Da-Lite Tensioned Director Electrol Instruction Book
  1. Manuals
  2. Brands
  3. Da-Lite Manuals
  4. Projection Screen
  5. Tensioned Director Electrol
  6. Instruction book

Da-Lite Tensioned Director Electrol Instruction Book

Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Book For
Tensioned Director Electrol
The
POWER
In
PRESENTATION PRODUCTS
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 219/267-8101
800-622-3737
Fax: 219/267-7804
http:// www.da-lite.com
e-mail: info@da-lite.com

Advertisement

Table of Contents
loading

Related Manuals for Da-Lite Tensioned Director Electrol

Summary of Contents for Da-Lite Tensioned Director Electrol

  • Page 1 Instruction Book For Tensioned Director Electrol POWER PRESENTATION PRODUCTS DA-LITE SCREEN COMPANY, INC. 3100 North Detroit Street Post Office Box 137 Warsaw, Indiana 46581-0137 Phone: 219/267-8101 800-622-3737 Fax: 219/267-7804 http:// www.da-lite.com e-mail: info@da-lite.com...

  • Page 2: Important Safety Instructions

    5. Install electric hook up that applies to your unit. Make sure to review your electrical installation checklist and wiring diagram (included) for either 120 volt switch, 220/240 volt switch, or DRC low voltage control. NOTE: Screen has been internally wired at Da-Lite. Wiring designated “external” is completed by installer conforming to local and national codes.

  • Page 3: Access Door Installation

    Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly ad- justed at Da-Lite. Should it be necessary to adjust for more or less drop of picture, proceed in the following manner:...
  • Page 4 MORE SCREEN DROP 1. Place operating switch in “down” position. 2. When the screen stops, turn the white “down” limit knob (Fig. 2) one-quarter turn counterclockwise. Test by raising picture surface approximately two feet, then lower again. Repeat until desired picture surface position is attained. NOTE: Must leave 1-1/2 wraps of fabric on roller.

  • Page 5: Wiring Diagram

    TENSIONED DIRECTOR ELECTROL INSTRUCTIONS RED (UP) 120V WIRING DIAGRAM BLACK (DOWN) RELAY WHITE BLACK PURPLE GRAY GREEN WHITE BLACK & YELLOW BLACK TO JUNCTION BOX MOUNTED IN SCREEN CASE, IN WHICH INTERNAL WIRING TERMI- WHITE DOOR SWITCH NATES IN WHITE, BLACK, AND RED LEADS.
  • Page 6 TENSIONED DIRECTOR ELECTROL INSTALLATION VARIABLE POSITION MOUNTING BRACKET ENDCAP MOUNTING FLANGE MOTOR END ELECTRICAL JUNCTION BOX 9-1/4" 8" 4" OR 6" 3/8" THREADED ROD ATTACHED TO MOUNTING BRACKET NOT INCLUDED 3/8" THREADED ROD ATTACHED TO ENDCAP FLANGE 7-3/16" NOT INCLUDED...

  • Page 7: Troubleshooting

    TROUBLESHOOTING SYMPTOM CAUSE SOLUTION 1. Screen will not operate or will not go (a) Blown facility fuse. (a) Replace facility fuse. “down”. Motor does not hum. (b) Tripped facility circuit breaker. (b) Reset facility circuit breaker. (c) No power to operating switch or (c) Check above.
  • Page 8 Da-Lite personnel. Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise. Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.

Table of Contents