PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.
Page 3
User’s Manual of FGSW-2620CS Revision PLANET 24-Port 10/100Mbps with 2 Gigabit TP / SFP Combo Web Smart Switch User's Manual FOR MODELS: FGSW-2620CS(V3) ctober, REVISION: 3.0 (O 2013) Part No.: 2080-A81160-001 - 3 -...
3.1 O ............................... 17 VERVIEW 3.2 M ..........................17 ANAGEMENT ETHOD 3.2.1 Web Management........................... 17 3.2.2 PLANET Smart Discovery Utility..................... 17 3.3 L FGSW-2620CS....................... 19 OGGING ON TO THE 4. WEB MANAGEMENT ................ 20 4.1 L ..........................20 OGIN TO THE WITCH 4.2 S...
Page 5
User’s Manual of FGSW-2620CS 4.6 Q ............................52 ETTING 4.6.1 Priority Mode ........................... 53 4.6.2 Class of Service Configuration......................54 4.6.3 TCP / UDP Port-based QoS ......................56 4.7 S ............................. 58 ECURITY ILTER 4.7.1 MAC Address Filter......................... 59 4.7.2 TCP / UDP Filter ..........................60 4.8 S...
Supports SNMP v1, port mirroring function and IGMP Snooping v1 / v2 ◆ Supports DHCP Option82 and DHCP Relay ◆ Firmware upgrade through Web interface ◆ Configuration upload / download through Web interface ◆ Password setting, IP setting and device description setting through Planet Smart discovery utility ◆ - 7 -...
Page 8
User’s Manual of FGSW-2620CS 19-inch rack mount size ◆ Internal full-ranging power supply suitable for worldwide use ◆ EMI standards complies with FCC, CE class A ◆ - 8 -...
Gigabit TP/SFP combo ports, which can either be 1000Base-T for 10/100/1000Mbps or 1000Base-SX/LX through SFP (Small Factor Pluggable) interface. The LED Indicators are also located on the front panel of the Web Smart Switch. Figure 2-1: FGSW-2620CS Switch Front Panel 2.1.1 LED Indicators System...
The rear panel of the Web Smart Switch indicates an AC inlet power socket, which accepts input power from 100 to 240VAC, 50-60Hz, 0.5A. Figure 2-2: FGSW-2620CS Switch Rear Panel Power Notice: 1. The device is a power-required device, meaning it will not work till it is powered. If your networks should be active all the time, please consider using UPS (Uninterrupted Power Supply) for your device.
Page 13
User’s Manual of FGSW-2620CS Step 5: Supply power to the Web Smart Switch. Connect one end of the power cable to the Web Smart Switch. Connect the power plug of the power cable to a standard wall outlet and then power on the Web Smart Switch.
Page 14
User’s Manual of FGSW-2620CS Figure 2-4 Mounting the Web Smart Switch in a Rack Step 6: Proceed with Steps 4 and 5 under Section 2.3.1 Desktop Installation to connect the network cabling and supply power to your Web Smart Switch.
Page 15
User’s Manual of FGSW-2620CS Approved PLANET SFP Transceivers PLANET Web Smart Switch supports both single mode and multi mode SFP transceivers. The following list of approved PLANET SFP transceivers is correct at the time of publication: ■MGB-SX SFP (1000Base-SX SFP transceiver ) ■MGB-LX SFP (1000Base-LX SFP transceiver )
Page 16
User’s Manual of FGSW-2620CS Figure 2-6 Removing the SFP transceiver Never pull out the module without pulling the lever or the push bolt of the module. Directly pulling out the module with force could damage the module and SFP module slot of the Web Smart Switch.
User can manage the Web Smart Switch by Web Management via a network connection. 3.2.1 Web Management PLANET FGSW-2620CS provides a built-in browser interface. You can manage the Switch remotely by having a remote host with Web browser, such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox.
Page 18
User’s Manual of FGSW-2620CS The following install instructions guide you to running Planet Smart Discovery Utility. 1. Insert Planet Smart Discovery Utility in administrator PC. 2. Run this utility and the following screen appears. Figure 3-1 Planet Smart Discovery Utility Screen If there are two LAN cards or above in the same administrator PC, choose a different LAN card by using the “Select Adapter”...
