Download Print this page

Advertisement

DESKPOWER 5000 Series User's Manual
Fujitsu endeavours to ensure that the information in this document is correct, but accepts no liability
for any error or omission in the same. Any procedures described in this document for operating
Fujitsu products should be read and understood by the operator before such products are used.
To ensure that Fujitsu products function without risk to safety and health, such procedures should
be strictly observed by the operator. The development of Fujitsu products and services is
continuous and published information may not be up to date. Any particular issue of a product
may contain facilities not described herein. It is important to check the current position with Fujitsu.
Specifications and statements as to performance in this document are Fujitsu estimates intended
for general guidance. They may require adjustment in particular circumstances and should
therefore not be taken as formal offers or commitments.
DESKPOWER is a trademark of Fujitsu Limited. The following are registered trademarks of
Miscrosoft Corporation: MS, MS-DOS, Windows
®
NT, Windows
®
for Workgroups, Windows® 95,
Windows
®
98, Windows
®
2000. Intel 810E, Celeron,Pentium II and III are the registered trade
mark of Intel Corporation. Phoenix and the Phoenix logo are registered trademarks of Phoenix
®
Technologies, Ltd. Intel
Pentium
and MMX
technology are trademarks of Intel Corporation.
ATI Graphic Chip: RAGE PRO TURBO and RAGE XL are the registered trademarks of ATI
Technologies, Inc. Award is the registered trademark of Award Software International Inc.
©
All Rights Reserved. Copyright
Fujitsu Limited, 2000
The use of screens is permitted by Microsoft Corporation in the United States.
All other products are trademarks or registered trademarks of their respective companies.
© Copyright 2000 Fujitsu Limited. All rights reserved. No part of this publication may be copied,
reproduced, or translated without the prior written consent of Fujitsu Limited. No part of this
publication may be stored or transmitted in any electronic form without the written consent of Fujitsu
Limited.
Fujitsu PC (Asia) Pte Ltd
200 Pandan Loop
#05-03 Pantech 21
The Computer Centre
Singapore 128388
Tel
: 65-776 0688
Fax : 65-776 0788

Advertisement

Troubleshooting

   Summary of Contents for Fujitsu 5000 Series

  • Page 1

    DESKPOWER 5000 Series User’s Manual Fujitsu endeavours to ensure that the information in this document is correct, but accepts no liability for any error or omission in the same. Any procedures described in this document for operating Fujitsu products should be read and understood by the operator before such products are used.

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions carefully. Save these instructions for future reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

  • Page 3

    This unit may malfunction if the power source is interrupted suddenly, for example, due to lightning. Fujitsu recommends the use of an AC non-interruptible power supply unit. (Based on guidelines for the prevention of sudden voltage interruptions by Japan Electronic Industry Development Association (JEIDA).

  • Page 4: Conventions Used In This Manual

    Conventions used in this manual Warning icons Various icons and icon/word combinations are used in this manual to encourage users to use the equipment so as to minimize personal risk and prevent property damage. The icons are explained as follows. The user should be familiar with the icons before responding to the corresponding instructions.

  • Page 5

    Conventions used in the text of the manual The symbols used in the text of the manual have meanings as explained below: Point Point indicates information necessary to run hardware or software. Help Help indicates information explaining how to terminate an incorrect operation or troubleshoot.

  • Page 6: Rear Of The Pc Main Unit

    Warning and caution labels The PC bears warning and caution labels as shown below. The warning and caution labels must not be removed or damaged. Rear of the PC main unit To prevent electric shock, WARNING switch off the PC and connected peripherals and Electric shock unplug power cords from...

  • Page 7: Chapter 1 Installation And Connection

    Manual configuration Chapter 1 Installation and Connection This chapter outlines precautions that should be noted when installing the PC and explains how to connect various cables. Consult this chapter before assembling the PC. Chapter 2 Basic Operations This chapter explains basic operations required to use the PC, such as how to switch the power on and off and how to proceed with storage media.

  • Page 8: Table Of Contents

    Content Chapter 1 Installation and Connection ..........1 1 Installation ................2 Installation location ..................2 Example of installing the PC ..............2 Preventing electromagnetic interference with a TV or radio ....... 3 2 Connection ................4 Attaching CRT display, keyboard, mouse, and LAN cables ....... 5 Connecting the power cord ................

  • Page 9

    Chapter 3 Installing Internal Options ..........19 1 Introduction ................. 20 Handling precautions ................20 Installing positions of internal options ............21 Removing the upper cover ............... 22 Removing the front panel ................. 22 2 Installing Memory Modules ..........22 Memory ....................

