Main Control Panels; Lock Override; Indicator Lights; Locking Features - HotSpring Vista Owner's Manual

MAIN CONTROL PANEL
The main control panel provides a quick visual check of the spa's status, and allows the user to set the temperature, activate the jets and light,
and lock the temperature and/or spa functions.

INDICATOR LIGHTS

At a glance, the indicator lights are readily visible on the main control panel. The three indicator lights (POWER, READY and CLEAN) work
independently from the rest of the control panel display. That way, even if the control panel is off, you can simply glance at the "READY" indicator
light to determine whether or not your spa is within the range of your set temperature.
Power Indicator: The POWER indicator is 'on' when the spa is properly supplied with power. It also provides a diagnostic function–a blinking
power indicator indicates that the heater high limit has tripped, meaning that either the spa water is above its acceptable temperature range, or a
malfunction has occurred within the spa (such as low circulation due to clogged filters). An 'off' power indicator means that there is a problem with
the spa control box or the power supplied to the spa.
1.4°C)
Ready Indicator: The READY indicator will light when the spa water temperature is within 2-1/2°F ( of the set temperature, and will turn off
when the temperature is outside of that range. If you increase or decrease the temperature setting of the spa, the ready indicator will turn off until
the spa temperature reaches the acceptable range for the new set temperature. Additionally, a blinking READY indicator indicates that a problem
exists with the temperature sensor.
Clean Indicator: The CLEAN indicator lights up when the CLEAN button is pressed. It remains on during the ten-minute clean cycle (used for
water maintenance), then automatically shuts off at the end of the cycle. The JET symbol will also illuminate on the display to indicate that the jet
pump is on.
NOTE: When the SPA LOCK feature is activated, the CLEAN button is disabled. If the CLEAN button will not turn on the jet pump, refer to the
following section and verify that the SPA LOCK is off.

LOCKING FEATURES

The two locking features, TEMPERATURE LOCK and SPA LOCK, are enabled from the main control panel by pressing a specific combination of
buttons. Once enabled, a lock will remain active until the specific button combination is applied to disable the lock. Even if power is disconnected
from the spa and soon thereafter reapplied (such as in a power outage) the lock will remain in place.
SPA LOCK
The SPA LOCK feature deactivates all of the functions of the main and auxiliary control panels. It is generally
used to prevent unwanted use of the spa.
To activate the SPA LOCK, press the LIGHT minus (-) and TEMP minus (-) buttons at the same
time and hold them down until the word SPA and the lock symbol are illuminated on the
display (approximately two seconds).
When the SPA LOCK is activated, if a button is pressed, the control panel will display
the lock symbol and the word SPA for 30 seconds, then turn off.
To deactivate the SPA LOCK, press the LIGHT minus (-) and TEMP minus (-)
buttons at the same time and hold them down until the word SPA and the lock
symbol are no longer illuminated on the display (approximately two seconds).
TEMPERATURE LOCK
The TEMPERATURE LOCK feature deactivates the temperature control function of the
main control panel. All other functions on the main and auxiliary control panels will operate normally. TEMPERATURE LOCK is most often used by
people who do not want others to tamper with or change the set temperature of the spa water.
To activate the TEMPERATURE LOCK, press the LIGHT plus (+) and TEMP plus (+) buttons
at the same time and hold them down until the words SET TEMP, the numerical set
temperature value and the lock symbol are illuminated on the display (approximately two seconds).
When the TEMPERATURE LOCK is activated, the JETS, LIGHT, and CLEAN buttons will
operate normally, and the temperature setting can be viewed but can NOT be changed. If a
temperature button is pressed, the control panel will display the lock symbol and the set
temperature for 30 seconds, then turn off.
To deactivate the TEMPERATURE LOCK, press the LIGHT plus (+) and TEMP plus (+)
buttons at the same time and hold them down until the lock symbol is no
longer illuminated on the display (approximately two seconds).

LOCK OVERRIDE

The Lock Override feature is for spa users who normally keep the set temperature locked. Should the user wish to lock all spa controls
Page 42
Control Panel Operations