Figure 3-3. 7. Press “Exit” button to shut down Planet Smart Discovery Utility. 3.3 Logging on to the FGSW-2620CS When you log on to the Web Smart Switch Web interface for the first time, a sign-on string appears and you are prompted for a Web login user name and password.
User’s Manual of FGSW-2620CS 4. WEB MANAGEMENT To modify your PC’s IP domain to the same with Web Smart Switch, use the default IP address (192.168.0.100) to re- motely configure Web Smart Switch through the Web interface. 4.1 Login in to the Switch To access the Web-browser interface, you must first enter the user name and password.
User’s Manual of FGSW-2620CS ◆ System: Provides System configuration of Web Smart Switch. Explained in section 4.2. ◆ Port Management: Provides Port Management configuration of Web Smart Switch. Explained in section 4.3. ◆ VLAN Setting: Provides VLAN Setting configuration of Web Smart Switch.
User’s Manual of FGSW-2620CS Object Description System Information Displays the MAC address, Hardware Version, and Software Version, Device Description. Explained in section 4.2.1. IP Configuration Allows to change the IP subnet address of Web Smart Switch. Explained in section 4.2.2.
User’s Manual of FGSW-2620CS Idle Time Security Set idle time and behavior. Table 4-2 Descriptions of the System Information Web Page Screen Objects 4.2.2 IP Configuration This section provides change in the IP Address, Subnet Mask and Gateway as the screen in Figure 4-5 appears.
User’s Manual of FGSW-2620CS Figure 4-6 Password Setting Web Page Screen The page includes the following fields: Object Description User Name Displays the user name. Password Specifies the new password. The password is not displayed. As it enters a “” corresponding to each character is displayed in the field.
Page 25
User’s Manual of FGSW-2620CS Figure 4-9 Firmware Update Web Page Screen Press “Update” button for start the firmware upgrade process, the screen in Figure 4-10 & 4-11 appears. Figure 4-10 Firmware Update Web Page Screen Figure 4-11 Firmware Update Web Page Screen Press “Browser”...
User’s Manual of FGSW-2620CS Figure 4-14 Firmware Update Web Page Screen 1. It is recommended to use IE 7.0 or FireFox browser tools for firmware upgrade process. 2. Firmware upgrade needs several minutes. Please wait for a while, and don’t power off the Web Smart Switch until the update progress is completed.
User’s Manual of FGSW-2620CS 4.3 Port Management This section provides Port Configuration, Port Mirroring, Bandwidth Control, Broadcast Storm Control and Port Statistics from Web Smart Switch as the screen in Figure 4-16 appears and Table 4-5 describes the system object of Web Smart Switch.
User’s Manual of FGSW-2620CS 4.3.1 Port Configuration This section introduces detailed settings of each port on Web Smart Switch as the screen in Figure 4-17 appears and Table 4-6 describes the Port Configuration objects of Web Smart Switch. Figure 4-17 Port Configuration Web Page Screen...
Page 29
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description Port Allows to choose all or one port of Web Smart Switch for further man- agement. The available options are All & 01 to 26. Speed Mode...
User’s Manual of FGSW-2620CS 4.3.2 Port Mirroring This section introduces detailed settings of Port Mirroring function of Web Smart Switch as the screen in Figure 4-18 appears and Table 4-7 describes the Port Mirroring objects of Web Smart Switch. Figure 4-18 Port Mirroring Web Page Screen...
User’s Manual of FGSW-2620CS 4.3.3 Bandwidth Control This section introduces detailed settings of Bandwidth Control function of Web Smart Switch as the screen in Figure 4-19 appears and Table 4-8 describes the Bandwidth Control objects of Web Smart Switch. Figure 4-19 Bandwidth Control Web Page Screen...
User’s Manual of FGSW-2620CS 4.3.4 Broadcast Storm Control This section introduces detailed settings of Broadcast Storm Control function of Web Smart Switch as the screen in Figure 4-20 appears and Table 4-9 describes the Broadcast Storm Control objects of Web Smart Switch.
