Brother MFC-8460N User Manual page 7

) Paper Tray (Tray #2) A4, Letter, Executive, A5, B5 and B6 Plain paper, Recycled paper, Bond paper, Envelope and Labels Transparency Plain paper,
Recycled paper and Bond paper No. of sheets up to 250 [80 g/m 2 (20 lb)] up to 10 up to 50 [80 g/m2 (20 lb)] up to 10 up to 250 [80 g/m2] 2 2 13 Chapter 2
Loading paper, and other media When printing on plain paper 60 to 105 gsm (16 to 28 lb) or laser transparencies use the paper tray. For printing on other
types of media use the MP tray (Multi purpose tray). d 2 Fan the stack of paper well to avoid paper feeding problems. Loading paper e 2 a b Unfold the
Pull the paper tray completely out of the machine. Insert the paper into the paper tray with the top edge of the paper first, and the print side down. Make sure
that the paper is flat in the tray and below the maximum paper mark (1). 1 c While pressing the blue paper-guide release lever (1), slide the paper guides to fit
the paper size. Make sure that the guides are firmly in the slots. 1 f Push the paper tray firmly back into the machine. 14 Loading documents and paper
Loading envelopes and other media Use the MP tray when printing envelopes, labels, and thick paper. Loading Envelopes 2 2 Before loading, press the
corners and sides of the envelopes to make them as flat as possible. a 2 Open the MP tray and lower it gently. CAUTION Do not use any of the following types
2 Embossed envelopes (those with a raised surface). b Pull out the MP tray support. 3 Envelopes with clasps or staples. 4 Envelopes that are pre-printed on
the inside. Rounded flap Double flap Triangular flap 2 Glue 2 2 2 c Insert the media into the MP tray with the top edge first and the printing side face up. 15
Chapter 2 Printable Area Printable Area for copies The printable area of your machine begins at approximately 3 mm (0.12 in.) from the top and bottom and
) from both sides of the paper. 2 1 2 2 Printable Area when printing from a computer When using the default driver the printable area is smaller than the
) 6.01 mm (0.24 in.) Landscape 2 1 2 Note This printable area shown above is for a single copy or a 1 in 1 copy using A4 size paper. The printable area
) Note The printable area shown above is for A4 size paper. The printable area changes with the paper size. 16 3 General setup Paper settings Paper Type Set
up the machine for the type of paper you are using. This will give you the best print quality. 3 Mode timer The machine has three mode keys on the control
panel: Fax, Scan, and Copy. You can set how much time the machine takes after the last Copy or Scan operation to return to Fax mode. If you select Off, the
machine will stay in the mode you used last. This setting also sets the time the machine will change from individual user to public user when using Secure
Function Lock. See Switching Users on page 27. 3 3 3 3 a Choose one of the options below: To set the paper type for the MP Tray press Menu, 1, 2, 1.
To set the paper type for Tray#1 press Menu, 1, 2, 2. To set the paper type for Tray#2 press Menu, 1, 2, 3 if you installed the optional tray. 12.Paper Type
Mode Timer a 0 Sec 30 Secs b 1 Min Select ab & OK b c b c Press a or b to select Thin, Plain, Thick, Thicker, Transparency or Recycled Paper. Press OK.
) Length: 116.0 to 406.4 mm (4.57 to 16.0 in.
of envelope, as they will cause paper feed problems: 1 Envelopes with a baggy construction.
paper size, as shown below. Portrait 2 1 2 2 2 1 1 1 2 3 mm (0.12 in.) 2.
05 mm (0.08 in.) 1 2 4.23 mm (0.16 in.
changes with the paper size. 1 1 2 4.23 mm (0.16 in.) 5 mm (0.19 in.
1.MP Tray a Plain b Thick Select ab & OK a Press Menu, 1, 1 11.
Press Stop/Exit. Press a or b to select 0 Sec, 30 Secs, 1 Min, 2 Mins, 5 Mins or Off. Press OK.
Press Stop/Exit. Note · Transparency is not available for the optional Tray #2.
You're reading an excerpt. Click here to read official BROTHER
MFC-8460N user guide
http://somemanuals.com/dref/310783
9 to 215.9 mm (2.75 to 8.5 in.
output paper tray support flap.
2.05 mm (0.08 in.