  • Page 10

    Appendix ..................53 1 Name and Function of Each Component ......54 Front of the PC main unit ................. 54 Rear of the PC main unit ................. 57 Inside the PC main unit ................58 Motherboard/riser board ................59 2 Standard Specifications ............. 60 PC main unit specifications ..............

  • Page 11: Chapter 1 Installation And Connection

    Chapter 1 Installation and Connection This chapter outlines precautions that should be noted when installing the PC and explains how to connect various cables.

  • Page 12: Installation

    1 Installation This section provides notes on installing and using the PC. Installation location Do not install the PC in the following areas: - Area exposed to moisture, dust, or smoke - Area poorly ventilated - Area having open flames - Area that may expose the PC to water - Area exposed to direct sunlight or high temperatures.

  • Page 13: Preventing Electromagnetic Interference With A Tv Or Radio

    Preventing electromagnetic interference with a TV or radio Your PC complies with the VCCI Standard restricting electromagnetic interference with a TV or radio. However, the computer may interfere with a TV or radio depending on the installation location. To prevent the PC from interfering with TV or radio reception, note the following: Precautions to be taken by the PC user - Do not use the PC with the cover removed.

  • Page 14: Connection

    LAN cables, and power cords. To prevent electric shock, fire, and/or Electric shock malfunction, ensure that the display, keyboard, and mouse are all Fujitsu brand products. CAUTION Ensure that cables are connected correctly. Failure Connect the LAN cable.

  • Page 15: Attaching Crt Display, Keyboard, Mouse, And Lan Cables

    Attaching CRT display, keyboard, mouse, and LAN cables Point This section explains how to connect the CRT display so as to supply power from the PC main unit. In this case, the power cord included with the CRT display is not used. Connect the power cord to the CRT display.

  • Page 16: Connecting The Power Cord

    Connecting the power cord After connecting the display and other peripherals to the PC main unit, note the following when connecting the power cord of the PC main unit. - Do not plug or unplug the power cord with wet hands. - Do not damage or remodel the power cord.

  • Page 17: Chapter 2 Basic Operations

    Chapter 2 Basic Operations This chapter explains basic operation methods of the PC such as how to turn the power on and off and handle storage media.

  • Page 18: Switching On

    1 Switching on This section explains how to switch on the PC. CAUTION Prohibited action To prevent malfunction after turning on the PC, do not move equipment or subject equipment to shock and/or vibration. Press the power switch of the CRT display. There is no display.

  • Page 19

    Point - Before switching on the PC, make sure that display is connected. If the PC is switched on before the display is connected, the display adapter may not be recognized, and the screen may not be displayed normally. In this case, connect the display, terminate the OS, switch off the PC, and then switch on the PC again.

  • Page 20: Switching Off

    2 Switching off This section explains how to turn off the PC. Point - Before turning off the power, terminate all jobs and save all necessary data. - Before turning off the power, confirm that the access indicator lamps ( see Appendix 1, "Name and Function of Each Component") of the floppy and hard disk drives are off.

  • Page 21: Turning Off The Power Via Windows Nt

    BIOS Setup A guide to your Deskpower 5000 BIOS is available online. Please visit our technical support section at www.fujitsu-pc-asia.com. Once there, click on the desktop series from the pull down menu and select the appropriate desktop model. Turning off the power via Windows NT Click [Start].

  • Page 22: Reset

    3 Reset The PC is reset after the operating system in configured or if software fails to run normally. This section explains how to reset the PC. Point Resetting the PC results in memory data being lost. Before resetting, save all necessary data. Resetting the PC via Windows 98 This section explains how to reset the PC via Windows 98.

  • Page 23: Resetting The Pc Via Windows 2000

    Resetting the PC via Windows 2000 This section explains how to reset the PC via Windows 2000. Click [Start] and "Shut Down". The "Shut Down Windows" dialog box appears. Select [Restart] and click [OK]. The PC is reset. Point The following procedure can also be used to reset the PC: 1 Press [Ctrl] + [Alt] + [Delete].

  • Page 24: Handling Precautions

    4 Floppy Disk A floppy disk is a storage medium used to save programs and other information. This section explains how to mount and dismount floppy disks. Point Use a floppy disk formatted for DOS. If a disk other than DOS is used, the operation may not execute correctly.