Page 33
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description Counter Mode Se- Provides different types of Ethernet traffic counter modes. The available options are shown below: lection Receive Packet & Transmit Packet Collision Count & Transmit Packet Drop Packet &...
User’s Manual of FGSW-2620CS 4.4 VLAN Setting A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network traffic so only members of the VLAN receive traffic from the same VLAN members. Basically, creating a VLAN from a switch is logically equivalent of reconnecting a group of network devices to another Layer 2 switch.
Page 35
User’s Manual of FGSW-2620CS 802.1Q Tag User Priority VLAN ID (VID) 3 bits 1 bits 12 bits TPID (Tag Protocol Identifier) TCI (Tag Control Information) 2 bytes 2 bytes Destination Source Ad- Ethernet Preamble VLAN TAG Data Address dress Type...
Page 36
User’s Manual of FGSW-2620CS Default VLANs The Switch initially configures one VLAN, VID = 1, called "default." The factory default setting assigns all ports on the Switch to the "default". As new VLAN are configured in Port-based mode, their respective member ports are removed from the "default."...
User’s Manual of FGSW-2620CS 4.4.1 802.1Q VLAN This section introduces detailed information of IEEE 802.1Q VLAN function of Web Smart Switch. Choose “802.1Q VLAN” from VLAN from the VLAN Mode and press “Apply” button to enable the 802.1Q VLAN function as the screen in Figure 4-23 &...
Page 38
User’s Manual of FGSW-2620CS Group Displays the existence of 802.1Q VLAN groups. VID Displays different VLAN IDs from multi-802.1Q VLAN groups. VLAN Name Assigns and displays different VLAN names from multi-802.1Q VLAN groups. Up to maximum 8 characters allow.
Page 39
User’s Manual of FGSW-2620CS Figure 4-25 802.1Q VLAN Per Port Setting Web Page Screen This section introduces detailed information of IEEE 802.1Q VLAN Per Port Setting of Web Smart Switch as Table 4-13 describes the 802.1Q VLAN Per Port Setting objects of Web Smart Switch.
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description Indicates port 1 to port 26. Port Defines UnTag or Tag on each port of Web Smart Switch. Default mode is Link Type “UnTag”. Defines No Uplink or Uplink on each port of Web Smart Switch. Default mode is Uplink “No Uplink”.
Page 41
User’s Manual of FGSW-2620CS While [PC-1] transmits an untagged packet enters Port-1, the Web Smart Switch will tag it with a VLAN Tag=2. [PC-2] and [PC-3] will receive the packet through Port-2 and Port-3. [PC-4], [PC-5] and [PC-6] receive no packet.
Page 42
User’s Manual of FGSW-2620CS Figure 4-27 Assign VLAN members to VLAN 2 and VLAN 3 Please remember to remove Port 1 – Port 6 from VLAN 1 membership, since Port 1 – Port 6 has been assigned to VLAN 2 and VLAN 3.
Page 43
User’s Manual of FGSW-2620CS Figure 4-28 Remove specified ports from VLAN 1 member It’s important to remove the VLAN member port from VLAN 1 group or else the ports would become overlapping setting. Assign PVID for each port: Port-1,Port-2 and Port-3 : PVID=2.
Page 44
User’s Manual of FGSW-2620CS Figure 4-29 Port 1-Port 6 802.1Q VLAN Configuration Two separate 802.1Q VLANs with overlapping area scenario Based on the two separate VLAN group examples shown above, VLAN 2 and VLAN 3 member porst cannot see each other.
Page 45
User’s Manual of FGSW-2620CS Figure 4-31 VLAN overlapping port setting Define a VLAN 1 as a “Public Area” that overlaps with both VLAN 2 members and VLAN 3 members. - 45 -...
Page 46
User’s Manual of FGSW-2620CS Figure 4-32 VLAN 1 – The public area member assigned Set up Port-7 with “PVID=1” on VLAN Per Port Configuration page as the screen in Figure 4-33 appears. Figure 4-33 Setting up of Port-7 with PVID-1...
User’s Manual of FGSW-2620CS Although the VLAN 2 members: Port-1 to Port-3 and VLAN 3 members: Port-4 to Port-6 also belongs to VLAN 1. But with different PVID settings, packets form VLAN 2 or VLAN 3 is not able to access to the other VLAN.
