Brother MFC-8460N User Manual page 48

a b Press Stop/Exit. Make sure that you have installed MFL-Pro Suite on your PC, and then turn on PC Fax Receiving on the PC. (For details about PC Fax
Receive, see Using Brother PC-FAX software (For Windows®) in the Software User's Guide on the CD-ROM.) Make sure that you have set PC Fax Receive
on the machine. (See PC fax receive on page 67.) During setup the LCD will ask if you want to send the faxes to your PC. Do one of the following: To send all
c d Note You can send the Fax Journal report to another fax machine by pressing Menu, 9, 0, 2 in a. Note If there is an error message on the machine's LCD
after the faxes have been sent, disconnect the machine from the power source for several minutes, and then reconnect it. C Sending faxes to another fax
machine If you have not set up your Station ID, you cannot enter fax transfer mode. a b c Follow a and b in Checking if the machine has faxes in its memory.
Press Start. 120 Troubleshooting and routine maintenance Document jams If the document is jammed, follow the steps below. C c Pull the jammed document
out to the right. Document is jammed in the top of the ADF unit The document may get jammed if it is not inserted or fed properly, or if it is too long. Follow
C a b c Take out any paper from the ADF that is not jammed. Open the ADF cover. Pull the jammed document out to the left. d e Close the document cover.
Press Stop/Exit. Document is jammed at the output tray C a b Take out any paper from the ADF that is not jammed. Pull the jammed document out to the
right. d e Close the ADF cover. Press Stop/Exit. Document is jammed inside the ADF unit C a b Take out any paper from the ADF that is not jammed.
Lift the document cover. c Press Stop/Exit. 121 Document is jammed in the duplex slot (MFC-8860DN only) Paper jams C C a b Take out any paper from the
ADF that is not jammed. Pull the jammed document out to the right. To clear paper jams, please follow the steps in this section. HOT SURFACE After you
have just used the machine, some internal parts of the machine will be extremely hot. When you open the front or back cover of the machine, DO NOT touch
the shaded parts shown in the illustration. c Press Stop/Exit. Paper is jammed inside the machine C a b Pull the paper tray completely out of the machine. Use
122 Troubleshooting and routine maintenance c Press the cover release lever to open the front cover. CAUTION To prevent damage to the machine from
static electricity, DO NOT touch the electrodes shown in the illustration. d Slowly take out the drum unit and toner cartridge assembly. The jammed paper
may be pulled out with the toner cartridge and drum unit assembly, or this may release the paper so you can pull it out of the paper tray opening. e Put the
f g Close the front cover. Put the paper tray firmly back in the machine. 123 Paper is jammed at the back of the machine d C a Pull the tabs at the left and
right hand sides toward you to open the fuser cover (1). 1 Press the cover release lever to open the front cover. b Take out the drum unit and toner cartridge
e Using both hands, gently pull the jammed paper out of the fuser unit. c Open the back cover. f Close the back cover. 124 Troubleshooting and routine
maintenance g Put the drum unit and toner cartridge assembly back in the machine. c Put the duplex tray back in the machine. h Close the front cover. Paper
is jammed inside the drum unit and toner cartridge assembly C Paper is jammed in the duplex tray (MFC-8860DN only) a C Press the cover release lever to
faxes to your PC, press 1. To exit and leave the faxes in the memory, press 2.
Enter the fax number to which faxes will be sent.
the steps below to clear a document jam.
both hands to slowly pull out the jammed paper.
drum unit and toner cartridge assembly back in the machine.
open the front cover.
You're reading an excerpt. Click here to read official BROTHER
MFC-8460N user guide
http://somemanuals.com/dref/310783
assembly.