  • Page 25

    Floppy disk access Dismounting a floppy disk indicator lamp Confirm that the floppy disk access indicator lamp is off. Point To prevent data from being destroyed, do not dismount a floppy disk from the drive when the floppy disk access indicator lamp is on. Press the floppy disk eject button.

  • Page 26: Handling Precautions

    5 CD-ROM Your PC incorporates a CD-ROM drive(depending on the model). This section explains how to handle, mount, and dismount CD-ROM disks. Handling precautions To prevent malfunctions, note the following precautions regarding CD-ROM disks: - Do not write on the label side (printed side) using a ball-point pen or pencil and do not affix extra labels.

  • Page 27: Mounting And Dismounting A Cd-rom Disk

    Mounting and dismounting a CD-ROM disk Mounting a CD-ROM Press the EJECT button. The CD-ROM tray is ejected. BUSY lamp EJECT button With the label side of the CD-ROM disk Label side facing up, place the CD-ROM disk in the center of the tray.

  • Page 28: Hard Disk

    6 Hard Disk Your PC incorporates a built-in hard disk. This section outlines precautions to take when handling a hard disk. What is a hard disk? A hard disk is used to save software and other data and consists of a magnetic disk packed in a box as shown on the right.

  • Page 29: Chapter 3 Installing Internal Options

    Chapter 3 Installing Internal Options This chapter explains how to install internal options such as hard disk and expansion cards. Consult this chapter as required.

  • Page 30: Introduction

    - Secure the board by the metal bracket portions or an edge of the PC board such that the surface of the PC board and the soldered sections are not handled. - Installation and disassembly of options other than Fujitsu brand products void the warranty.

  • Page 31: Installing Positions Of Internal Options

    Installing positions of internal options Built-in hard disk (standard) Replacing a hard disk with larger capacity increases the storage capacity of the PC. 3.5-inch file bay Install 3.5-inch file bay options. Expansion card slot The usual devices installed are as follows. Expansion cards extend the range of - Hard disk (IDE standard, SCSI standard) the features of the PC.

  • Page 32: Removing The Upper Cover

    Removing the upper cover When installing internal options, remove the upper cover so as to reveal the inside of the main unit. Remove three screws at the rear of the PC main unit. Remove the upper cover. Slide the upper cover to the rear of the PC main unit (in the direction of arrow in the figure) Lift and remove the cover (in the direction of...

  • Page 33: Installing Memory Modules

    To prevent electric shock, before installing and removing memory modules, turn off the PC and connected units and unplug power cords from respective outlets. Electric shock To prevent electric shock, fire, and/or malfunction, install only Fujitsu brand memory modules in the PC. CAUTION Injury To prevent personal injury and/or malfunction, when installing and removing memory modules, only remove screws from specified locations.

  • Page 34: Memory

    To ensure a total of 512 megabytes of memory, replace the memory module in DIMM1 with a 256-megabyte memory module. Point Install a Fujitsu genuine memory module to ensure PC operation. Installing an additional memory Remove the upper cover. Push down the hooks at both ends of the slot.

  • Page 35: Removing The Memory

    Removing the memory Remove the upper cover. Open the hooks out at both ends of the slot and remove the memory module. Point Note that opening the hooks out forcefully causes the memory card to pop out of the slot and may cause a malfunction.

  • Page 36: Installing Expansion Cards

    To prevent electric shock, before installing and removing expansion cards, Electric shock turn off the PC and connected units and unplug power cords from respective outlets. To prevent electric shock, fire, and/or malfunction, install only Fujitsu brand expansion cards in the PC. CAUTION Injury To prevent injury, when installing and removing expansion cards, remove screws only from specified locations.

  • Page 37: Expansion Cards For Pci Bus (plug & Play Compatible Cards)

    To prevent injury and/or malfunction, do not touch PC board components not Injury specified. To prevent injury and/or device failure, do not touch the metal bracket on the motherboard at the rear of the PC main unit. To install expansion cards, "resources" must be set. The floppy disk drive or hard disk drive inside the PC uses predetermined paths specific to those devices when transferring data with the CPU and memory.

  • Page 38: Expansion Card Installation Procedure For A Pc Using Windows 98

    Expansion card installation procedure for a PC using Windows 98 Start Before installing the expansion card, check resources that can be set for the See the manual included with the expansion card to be installed. expansion card. Are the resources required by the expansion card unused resources of the PC? Release the resources by disabling the expansion card or...

