Da-Lite Tensioned Conference Electrol Specifications

Tensioned Conference Electrol
Automatic Electric Projection Screen Model
SUGGESTED SPECIFICATIONS:
(H) x (W). Tensioned Conference Electrol® screen shall
have three motors, one to operate door, one to operate screen and one to
operate document camera arm. Door motor electrically operated 120 volt (60
Hz) not more than 1.2 amp. Shall have motor mounted inside the roller, to be
three wire with ground, quick reversal type, oiled for life, with automatic ther-
mal overload cutout, integral gears, capacitor and an electric brake to prevent
coasting. To have pre-set but adjustable limit switches to automatically stop
fabric door in the " down" position. The door will lift to the closed position
where an internal micro-switch will cut off the electrical current to the door
motor. The roller to be of rigid aluminum. Screen motor is electrically operated
120 volt (60 Hz) not more than 2.4 amp. Shall have motor mounted inside the
roller, to be three wire with ground quick reversal type, oiled for life, with auto-
matic thermal overload cutout, integral gears, capacitor and an electric brake
to prevent coasting. To have pre-set but adjustable limit switches to automati-
cally stop picture surface in the "up" and "down" positions. The roller to be of
rigid metal. Camera arm motor is electrically operated 120 volt (60 Hz) not
more than 2.4 amp. Shall have motor mounted inside the roller, to be two wire
with ground quick reversal type, oiled for life, with automatic thermal overload
cutout, integral gears, capacitor and an electric brake to prevent coasting. To
have pre-set but adjustable limit switches to automatically stop the camera
Viewing Area (H x W)
In. Cm
45" x 80" 114 x 203
52" x 92" 132 x 234
54" x 96" 137 x 244
58" x 104" 147 x 264
65" x 116" 165 x 295
Viewing Area (H x W)
In. Cm
50" x 80" 127 x 203
571⁄2" x 92" 146 x 234
60" x 96" 152 x 244
65" x 104" 165 x 264
69" x 110" 175 x 279
721⁄2" x 116" 184 x 295
PRODUCT NOTES
• All viewing surfaces will be seamless.
• All viewing surfaces are standard with black
backing.
• *All screens standard with 12" (30 cm) black drop at
top except the 69" x 110", which has 101⁄2" (27 cm),
and the 721⁄2" x 116", which has 7" (18 cm).
• Custom formats and sizes available upon request.
Contact Da-Lite for feasibility.
• Overall case length dimensions +/- ¼" (6 mm).
• Detail dimensional drawings, wiring diagrams and
installation instructions available upon request.
• Specifications subject to change without notice.
projection screen(s),
HDTV (16:9) Format Dimensions
Nominal Diagonal Maximum Drop*
In. Cm In.
92" 234 19"
106" 269 12"
110" 279 251⁄2"
119" 302 211⁄2"
133" 338 141⁄2"
Wide (16:10) Format Dimensions
Nominal Diagonal Maximum Drop*
In. Cm In.
94" 239 14"
109" 277 221⁄2"
113" 287 191⁄2"
123" 312 141⁄2"
130" 330 101⁄2"
137" 348 7"
®
arm in the "up" and "down" positions. Screen fabric to be seamless, flame retar-
dant and mildew resistant vinyl, with black masking borders standard. Each
side of the fabric to have tab guide cable system to maintain even lateral ten-
sion and hold surface flat. Custom slat bar with added weight maintains
vertical tension on the screen surface. The ends of the slat to be protected by
heavy duty plastic caps enclosing a preset adjustable mechanism for screen
tensioning. Case shall be constructed of ¾" medium density fiberboard.
Bottom of case to be self-trimming with a built-in flange around the bottom of
the case. A section of the bottom of the case shall be an aluminum door
equipped with hinges so that it opens and closes automatically with the lower-
ing and raising of the picture surface. The balance of the bottom of the case
shall be a second hinged aluminum door with manual opening to provide
access. Hinges shall be mounted in a concealed way. Junction box shall be
internally integrated into the housing making it possible to install the housing
and wire to the building's electrical system during construction. The junction
box shall contain a quick connect connector that is mounted in the housing
for easy plug-in connection to the motorized fabric and roller assembly. The
motorized fabric and roller assembly to be installed in the case at the factory
or at a later time at the job site. To be complete with integrated low voltage
control unit and three position control switch and cover plate.
Overall Length of Case
Cm In.
48 120"
30 120"
65 1431⁄8"
55 1431⁄8"
37 1431⁄8"
Overall Length of Case
Cm In.
36 120"
57 1431⁄8"
50 1431⁄8"
37 1431⁄8"
27 1431⁄8"
18 1431⁄8"
WHEN ORDERING, MARK APPROPRIATE SELECTIONS
1. Select size from charts below.
2. Select viewing surface (All Da-Lite surfaces are GREENGUARD GOLD Certified.):
HD Progressive 0.6
HD Progressive 0.9
HD Progressive 1.1
Da-Mat®
3. Optional accessories:
Wireless Remote Control for LVC.
Radio Frequency Remote
Radio Frequency Range
Extender available
Infrared Remote
Key Locking Cover Plate for LVC Switch.
Weight.
Cm Lbs. Kg
305 ]325 147.4
305 340 154.2
364 378 171.5
364 383 173.7
364 396 179.6
Weight.
Cm Lbs. Kg
305 326 147.9
364 378 171.5
364 381 172.8
364 384 174.2
364 390 176.9
364 403 182.8
High Contrast Da-Mat®
Pearlescent
Cinema Vision
High Contrast Cinema Vision
220/240 Volt (50 Hz) motor.
Video Projector Interface Control
– built-in
Plenum Enclosure – For use in
environmental air space.
SPECIFICATION DATA
Approx. Ship. Wt.
Lbs. Kg
569 258.1
584 264.9
662 300.3
667 302.5
680 308.4
Approx. Ship. Wt.
Lbs. Kg
570 258.5
662 300.3
665 301.6
668 303.0
674 305.7
687 311.6