Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications, and makes no warranty and representation, either implied or expressed, with respect to the quality, performance, merchantability, or fitness for a particular purpose.
Do not dispose of WEEE as unsorted municipal waste; WEEE has to be collected separately. Revision PLANET 8-Port 10/100Mbps 802.3af PoE + 1-Port 10/100/1000Mbps Desktop Switch User’s Manual For Model: FGSD-910P Revision: 1.0 (JUNE, 2013)
Perfectly Integrated Solution for IP PoE Camera and NVR System Different from the general IT industrial PoE Switch which usually comes with 12 or 24 PoE ports, the FGSD-910P provides 8 802.3af PoE ports for catering to small...
IP Surveillance networks at a lower total cost. The FGSD-910P comes with high performance switch architecture and 130-watt PoE power budget. The recorded video files from 8 PoE IP Cameras can be powered by FGSD-910P and saved in the 8-channel NVR system or surveillance software to perform comprehensive security monitoring.
LED indicators for system Power, per port PoE ready and PoE activity, speed, Link / Act 1 silent FAN to provide stable and efficient power performance 1.4 Specifications Model FGSD-910P Hardware Specification 8-Port RJ-45 for 10/100Base-TX (Port 1 to Port 8) Network Connector 1-Port RJ-45 for 10/100/1000Base-T (Port 9) PoE Inject Port 8-Port with 802.3af PoE injector function...
Page 8
System: Power (Green) Per PoE port: PoE (Orange) LED Display LNK/ACT (Green) Gigabit port: Speed (Green) LNK/ACT (Green) Switch Architecture Store and Forward switch architecture MAC Address Table 4K MAC address table with Auto learning function Switch Fabric 3.6Gbps Switch Throughput 2.67Mpps@64Bytes Back pressure for Half-Duplex.
2.1 Front Panel The Front Panel of the FGSD-910P PoE Ethernet Switch consists of 8x Auto-Sensing 10/100Mbps Ethernet RJ-45 Ports and 1x Auto-Sensing 10/100/1000Mbps Ethernet RJ-45 Port. The LED Indicators are also located on the front panel of the FGSD- 910P.
Blink: Indicate that the Switch is actively sending or receiving data over that port. 2.2 Rear Panel The rear panel of the FGSD-910P indicates an AC inlet power socket, which accepts input power from 100 to 240V AC, 50-60Hz, 2A. 100~240V AC 50/60Hz, 2A max.
1000Base-T, 100Base-TX and 10Base-T networks. Users only need to plug a working network device into the 10/100/1000Base-T port, and then turn on the FGSD-910P. The port will automatically run in 10Mbps, 20Mbps, 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after negotiating with the connected device.
Step 2: Place the PoE Ethernet Switch on desktop near an AC power source. Step 3: Keep enough ventilation space between the PoE Ethernet Switch and the surrounding objects. When choosing a location, please keep in mind the environmental restrictions discussed in Chapter 1, Section 4 under Specification. Note Step 4: Connect your PoE Ethernet Switch to 802.3af complied Powered Devices (PD) and other network devices.
Page 13
8- Po rt 10 /1 00 M bp s+ 1 G ig ab it 80 2. 3a Po E Sw itc h FG SD -91 Figure 2-4: Attaching the Brackets to the PoE Ethernet Switch You must use the screws supplied with the mounting brackets. Damage caused to the parts by using incorrect screws would invali- date the warranty.
2.5.1 802.3af PoE IP Surveillance in Public Transportation Providing up to eight 802.3af PoE, in-line power interfaces and 1 Gigabit TP interface, the FGSD-910P can easily build a power centrally controlled IP Camera system for the enterprises. It can work with 8-channel NVR and surveillance software to perform comprehensive security monitoring.
Ethernet cable from the connected FGSD-910P. The Wireless AP group, PoE IP Phones and Analog Telephony Adapter work perfectly with the FGSD-910P which injects power through the Ethernet cables. With the FGSD-910P, IP Telephony deployment becomes more reliable and cost effective, which helps enterprises save tremendous cost when upgrading from the traditional telephony system to IP Telephony communications infrastructure.
AC wiring and reduces 3~12 watts the installation time. Since the FGSD-910P per PoE port supports 48V DC PoE power output, please check and assure the Powered Device’s (PD) accept- able DC power range is from 48V DC. Otherwise, it will damage the Note Powered Device (PD).
3. Power over Ethernet Overview What is PoE? The PoE is an abbreviation of Power over Ethernet; the PoE technology means a system to pass electrical power safely, along with data on Ethernet UTP cable. The IEEE standard for PoE technology requires Category 5 cable or higher for high power PoE levels, but can operate with category 3 cable for low power levels.
Page 18
(although IEEE 802.3af refers to it as endpoint). Otherwise, if it's an intermediary device between a non PoE capable switch and a PoE device; it's called a Mid-span. An external PoE injector is a Mid-span device. Powered device A powered device (PD) is a device powered by a PSE and thus consumes energy. Examples include wireless access points, IP Phones, and IP cameras.
Page 19
The data pairs are used. Since Ethernet pairs are transformer coupled at each end, it is possible to apply DC power to the center tap of the isolation transformer without upsetting the data transfer. In this mode of operation the pair on pins 3 and 6 and the pair on pins 1 and 2 can be of either polarity.
Why I connect my PoE device to FGSD-910P and it cannot power on Solution: 1. Please check the cable type of the connection from the FGSD-910P (port 1 to port 8) to the other end. The cable should be an 8-wire UTP, Category 5 or above, EIA568 cable within 100 meters.
Appendix: A Networking Connection A.1 PoE RJ-45 Port Pin Assignments PIN NO RJ-45 POWER ASSIGNMENT Power + 1 2 3 4 5 6 7 8 Power + Power - Power - A.2 Switch's Data RJ-45 Pin Assignments - 1000Mbps, 1000Base-T PIN NO MDI-X BI_DA+...
A.3 10/100Mbps, 10/100Base-TX When connecting your PoE Ethernet Switch to another Fast Ethernet switch, a bridge or a hub, a straight or crossover cable is necessary. Each port of the Switch supports auto-MDI/MDI-X detection. That means you can directly connect the Switch to any Ethernet devices without making a crossover cable.
Page 23
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation and color of straight cable and crossover cable connection: SIDE 1 SIDE 2 Straight Cable 1 = White/Orange 1 = White/Orange SIDE 1 2 = Orange 2 = Orange...
: FGSD-910P * Produced by: Manufacturer‘s Name : Planet Technology Corp. Manufacturer‘s Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.). is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2004/108/EC).