  • Page 39: Expansion Card Installation Procedure For A Pc Using Windows Nt

    Expansion card installation procedure for a PC using Windows NT Start Before installing the expansion card, check the resources that can be set for See the manual included with the the expansion card to be installed. expansion card. Are the resources required by the expansion card unused resources of the PC? Release the resources by disabling the expansion card or...

  • Page 40: Starting And Terminating The Icu (for A Pc Using Windows Nt)

    Starting and terminating the ICU (For a PC using Windows NT) This section explains how to start and terminate the ICU using Windows NT. If the PC is turned on, turn it off. Confirm that the "boot disk" is in write-enable status, insert in the floppy disk drive, then turn on the PC.

  • Page 41: Installing An Expansion Card

    Installing an expansion card To install a large expansion card, remove the motherboard as shown in step 3. To install a small expansion card, steps 2, 3, 7, and 8 are not required. Remove the upper cover. Remove the retaining metal bracket at the side (for installing a large expansion card).

  • Page 42

    Secure the expansion card with the screw. Secure the expansion card with the screw removed in step 4. Install the motherboard (when a large expansion card has been installed). Firmly insert the motherboard and hold it down with the lever. Label Lever Install the retaining metal bracket at the side...

  • Page 43: Installing Expansion Bay Options

    4 Installing Expansion Bay Options This section explains how to install expansion bay options such as internal hard disk, magneto-optic disk drive, CD-ROM drive, and floppy disk drive. The power can be supplied from the PC main unit to the expansion bay options, differing from external-type devices; therefore, an outlet is not required. This is also useful in saving space.

  • Page 44

    Electric shock To prevent an electric shock, fire, and/or malfunction, install only Fujitsu genuine internal options in the PC expansion bay. CAUTION Injury...

  • Page 45: Replacing A Internal Hard Disk Equipped As Standard

    Replacing a internal hard disk equipped as standard This section explains how to replace a standard-equipped internal hard disk with a hard disk of larger capacity. Set up the jumper switch. See the manual accompanying the internal hard disk and make sure that the jumper switch has been set to master, or cable select.

  • Page 46

    Menu," "BIOS Setup"). Point BIOS Setup A guide to your Deskpower 5000 BIOS is available online. Please visit our technical support section at www.fujitsu-pc-asia.com. Once there, click on the desktop series from the pull down menu and select the appropriate desktop model.

  • Page 47: Installing Internal Options To 3.5-inch Expansion Bays

    Installing internal options to 3.5-inch expansion bays This section explains how to install 3.5-inch expansion bay options such as a 3.5-inch internal hard disk, magneto-optic disk drive, and 3.5-inch floppy disk drive. A magneto-optic disk drive is used below in an installation example. Set the internal option.

  • Page 48

    Remove the retaining metal bracket from the PC main unit. Slide the retaining metal bracket toward the rear side of the PC main unit, and then lift and remove the retaining metal bracket. Install a internal option in the retaining metal bracket.

  • Page 49

    Connect the flat cable. Connect the flat cable that is appropriate for the internal option to be installed. - To install two IDE-standard internal options to the IDE secondary cable (if one of the options is a hard disk), install the hard disk at the master side.

  • Page 50

    To remove the internal option, reverse the above procedure. Point BIOS Setup A guide to your Deskpower 5000 BIOS is available online. Please visit our technical support section at www.fujitsu-pc-asia.com. Once there, click on the desktop series from the pull down menu and select the appropriate desktop model.

  • Page 51: Installing Internal Options To 5-inch Expansion Bays

    Installing internal options to 5-inch expansion bays This section explains how to install 5-inch expansion bay options such as CD-ROM drive and 5- inch floppy disk drive. A CD-ROM drive is used below in an example of installation. Up to two 5- inch expansion bay options can be installed in your PC.

  • Page 52

    Secure the internal option with two screws. Connect the flat cable. Connect the flat cable appropriate for the internal option to be installed. - To install an IDE-standard internal option, connect the flat cable to the master or slave connector according to the setting of the internal option.

  • Page 53

    - To install a floppy disk drive: Connect the flat cable to the expansion card of the internal floppy disk drive in the expansion slot. Connect the power cord. Connect the unused power cord to the connector of the installed internal option. Install the blank panel (for an option that does not require a medium be mounted/ dismounted)

  • Page 54

    "Main Menu," "BIOS Setup"). Point BIOS Setup A guide to your Deskpower 5000 BIOS is available online. Please visit our technical support section at www.fujitsu-pc-asia.com. Once there, click on the desktop series from the pull down menu and select the appropriate desktop model.

