Page 1
Hammer Drill Kit Instruction Manual 3 Year Replacement Warranty CDR-018 WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
Drill. We aim to provide quality tools at an affordable price. We hope you will enjoy using this tool for many years. Your Cordless Hammer Drill CDR-018 has been designed to drill masonry, metal, plastic and for screw driving. It is intended for DIY use only.
GeneRal poWeR tool Safety WaRninGS WaRninG! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in all of the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Page 6
GeneRal poWeR tool Safety WaRninGS f) dress properly. do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g) if devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
BatteRy and cHaRGeR Safety WaRninGS THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR YOUR BATTERY CHARGER. Before using the charger read all instructions and cautionary markings on the charger, battery pack and the product using the battery pack. danger! If the battery pack case is cracked or damaged, do not insert it into charger.
additional Safety WaRninG foR HammeR dRillS Do not use the drill in wet or damp conditions. Always keep the work area free of tripping hazards. When using the drill always ensure you are wearing protective safety equipment including safety glasses/goggles, ear muffs, dust mask and other protective clothing including gloves and apron.
cHaRGinG youR BatteRy The drill’s battery (8) has been shipped in a low charge condition, and requires charging prior to use. Connect the charging jack (10) to the charging cradle (11) (Fig. 1). Plug the charging adaptor (9) into a mains power outlet.
cHaRGinG youR BatteRy (cont.) important charging notes The charging adaptor (9) and battery (8) may become warm to touch while charging. This is a normal condition, and does not indicate a problem. Use the charger at normal room temperature whenever possible. To prevent overheating, do not cover the charger and do not charge the battery pack in direct sunlight or near heat sources.
inStallinG oR RemoVinG tHe BatteRy (cont.) Getting the Best performance from the Battery The length of service from each charging cycle will depend on the type of work you are doing. To obtain the longest possible battery life, we suggest the following: Store and charge your battery (8) in a cool area.
Page 12
HammeR dRil opeRation (cont.) changing the direction of Rotation The direction of rotation can be changed with the forward/reverse lever (4). This is located above the variable speed trigger (6) (Fig. 6). To select the forward drilling position, push the forward/reverse lever (4) hard left.
Page 13
HammeR dRill opeRation (cont.) installing drill or driver Bits WaRninG! Remove battery from the drill before attempting to change accessory. failure to do so may cause serious personal injury. WaRninG! Do not hold the chuck body with one hand and use power of the drill to tighten or loosen the chuck jaws.
Page 14
HammeR dRill opeRation (cont.) Wood drilling Mark the place where you want to drill with a punch or a nail. To avoid splintering on breakthrough, either clamp a piece of scrap wood to the back of your workpiece or continue the hole from the back of the wood when the drill bit first breaks through.
If the housing of the drill requires cleaning, do not use solvents but cloth only. Blow out the ventilation slots with compressed air periodically . note: Ozito Industries will not be responsible for any damage or injuries caused by repair of the biscuit joiner by an unauthorised person or by mishandling.
If the tool shows signs of damage or defects caused by or resulting from abuse, accidents or alterations. • Failure to perform maintenance as set out within the instruction manual. • If the tool is disassembled or tampered with in any way. ozito Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175...
Need help?
Do you have a question about the CDR-018 and is the answer not in the manual?
Questions and answers