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description VID Displays different VLAN IDs from multi-port based VLAN groups. VLAN Name Assigns and displays different VLAN names from multi-port based VLAN groups. Up to maximum 8 characters allowed.
Page 49
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description MTU Port Indicates the MTU Port of Web Smart Switch. Member Port Indicates the Member Port of Web Smart Switch. Apply Button Press this button to save the current configuration of Web Smart Switch.
User’s Manual of FGSW-2620CS 4.5 Trunk Port link aggregations can be used to increase the bandwidth of a network connection or to ensure fault recovery. Link aggregation lets you group up to 4 consecutive ports into a single dedicated connection between any two the Switch or other Layer 2 switches.
User’s Manual of FGSW-2620CS Trunk Setting This function allows to configure the trunk function. It provides up to two trunk groups and each trunk group provides 4 member ports. It also provides four various Trunk Hash Algorithm policies for selection as the screen in...
User’s Manual of FGSW-2620CS Default link group 3 includes P25, P26. State Allows to disable or enable port trunk from Web Smart Switch. The available options are Enable and Disable. Default mode is Disable. Type Allows to select port trunk type from Web Smart Switch. The available options are LACP and Static.
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description Priority Mode Provides three different Priority polices on Web Smart Switch , explained in section 4.6.1. Class of Service Provides three different polices on each port of Web Smart Switch , ex- plained in section 4.6.2.
User’s Manual of FGSW-2620CS 4.6.2 Class of Service Configuration This section introduces detailed information of Class of Service Configuration of Web Smart Switch as the screen in Figure 4-40 appears and Table 4-20 describes the Class of Service Configuration of Web Smart Switch.
Page 55
User’s Manual of FGSW-2620CS VLAN Priority tag value define IEEE 802.1p priority value from VLAN tag High Priority User priority values= 4~7 Low Priority User priority values= 0~3 IP TOS/DSCP Priority value define TOS/DSCP Value AF11 AF21 AF31...
User’s Manual of FGSW-2620CS 4.6.3 TCP / UDP Port Based QoS This section introduces detailed information of TCP / UDP Port-based QoS Configuration of Web Smart Switch as the screen in Figure 4-41 appears and Table 4-21 describes the TCP / UDP Port-based QoS Configuration of Web Smart Switch.
Page 57
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description Protocol Displays different Protocols to define optional QoS policy FTP(20,21) Provides F-I-F-O, Discard, Low, High options. SSH(22) Provides F-I-F-O, Discard, Low, High options. TELNET(23) Provides F-I-F-O, Discard, Low, High options.
User’s Manual of FGSW-2620CS 4.7 Security Filter This function provides Security Filter of Web Smart Switch as the screen in Figure 4-42 appears and Table 4-22 describes the Security Filter of Web Smart Switch. Figure 4-42 Security Filter Web Page Screen...
User’s Manual of FGSW-2620CS 4.7.1 MAC Address Filter This section introduces detailed information of MAC Address Filter of Web Smart Switch as the screen in Figure 4-43 appears and Table 4-23 describes the MAC Address Filter of Web Smart Switch.
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description MAC Address Allows to input three MAC Addresses on each port of Web Smart Switch. Select Port Allows to select port 1 to port 26. Binding Allows to disable or enable the binding function on each port of Web Smart Switch.
Page 61
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description Function Enable Allows to Disable or Enable the TCP / UDP Filter function. Default mode is Disable. Port Filtering Rule Allows to Forward or Block the Port Filtering Rule. Default mode is Block.
User’s Manual of FGSW-2620CS 4.8 Spanning Tree This function provides Spanning Tree of Web Smart Switch as the screen in Figure 4-45 appears and Table 4-25 describes the Spanning Tree of Web Smart Switch. Figure 4-45 Spanning Tree Web Page Screen...
User’s Manual of FGSW-2620CS 4.8.1 STP Bridge Setting This section introduces detailed information of STP Bridge Setting of Web Smart Switch as the screen in Figure 4-46 appears and Table 4-26 describes the STP Bridge Setting Configuration of Web Smart Switch.