  • Page 55: Chapter 4 Troubleshooting

    Chapter 4 Troubleshooting This chapter explains the procedure to follow if the computer does not operate as expected.

  • Page 56: Error Messages

    RAM module error is expected. Replace with another extended RAM module and determine whether the error recurs. If the error recurs, contact a dealer or the Fujitsu service center. Confirm that the extended RAM module is mounted An error occurred at address properly and is a Fujitsu product.

  • Page 57

    Error Message Description and necessary action An invalid hard disk drive was set. Confirm ‘Primary master’ or ‘Secondary master’ on the BIOS setup main menu. If the message is still displayed, contact a dealer or the your local distributor. Turn the power off, then on again. If the message is still displayed, contact a dealer or the your local distributor.

  • Page 58

    Error Message Description and necessary action Invalid system disk Replace the disk, and then press any key This message is displayed when the PC is switched on while a floppy disk other then a system disk is set in the floppy disk drive. Remove the floppy disk and press any key.

  • Page 59: Correcting Errors

    If optional extension cards are mounted, confirm that the cards are mounted and set up correctly. Also conform that the card is properly set. If available, consult manuals or utility software with extension cards. If the error message is still displayed, the PC may be faulty. Contact the Fujitsu service center or a dealer.

  • Page 60: Troubleshooting

    Troubleshooting information on the computer main unit and peripheral units The access lamp does not light up. The PC may be faulty. Contact a dealer or the Fujitsu service center. No data is displayed on the screen. Confirm the following:...

  • Page 61: Troubleshooting Information On Windows 98

    The power is not turned on or the Power lamp on the front panel does not light up. Is the power cable plugged in? Data cannot be read from the CD-ROM drive. Check the following: - Has the CD-ROM been placed properly at the center of the tray? Place the CD-ROM on the tray again with the label side facing upward.

  • Page 62: If An Error Recurs

    SCSI unit is turned on, the SCSI unit cannot be identified. If an error recurs If the cause is still unknown or the system cannot be reset, contact a dealer or the Fujitsu service center. Then check and record the following: - Model name and serial number of the computer (See the label at the rear of the computer.)

  • Page 63: Appendix

    Appendix This appendix explains how to clean the PC and provides PC main unit specifications.

  • Page 64: Name And Function Of Each Component

    1 Name and Function of Each Component This section explains the name and function of each component of the PC main unit, motherboard/ riser board, and keyboard. Front of the PC main unit Power lamp Floppy disk drive The lamp comes on while the PC main unit is on. Mount a floppy disk in this drive to write data into or read data from a floppy disk.

  • Page 65

    Floppy disk eject button Press this button to eject a floppy disk. 3.5-inch blank panel Remove this panel to add a 3.5-inch internal option. Power switch Press this switch to turn on the PC main unit, put the system into the standby status, or recover the system from the standby status.

  • Page 66: Rear Of The Pc Main Unit

    Rear of the PC main unit Power-switching switch Outlet Connect the power cord of the CRT display. Ventilation holes The heat within the PC main unit is ventilated through these holes. Keep them free. Inlet Connect the power cord of the PC main unit. SPK OUT terminal Connect the speakers.

  • Page 67

    Keyboard connector ( : KEYBOARD) Connect the keyboard cable. Security lock You can connect a security-use cable bought on the market. Ventilation holes The heat within the PC main unit is ventilated through these holes. Keep them free. Parallel connector : PRINTER) Connect the printer cable.

  • Page 68: Inside The Pc Main Unit

    Inside the PC main unit Riser board Connectors for expansion cards and IDE connectors are installed. Internal hard disk IDE-standard hard disk. You can replace it with a hard disk with larger capacity. Power supply unit 3.5-inch expansion bay Install a 3.5-inch expansion bay option such as magneto-optic disk drive and internal hard disk.

  • Page 69: Motherboard/riser Board

    Motherboard/riser board Expansion slot DIMM slot Insert various option cards to extend the Insert a memory module. functions of the PC. The slots are placed in the order of DIMM1 The slots are placed in the order of ISA1 and DIMM2 from the right. (half), ISA2 (full), PCI1 (full), and PCI2 (full) from the right.

  • Page 70: Standard Specifications

    2 Standard Specifications PC main unit specifications Product name DESKPOWER 5000 Pentium III or Celeron BIOS ROM 512 KB (FLASH ROM) System RAM SDRAM DIMM with 168-pin parity (Supporting ECC) Up to 512 MB Floppy disk 3.5-inch disk drive x 1 Hard disk 10.2/20.4GB (Ultra DMA66) or higher capacity CD-ROM...

