Brother MFC-8460N User Manual page 9

Insert paper in the empty tray. Note · The setting in the printer driver will take priority over the setting made on the control panel. · If the control panel is set
to Tray#1 Only, Tray#2 Only, MP Only or MP]T1]T2 and you choose `Auto Select' in the printer driver, the tray use will be MP]T1]T2.
If the control panel is set to T1]T2]MP and you choose `Auto Select' in the printer driver, the tray use will remain T1]T2]MP. a Press Menu, 1, 7, 2. 17.Tray
Use 2.Fax a Tray#1 Only b MP Only Select ab & OK b Press a or b to select Tray#1 Only, Tray#2 Only, MP Only, MP]T1]T2 1 or T1]T2 1]MP.
Press OK. 1 Tray#2 Only and T2 appear only if the optional tray is installed. 19 Chapter 3 Volume Settings Ring volume You can select a ring volume level
from a range of settings, from High to Off. While in Fax mode press or to adjust the volume level. The LCD shows the current setting, and each key press will
change the volume to the next. The machine will keep the new setting until you change it. 3 Speaker volume You can select a range of speaker volume levels,
from High to Off. You can change the volume through the menu, by following the instructions below: 3 3 a Press Menu, 1, 4, 3. 14.Volume 3.
Speaker a Med b High Select ab & OK You can also change the volume through the menu, by following the instructions below: b c a Press Menu, 1, 4, 1.
14.Volume 1.Ring a Med b High Select ab & OK Press a or b to select Off, Low, Med or High. Press OK. Press Stop/Exit. b c Press a or b to select Off, Low,
Med or High. Press OK. Press Stop/Exit. Beeper volume When the beeper is on, the machine will beep when you press a key, make a mistake, or after you
You can select a range of volume levels, from High to Off. 3 a Press Menu, 1, 4, 2. 14.Volume 2.Beeper a Med b High Select ab & OK b c Press a or b to
Press OK. Press Stop/Exit. 20 General setup Setting daylight savings time Ecology features 3 3 Toner save You can save toner using this feature. When you
3 You can set the machine to change for Daylight Savings Time. If you select On, it will reset the time forward one hour and it you select Off, it will reset the
time backward one hour. a a Press Menu, 1, 6, 1. 16.Ecology 1.Toner Save a On b Off Select ab & OK 3 Press Menu 1, 5. 15.Daylight Save On Off Select ab
Press a or b to choose On (or Off). Press OK. Press Stop/Exit. 21 Chapter 3 Sleep time Setting the sleep time reduces power consumption by turning off the
fuser while the machine is idle. You can choose how long the machine must be idle (from 00 to 99 minutes) before it goes into sleep mode. When the machine
receives a fax, computer data or makes a copy, the timer will reset. The default setting is 05 minutes. While the machine is in sleep mode the LCD will display
Sleep. When printing or copying in sleep mode, there will be a short delay while the fuser warms up. 3 Turning off the scanner lamp The scanner lamp stays
on for 16 hours before automatically switching off to preserve the life of the lamp and reduce power consumption.
To turn the scanner lamp off manually press the d and c keys simultaneously. The scanner lamp will remain turned off until the next time you use the scanning
feature. 3 Note Turning the lamp off regularly will reduce the lamp's life. a Press Menu 1, 6, 2. 16.
Ecology 2.Sleep Time Sleep Time:05Min Enter & OK Key LCD Contrast You can change the contrast to make the LCD look lighter or darker. 3 b c a Press
Menu, 1, 8. 18.LCD Contrast -nnonn+ Select d c & OK Enter the length of time the machine is idle before entering sleep mode (00 to 99).
Press OK. Press Stop/Exit. To turn off sleep mode, press Secure and Job Cancel at the same time in b. Press a or b to select Off or On.
send or receive a fax.
select Off, Low, Med or High.
set toner save to On, print appears lighter. The default setting is Off.
& OK a b b c b c Press a or b to select On, or Off. Press OK. Press Stop/Exit.
You're reading an excerpt. Click here to read official BROTHER
MFC-8460N user guide
http://somemanuals.com/dref/310783