Table of Contents
Advertisement
Quick Links
CHAPTER 1. INTRODUCTION ...................................................1
1-1 About the Switch.................................................................1
1-2 Feature ...............................................................................2
1-3 Package Contents...............................................................3
CHAPTER 2. HARDWARE DESCRIPTION...............................5
2-1 Physical Description ..........................................................5
2-2 Front & Rear Panel............................................................5
2-3 Module LED Indicators......................................................6
2-4 Dual Power LEDs ..............................................................6
CHAPTER 3. MODULES...............................................................7
3-1 Optional Modules...............................................................7
3-2 8-port 10/100 N-Way Switch Module ..............................7
3-2-1 Features: ......................................................................8
3-2-2 DIP-Switch with Link Mode.........................................8
3-2-3 LED Indicators ............................................................9
3-3 2/4-Port 100Base-FX( SC/ST ) Switch Module .............10
3-3-1 Features: ....................................................................10
3-3-2 DIP-Switch with Link Mode....................................... 11
3-3-3 LED Indicators .......................................................... 11
3-4 4/ 8-Port 100Base-FX (MT/VF) Switch Module ...........12
3-4-1 Features .....................................................................13
3-4-2 DIP-Switch with Link Mode.......................................13
Table of Content
Advertisement
Table of Contents
Related Manuals for Planet FGSW-008
Summary of Contents for Planet FGSW-008
-
Page 1: Table Of Contents
Table of Content CHAPTER 1. INTRODUCTION ...........1 1-1 About the Switch..............1 1-2 Feature ................2 1-3 Package Contents...............3 CHAPTER 2. HARDWARE DESCRIPTION.......5 2-1 Physical Description ............5 2-2 Front & Rear Panel............5 2-3 Module LED Indicators............6 2-4 Dual Power LEDs ..............6 CHAPTER 3. MODULES...............7 3-1 Optional Modules...............7 3-2 8-port 10/100 N-Way Switch Module ......7 3-2-1 Features: ..............8... - Page 2 3-4-3 LED Indicators ............14 3-5 Gigabit 1000Base-SX/LX Switch Modules ....15 3-5-1 Features ..............15 3-5-2 DIP Switch with Link Mode ........15 3-5-3 LED Indicators ............16 3-6 Gigabit 10/100/1000Base-T Switch Module ....17 3-6-1 Features ..............17 3-6-2 LED Indicators ............18 3-6-3 Installing Optional Modules ........18 CHAPTER 4.
-
Page 3: Fcc Warning
Copyright PLANET Technology Corp. 2001. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. FCC Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 4: Chapter 1. Introduction
Chapter 1. Introduction 1-1 About the Switch Congratulations on purchasing the Chassis Switch FGSW-008. The Switch is a combination of 8 slot host cabinet which can optional a lot of kinds of media modules to fit your networking needs. A maximum 64X 10/100 Base-TX switched ports can be achieved using 8X 8 port 10/100Base-TX switch module. -
Page 5: Feature
This chapter gives an overview of the Switch and it covers the following items: About the switch Features Package contents 1-2 Feature The 8-expansion slots can flexible configure your network. It can be 64 ports 10/100Base-TX switch, 32 ports 100Base-FX(SC/ST) switch, 64 ports 100Base-FX(MT-RJ/VF-45) switch or 8 ports Gigabit Switch. -
Page 6: Package Contents
Compare the contents of your FGSW switch package with the standard checklist above. If any item is missing or appears damaged, please keep the carton and original packaging materials if possible in case you need to return the switch for repair. FGSW-008 User's Manual... - Page 7 This page is intentionally left blank Gigabit Chassis Switch...