  • Page 71

    Product name DESKPOWER 5000 Number of Storage Rear: 3.5-inch hard disk (standard feature) bays Front center: 3.5-inch floppy disk drive (standard feature) Front upper: 3.5-inch expansion bay Front middle: 5-inch expansion bay (CD-ROM installed as an option) Front lower: 5-inch expansion bay Power supply/ 100/230 VAC 50/60Hz frequency...

  • Page 72: Lan Adapter Specifications

    LAN adapter specifications LAN controller Intel 82559 Send and receive 3 kB each for send and receive buffer RAM External interface ISO8802-3 100BASE-TX/10BASE-T Transmission media Twisted pair cable (100 Mbps: Category 5, 10 Mbps: Categories 3 to 5) Transmission method Base band Access method CSMA/CD...

  • Page 73: Connector Specifications

    Connector specifications The pin arrangement and signal names of each connector are as follows: CRT connector Pin no. Signal name Direction Description Output Red output GREEN Output Green output BLUE Output Blue output – Not connected 5 to 8 – Ground –...

  • Page 74

    Parallel connector Pin no. Signal name Direction Description STROBE Input/output Strobe DATA0 Input/output Data0 DATA1 Input/output Data1 DATA2 Input/output Data2 DATA3 Input/output Data3 DATA4 Input/output Data4 DATA5 Input/output Data5 DATA6 Input/output Data6 DATA7 Input/output Data7 Input Acknowledge BUSY Input Busy Input Out of paper SELECT...

  • Page 75

    Mouse connector Pin no. Signal name Direction Description DATA Input/output Data – Not connected – Ground – Power supply Input/output Clock – Not connected Keyboard connector Pin no. Signal name Direction Description DATA Input/output Data – Not connected – Ground –...

  • Page 76: Cleaning Method

    3 Cleaning Method How to clean the PC is explained as follows: WARNING Electric shock To prevent electric shock, before cleaning the PC, switch off the PC and all connected units and unplug all power cords. Cleaning the PC main unit - Wipe the PC main unit with a soft dry cloth.

  • Page 77: Cleaning A Floppy Disk Drive

    Remove the ball and clean with water. Reverse the mouse to remove the ball, then clean the ball with water. Clean the inside of the mouse. Wipe the inside of the mouse, the rollers, and the Roller back cover with a damp cloth. Attach the ball and the back cover.

  • Page 78: Supplement

    4 Supplement Peripheral devices and cables When peripheral devices or cables are connected to the PC, use Fujitsu-supplied devices and cables, as some non-Fujitsu devices and cables may not be connectable. Note on using the display The vertical and horizontal lines displayed by a CAD application may appear different in width depending on the setting of the resolution of the display used.

  • Page 79: Display And Power Save Mode

    Windows 98/2000 Set the resolution to 640 x 480 (before replacement of the display). Set the refresh rate to the "adapter default." Terminate Windows and turn off the PC power, then replace the display. If there is no screen display or no display at some resolutoion after the display is replaced without performing the above setting, reinstall the display driver as follows: Start Windows in Safe Mode.

  • Page 80: Wake Up On Lan

    PC is to be connected and use the following type of cable in accordanc with the speed: Use a Fujitsu-supplied cable to minimize network trouble. • 100BASE-TX: Unsealed twisted paired-cable(UTP) at category 5 or a higher data grade •...

  • Page 81: Cd-rom Drive

    CD-ROM drive If a CD-ROM cleaning disk sold separately is used for cleaning, the lens may not be clean. Do not use a CD-ROM cleaning disk. ® Intel processor serial number ® ® Each Intel Pentium III processor contains a serial number that can be read electrically. The processor serial number can be used for information management, resource management, and security improvement on the web.

  • Page 82

    Fujitsu PC (Asia) Pte Ltd 200 Pandan Loop #05-03 Pantech 21 The Computer Centre Singapore 128388 Tel: 65-776 0688 Fax: 65-776 0788 Fujitsu PC (Asia) Pte Ltd (Malaysia Branch) 8th Floor Wisma Damansara Jalan Semantan 50490 Kuala Lumpur Malaysia Tel: 603-253 3997 Fax: 603-253 4245 Website : www.fujitsu-pc-asia.com...

This manual also for:

Deskpower 5000 series

Comments to this Manuals

Symbols: 0
Latest comments: