned on, raise the Output Level of the receiver slowly
until a strong input signal at the mixer is apparent. The microphone should
now be audible.
6. Now you are ready to set FBX filters. Press and hold SETUP (far left button)
on the wireless receiver, until the word SETUP in the channel LCD flashes
4 times, then stops flashing. This will clear any FBX filters already in place.
NOTE: You should do this each time you move your sound system, change
a sound system component, or relocate your microphone. Your Sabine True
Mobility Wireless System will remember its settings from the last time you
turned the unit off.
7. During Setup mode, do not talk into the microphone or pass audio program
through a transmitter. This may cause the Sabine True Mobility™ system to
set inappropriate filters. The only appropriate use of the setup mode is to
create and filter feedback. SETUP must be exited prior to normal microphone
usage. This happens automatically after setting FBX filters, or you may exit
manually by pressing READY at any time.
8. Identify the primary usage positions, and likely feedback-prone locations, in the
potential movement range of the wireless microphone. Take the microphone
to the first of these locations.
9. Slowly raise the mixer channel gain to the point of feedback — and then slowly beyond, until you hear the chirping tones
of feedback quickly being eliminated by FBX filters setting. Stop raising gain after 2 or 3 feedback tones have chirped and
corresponding FBX filters have set. Rest assured that any feedback that occurs will be at a quiet volume, and very short
in duration.
10. Move the microphone to another area of use and slowly raise gain until FBX eliminates a few more feedback tones (2 or
3). Repeat this step until the word Setup automatically disappears and the word READY appears. This indicates your unit
is ready for operation. The total number of filters available for feedback filtering is 10; in the factory default setting, your unit
will automatically enter READY mode when the eighth filter is set. Alternatively, you may enter READY status with fewer
fixed FBX filters in place, simply by pressing the READY button at any time. NOTE: Be sure that the word READY appears
in the FBX section of your receiver LCD during performance or any normal operation.
Any feedback that occurs after setup will be eliminated by dynamic filters, which remain in reserve to catch surprise feed-
back if it occurs during performance/operation.
In most instances you will experience an additional gain of 6-9 dB before feedback when using the Sabine True MobilityTM
System. Precise results will depend on system and acoustical considerations.
All fixed filters in place will remain set until the Setup button is pushed and held as described in step 6. All dynamic filters
will remain in place until new feedback occurs (when they will move to the new frequency), or until the Setup button is
pushed and held. Your True Mobility receiver will remember its FBX (and all other) settings even if the power is turned off.
See Section 14 for a complete discussion of Sabine FBX Feedback Exterminators®.

7 .2. FBX Bypass Button

The Bypass button bypasses only the FBX Section, and not the additional signal processing (Parametric Filters, Hi/Lo Cut, De-es-
sing and Compression) available in the Targeted Input Processing section of the Sabine True Mobility™ Wireless Receiver.
NOTE: You can easily bypass Compression signal processing by turning the Compressor Ratio knob counterclockwise until
you get to 1:1 ratio, and the De-esser signal processing by turning the De-esser knob clockwise until you get to 0 cut.
FBX Feedback Exterminator
Fig. 7c: READY Button
READY = Lock Fixed on other Sabine
FBX products
Fig. 7d:BYPASS Button
29
Tech Tip
READy & Locked Fixed
Sabine Smart Spectrum Wireless
®
LIT-SWM6-7000-OG-EN-110203.indd