-
Page 8: Chapter 2. Hardware Description
Gigabit Modules. Figure 2-1. Front Panel The 3-pronged power plug and On/off switched are located at the Rear Panel of the Switch displayed in Figure 2-2. The Switch will work with AC in the range 100-240VAC, 50-60Hz. FGSW-008 User's Manual... -
Page 9: Module Led Indicators
Figure 2-2. Rear Panel 2-3 Module LED Indicators All LED status indicators are located on the FRONT panel of the switches. They provide a real-time indication of system and operational status. The ports for connections to other devices and networks are also on the front panels. The following sections provide descriptions of the LED indicators and ports. -
Page 10: Chapter 3. Modules
1000Mbps technology is now a simple matter of slotting in the desired module. By mixing different modules in the same cabinet, the user ensures network performance and budget requirements are easily met. 3-2 8-port 10/100 N-Way Switch Module FGSW-8TP(V.x) Figure 3-1. 8-port 10/100 N-Way Module Front View FGSW-008 User's Manual... -
Page 11: Features
Please make sure the version of the module before slide-in it to the slot. Use of module FGSW-8TP could cause LED indication abnormal in FGSW-008. The accepted one is version 2 or above. The version number can be found besides the serial number with format: FGSW-8TP (V.x). -
Page 12: Led Indicators
Full-duplex mode. When the corresponding port is operating in Half-duplex mode, the LED indicator is not lit. When collisions are occurring at the corresponding port, the LED indicator blinks. FGSW-008 User's Manual... -
Page 13: 2/4-Port 100Base-Fx( Sc/St ) Switch Module
3-3 2/4-Port 100Base-FX( SC/ST ) Switch Module FGSW-4SC / FGSW-4ST Figure 3-3. 4 port 100Base-FX ( SC ) Module Front View Figure 3-4. 4 port 100Base-FX ( ST ) Module Front View 3-3-1 Features: 2/4 X 100Mbps fiber ports (SC/ST connectors) Up to 2.4Gbps Backplane forwarding rate 2MB memory buffer 12K-entry MAC Address Table Store-and-forward technology for abnormal packet filtering... -
Page 14: Dip-Switch With Link Mode
The following Table lists the port's operating modes based on the DIP- switch position. Half-Duplex Full-Duplex 3-3-3 LED Indicators There are two LED indicators for each of the Fiber connection ports. If there is no connection to a port, the corresponding LED indicators are not lit. FGSW-008 User's Manual... -
Page 15: 4/ 8-Port 100Base-Fx (Mt/Vf) Switch Module
LK/ACT The LED indicator is green when there is a connection secured to a device ( Link ) to the corresponding port . This LED indicator blinks when there is a data transmission ( Activity ) taking place at the corresponding port. FD/COL The LED indicator is yellow... -
Page 16: Features
LED indicators show the status of the Module at a glance. A DIP-switch sets the operating mode to half-duplex or full-duplex ( default ). Figure 3-8. DIP-switch location and setting mode of FGSW-4MT/4VF FGSW-008 User's Manual... -
Page 17: Led Indicators
The following Table lists the port's operating modes based on the DIP- switch position. Half-Duplex Full-Duplex 3-4-3 LED Indicators There are two LED indicators for each of the Fiber connection ports. If there is no connection to a port, the corresponding LED indicators are not lit. -
Page 18: Gigabit 1000Base-Sx/Lx Switch Modules
If you set DIP switch to Enable N-way, then the other DIP for Half-Duplex and Full Duplex is invalid. If you set DIP switch to Disable N-way, then to set the other DIP between Half-Duplex and Full-Duplex. FGSW-008 User's Manual... -
Page 19: Led Indicators
Figure 3-10. DIP-switch location and setting mode of Gigabit Fiber Module 3-5-3 LED Indicators The are four LED indicators for one Gigabit Fiber connection port. If there is no connection to a port, the corresponding LED indicators are not lit. LK The LED indicator is green when there is a connection securely to a device ( Link ) to the corresponding port. -
Page 20: Gigabit 10/100/1000Base-T Switch Module
Automatic MDI crossover function Up to 2.4Gbps Backplane forwarding rate 2MB memory buffer sharing 12K-entry Mac Address Table Store-and-forward technology for abnormal packet filtering Half-duplex and full-duplex modes supported LED-indicators for 1000M Link, 100M Link, Activity, and Full-duplex statuses FGSW-008 User's Manual... -
Page 21: Led Indicators
3-6-2 LED Indicators The are 4 LED indicators for one RJ-45 connection port. If there is no connection to a port, the corresponding LED indicators are not lit. LK1000 The LED indicator is green when the Port is linking with 1000Mbps mode. When the port is operating in 10Mbps mode or not connected, the LED indicator is not lit. - Page 22 6. Take off the dust cover from the transceiver and plug the cable in, if you are installing a fiber optic or gigabit module. 7. Check the LEDs to verify that if there is a link and a FGSW-008 User's Manual...
