Default Programming - Fire-Lite MS-9200UDLS User Manual

APPENDIX B
Program Option
Detector Programming
Detector Type
Detector Verification
Detector Walktest
Detector PAS
Detector Presignal
Detector Zone Assign.
Detector Adj/Noun
Module Programming
Module Type
Module Walktest
(not used)
Module Presignal
Module Zone Assign.
Module Adj/Noun
Zone 0 Enable
Zone 1 Enable
Zone 2 Enable
Zone 3 Enable
.........................through..........
Zone 96 Enable
Zones 97, 98 & 99
(future)
Loop Style
Loop Protocol
Trouble Reminder
Banner
Time Format
Hours Setting
Minutes Setting
Second Settings
AM-PM Setting
Month Setting
Day Setting
Year Setting
Daylight Savings
Month Start Daylight Savings
Week Start Daylight Savings
Month End Daylight Savings
Week End Daylight Savings
Verification
PAS Timer
Presignal Timer
Waterflow Retard Timer
NAC 1, 2, 3 & 4 Enable
NAC 1, 2, 3 & 4 Silenceable
NAC 1, 2, 3 & 4 Type
NAC 1, 2, 3 & 4 Sync Type
NAC 1, 2, 3 & 4 Autosilence
NAC 1, 2, 3 & 4 Coding
NAC 1, 2, 3 & 4 Zones
NAC 1, 2, 3 & 4 Silence Inhibit
MS-9200UDLS PN 52750:E1

Default Programming

The following table provides a list of the programming options and their factory default
settings.
Factory Default
Not Installed Relay 1
Smoke-Photo Relay 2
Off Relay 3
Yes Annunciator Terminal Mode
No Annunciator ACS Mode
No UDACT
000 only ACS Installed
none Onboard DACT
Not Installed Printer-PC
Monitor Printer Baud
Yes Service Terminal Panel ID
Ring Count
No Primary Phone Type
000 only Secondary Phone Type
none DACT Communication
Enabled AC Loss Delay
Enabled Backup Reporting
Enabled Primary Reporting Style
Enabled Secondary Reporting Style
..................... Primary Account Code
Enabled Secondary Account Code
Enabled Primary 24 Hour Test Time
Secondary 24 Hour Test Time
Style 4 Primary Phone Number
LITESPEED Secondary Phone Number
Off Primary DACT Format
Secondary DACT Format
12 Hr ANN Enabled
12 ANN-BUS Modules Addr. 1 - 8
00 ANN-S/PG Port
ANN-S/PG Baud
AM ANN-S/PG Data Bits
01 ANN-S/PG Parity
01 ANN-S/PG Stop Bits
00 ANN-S/PG Offline Timer
Enabled ANN-S/PG Printer Supervision
March ANN-80 Piezo Enabled
Week 2 ANN-80 Lock Enabled
November ANN-80 Acknowledge Button Enabled
Week 1 ANN-80 Silence Button Enabled
OFF ANN-80 Reset Button Enabled
0 ANN-80 Drill Button Enabled
0 ANN-I/O Point/Zone
0 ANN-I/O Range
Enabled ANN-I/O Active LEDs Only
Yes ANN-RLY Relay 1
Bell ................through.......................
System Sensor ANN-RLY Relay 10
0 ANN-LED Point/Zone
Steady ANN-LED Alarms/ATS (Alarm, Trbl, Supv)
Zone 000 only ANN-LED Range
No
01/27/09
Program Option
Default Programming
Factory Default
Alarm
Trouble (fixed)
Supervisory
No
No
No
No
No
No
9600
0000
0
Touchtone
Touchtone
OFF
2
First Available
Report Point
Report Point
0000
0000
0100
0200
Ademco Contact ID
Ademco Contact ID
No
None
Parallel
9600
7
Even
1
60
No
Yes
Yes
Yes
Yes
Yes
Yes
Zone
00-29
Zone 1
............
Zone 10
Zone
ATS
0 - 9
197