Glass Replacement Procedures; Vermiculite Panel Replacement; Stone - HearthStone Bari 8170 Owner's Manual

Required Glass Kit: Part Number: 040-057-V (Glass with
gasket applied).
G
LASS REPLACEMENT PROCEDURES
1. Follow the instructions included with the replacement glass kit.
2. Remove the door (see door removal procedure on page 18).
3. Remove the screws from the glass retainer (use penetrating oil
if necessary) – lift the retainer off the glass. Set aside for
reinstallation.
4. Remove the inner glass frame from around the glass. Set aside
for reinstallation.
5. Carefully lift the damaged glass out of the door and discard.
6. Remove any remaining glass and old gasket material.
7. Clean the screw holes and place a small amount of anti-seize
compound in each one.
8. Place the gasketed new glass onto the door.
9. Important! Center the glass and ensure that the edges of the
curved glass are parallel with the edges of the opening.
10. Reinstall the inner glass frame (limits pressure on glass from
the retainer).
11. Check glass position again (centered, and parallel), then screw
the glass retainer back on the door using a crisscross pattern.
Tighten the screws no more than 1/8
(The glass will break at this point if not positioned correctly. If
the glass shifts too much to one side, you will see the gasket
from the outside)
12. Apply a light film of anti-seize lubricant on the door's hinge
pins and washer if needed.
13. Install the door.
14. After 5 or 6 fires, check the glass retainer screws, and retighten
if necessary.
Figure 12 Glass Assembly
V P R
ERMICULITE ANEL EPLACEMENT
1.
Remove packing material from spaces along front edges of the
outer left and outer right panels.
HearthStone Quality Home Heating Products, Inc ®
:
th
of a turn after they seat.
:
20
2.
Remove the panel lock plate above the outer right panel.
3.
Slide outer right panel slightly to the right, tilt top into firebox,
and remove the panel.
4.
Slide all other panels to the right, tilt, and remove.
5.
To remove the upper panel, remove the screw securing the air
tube, slide the air tube to the left, and remove it. Drop down
the upper panel.
6.
Install the side panels by placing each one into the right most
position and then slide it to the left. All side panels are
identical.
7.
Replace side panel lock plate.
8. Push side panels together tightly and center them so the spaces
along the front edges are equal, Insert packing to prevent panel
separation.
9. To install the upper panel, insert the panel rear edge first into
the space below the baffle plate – hold in place and insert the
air tube. Seat air tube to the right and reinstall screw.
Figure 13 - Panel Detail
S
TONE
The stone panels on this stove are large and heavy (150
pounds total). Use a second person to assist in mounting the
panels to avoid injury, or damaging the panels. Despite the
mass of each piece of soapstone, they will break if dropped.
Occasional cleaning is all that is necessary to maintain the
natural beauty of your stove's soapstone finish. Clean the
soapstone with water, any non-abrasive cleaner and a soft
cloth. Wipe dust from the stone with a clean cloth. Do not
use chemical agents to wash the stone; do not use waxes or
any polishing agents on the stone.
Take care not to scratch or chip the soapstone. Do not set
items that can scratch or chip the stone on top of your stove.
You can use 240 grit sandpaper to easily repair, or blend in
minor scratches
Often, with use and over time, subtle earth tones of brown,
red, and yellow may appear in the soapstone. This is a
natural reaction in the soapstone. Surface or hairline fractures
may also appear in the stone after a stove is used. Such
changes are normal and do not affect the operation or the
integrity of the stove and do not require replacement. If you
observe a completely broken stone, contact your dealer for
service.
Bari Model 8170