- Page 23 proper connection at the port. This page is intentionally left blank Gigabit Chassis Switch...
-
Page 24: Chapter 4. Installation
A dry cool place: Keep the switch away from moisture. Avoid direct sunlight, heat source, and high amount of electromagnetic interference around. Mounting tools: If you intend to mount the switch on a rack, make sure you have all the tools, mounting brackets, screws, bolts and nuts. FGSW-008 User's Manual... -
Page 25: Mounting The Switch
Cauti Cabling must be away from sources of electrical noise such as radio, computers, transmitters, broadband amplifiers, power lines and keep away from TVs, hair dryers, and microwave. Air flow around the switch and through its vents on the rear cannot be restricted. 4-2 Mounting the Switch The Switch is suitable for use in an office environment where it can be rack-mounted in standard EIA 19-inch racks or standalone. - Page 26 After attached both mounting brackets, position the switch in the rack by lining up the holes in the brackets with the appropriate holes on the rack. Secure the switch to the rack with a screwdriver and the supplied rack-mount screws. FGSW-008 User's Manual...
-
Page 27: Power On
Figure 4-2: Rack Mount the Switch Note: For proper ventilation, allow about 6 inches of clearance on the front and 6 inches on the back of the Switch. This is especially important for enclosed rack installations. Apply the procedures to stack more RFS switches. To remove a rack, use a screwdriver for loosening all the screws on the rack and the stacking brackets from the body. -
Page 28: Chapter 5. Planning Your Network
Also, switch can forward multiple data transaction at once. To expand your network topology or enhance network performance, you can use the Switch as collapsed backbone or to increase file server performance, to be segment large network, or to interconnect Gigabit network. FGSW-008 User's Manual... -
Page 29: Modularized Switch Application
5-1 Modularized Switch Application In general, the Switch is designed to be a modularized switch. The Switch can contain different kinds of connecting ports including RJ-45, SC/ST /MT-RJ /VF-45 fiber port, SX/LX Gigabit fiber port. These ports enable the flexibility of your network configuration. You can use the switch to connect PCs, workstations, and servers to each other by connecting these devices directly to the switch. -
Page 30: Backbone Switch Application
The Switch is ideally suited as a workgroup switch in a network. With a Gigabit Fiber Module, for example, installed in the Switch, the entire switched topology could be connected to server as a backbone switch. Figure 5-2. Backbone Switch Application FGSW-008 User's Manual... -
Page 31: Departmental Bridge Application
5-3 Departmental Bridge Application Connecting the server to the 100Mbps port allows a large of users to access the server without causing network congestion. That is, with its large address table (12K MAC address) and high performance, it is ideal for interconnecting network segments -simply connect the network hubs that from those segments to the Switch. -
Page 32: Technical Specifications
10Base-T: 2-pair UTP Cat. 3, 4, 5 cable (100m), Network Cables EIA/TIA-568 100-hm STP (100m) 100Base-TX: 2-pair UTP Cat. 5 cable (100m),EIA/TIA-568 100-ohm STP (100m) 100Base-FX: 50, 62.5/125 micron multi-mode fiber-optics (2Km) 1000Base-FX: 50, 62.5/125 micron multi-mode fiber-optics(500m) 10/125 micron single-mode fiber-optics (10Km) FGSW-008 User's Manual... - Page 33 Dimensions 440mm x 266mm x 133mm (L x W x H) Operating 0ºC to 45ºC (32ºF to 113ºF) Temperature Operating 10% to 90% (Non-condensing) Humidity Redundant Input rate: 100~240VAC, 50~60Hz Power Supply Internal universal power supply: DC 3.3V/25A, 5V/4A Power 62~86 Watt depended on modules Consumption FCC Class A, CE Mark...
Need help?
Do you have a question about the FGSW-008 and is the answer not in the manual?
Questions and answers