Related Manuals for Lionel AMC/ARC Log Loader
Summary of Contents for Lionel AMC/ARC Log Loader
- Page 1 72-4115-250 10/04 Car and track not included. Lionel AMC/ARC Log Loader Owner’s Manual...
-
Page 2: Table Of Contents
Removing a loop Resetting the Log Loader in the TrainMaster Command Control environment CAB-1 Remote Controller commands Limited Warranty/Lionel Service The following Lionel marks may be used throughout this instruction manual and are protected under law. All rights reserved. Lionel ®... -
Page 3: Placing The Log Loader On Your Layout
Placing the Log Loader on your layout he Log Loader is designed for use with remote-control log dump cars (available separately). Position a log dump car over the magnetic disk on a remote-control track section (available separately, 6-65530 for O gauge, 6-65149 or 6-12746 for O-27 gauge, and 6-12020 for FasTrack layouts), and activate the track section to dump the logs into the log loader’s bin. -
Page 4: Connecting The Power Supply
Connecting the power supply our Log Loader was designed to operate at 16-18 volts (AC). The power supply terminals are located along the side of the controller. Refer to Figure 2. Please note that the ends of the wires must be stripped back 1/8” to 1/4”. Only an adult should perform this task. -
Page 5: Operating The Log Loader With The Controller
Operating the Log Loader with the controller he Log Loader has three different functions that can be operated using a controller lever. The controller levers are illustrated in Figure 3. The LED will illuminate each time you operate a lever. •... -
Page 6: Connecting The Log Loader For Operation In The Trainmaster Command Control Environment
Connecting the Log Loader for operation in the TrainMaster Command Control environment o operate the Log Loader using your CAB-1 Remote Controller (available separately, 6-12868), you must connect the Crane to the Command Base (available separately, 6-12911). The Command Base will transmit your CAB-1 Remote Control commands to this accessory. If you have no other TMCC Controllers connected, you will need to wire the Log Loader to the Command Base using a Command Base Cable (available separately, 6-14191 or 6-14195). -
Page 7: Assigning An Id Number To Your Log Loader
Assigning an ID number to your Log Loader repare your Log Loader for operation in the TrainMaster Command Control environment by assigning a unique engine (ENG) ID number to it. The Log Loader will only respond to commands that are intended for this ID number. 1. -
Page 8: Operating Your Log Loader In The Trainmaster Command Control Environment
Operating your Log Loader in the TrainMaster Command Control environment fter you have connected the Log Loader to the Command Base and assigned it a unique ID number, you are ready to operate the accessory. Please note that the Log Loader will respond only while you are operating the controls. -
Page 9: Making A Simple Recording With The Log Loader
Making a simple recording with the Log Loader ollow these steps to create a simple recording with the Log Loader. As you use your CAB-1 Remote Controller to operate the Log Loader, the accessory will memorize each command. After you press AUX1, 9, you have 45 seconds to create a recording. A CAB-1 Remote Controller and Command Base are required to make a recording. -
Page 10: Playing The Recording
Playing the recording Follow these steps to play your recording. Always keep the starting point (the initial position of the Log Loader) and the input Hint! voltages the same. We recommend that you start with the Log Loader stopped. Before you play the recording, be sure to position the accessory where it was when you started to record for more consistent results. -
Page 11: Resetting The Log Loader In The Trainmaster Command Control Environment
Resetting the Log Loader in the TrainMaster Command Control environment o reset your Log Loader in the TrainMaster Command Control environment, simply remove the run/program jumper, press H on the CAB-1 Remote Controller, and then replace the jumper. Alternately, you may follow the conventional reset procedure as discussed on page 6. CAB-1 Remote Controller commands Operates the stakes. -
Page 12: Limited Warranty/Lionel Service
Lionel L.L.C. or an authorized Lionel L.L.C. Service Center, together with proof of original purchase will, at the option of Lionel L.L.C., be repaired or replaced, without charge for parts or labor. In the event the defective product cannot be repaired, and a replacement is not available, a refund of the original purchase price will be granted.