Page 64
User’s Manual of FGSW-2620CS Enter a value between 6 through 40. Forward Delay The number of seconds a port waits before changing from its Rapid Spanning-Tree Protocol learning and listening states to the forwarding state. Enter a value between 4 through 30.
User’s Manual of FGSW-2620CS 4.8.2 STP Port Setting This section introduces detailed information of STP Port Setting of Web Smart Switch as the screen in Figure 4-47 appears Table 4-27 describes the STP Port Setting Configuration of Web Smart Switch.
Page 66
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description Port No. Allows to choose one port of Web Smart Switch for further management. The available options are 01 to 26. Priority (0~240) Decide which port should be blocked by setting its priority as the lowest.
User’s Manual of FGSW-2620CS 4.8.3 Loopback Detection Setting This section introduces detailed information of Loopback Detection Settings of Web Smart Switch as the screen in Figure 4-48 appears and Table 4-28 describes the Loopback Detection Setting Configuration of Web Smart Switch.
Page 68
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description Loopback Detect Allows to Disable or Enable the Loopback Detect Function. Default mode is Disable. Function Auto Wake Up Allows to Disable or Enable the Auto Wake Up function. Default mode is Disable.
User’s Manual of FGSW-2620CS 4.9 DHCP Relay Agent This function provides DHCP Relay Agent of Web Smart Switch as the screen in Figure 4-49 appears and Table 4-29 describes the DHCP Relay Agent of Web Smart Switch. Figure 4-49 DHCP Relay Agent Web Page Screen...
User’s Manual of FGSW-2620CS 4.9.1 DHCP Relay Agent This section introduces detailed information of DHCP Relay Agent of Web Smart Switch as the screen in Figure 4-50 appears and Table 4-30 describes the STP Bridge Setting Configuration of Web Smart Switch.
User’s Manual of FGSW-2620CS The page includes the following fields: Object Description DHCP Server IP Assign the DHCP Server IP address. Table 4-31 Descriptions of the STP Bridge Setting Configuration Screen Objects 4.9.3 VLAN MAP Relay Agent This section introduces detailed information of VLAN MAP Relay Agent of Web Smart Switch as the screen in...
User’s Manual of FGSW-2620CS 4.10 Misc Operation This function provides Misc Operation of Web Smart Switch as the screen in Figure 4-53 appears and Table 4-33 scribes the Misc Operation of Web Smart Switch. Figure 4-53 Misc Operation Web Page Screen...
User’s Manual of FGSW-2620CS 4.11 Backup/Recovery This function provides Backup/Recovery of Web Smart Switch as the screen in Figure 4-54 appears and Table 4-34 scribes the Backup/Recovery of Web Smart Switch. Figure 4-54 Backup/Recovery Web Page Screen The page includes the following fields:...
User’s Manual of FGSW-2620CS 4.12 SNMP Setting This function provides SNMP Setting of Web Smart Switch as the screen in Figure 4-55 appears and Table 4-35 describes the SNMP Setting of Web Smart Switch. Figure 4-55 SNMP Setting Web Page Screen...
User’s Manual of FGSW-2620CS 4.13 Logout This section provides Web logout function on Web Smart Switch after choosing this function and the following screen appears in Figure 4-56. Please press “Logout” button to take effect and Login Web Screen appears. Please re-login the Web Smart Switch for further management.
User’s Manual of FGSW-2620CS 5. SWITCH OPERATION 5.1 Address Table The Switch is implemented with an address table. This address table is composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Ethernet Switch.
User’s Manual of FGSW-2620CS 5.5 Auto-Negotiation The STP ports on the Switch have built-in "Auto-negotiation". This technology automatically sets the best possible bandwidth when a connection is established with another network device (usually at Power On or Reset). This is done by detecting the modes and speeds at the second of both devices connected.
Check the LNK/ACT LED on the switch Try another port on the Switch. Make sure the cable is installed properly. Make sure the cable is the right type. Turn off the power. After a while, turn on the power again. How to deal with the forgotten password situation of FGSW-1820CS / FGSW-2620CS Solution:...
Page 80
User’s Manual of FGSW-2620CS The standard RJ-45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Straight Cable SIDE 1...
*Model Number: FGSW-2620CS * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.) is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2004/108/EC).