Service Call Errors; Warnings - Canon PIXMA iP6000D Service Manual

2-2. Service Call Errors (by LED Blinking in Orange and Green Alternately, or Lit in Orange)
LED alternate
blinking in orange and
green
2 times Carriage error [5100]
3 times Paper feed error [6000]
4 times Purge unit error [5C00]
5 times ASF (cam) sensor error [5700]
6 times Internal temperature error [5400]
7 times Waste ink absorber full [5B00]
8 times Print head temperature rise error [5200]
9 times EEPROM error [6800]
11 times Carriage lift mechanism error [5110]
12 times AP position error [6A00]
13 times Paper feed position error [6B00]
14 times Paper feed cam sensor error [6B10]
15 times USB Host VBUS overcurrent [9000]
16 times Valve sensor error [6C00]
17 times Motor driver error [6D00]
20 times Other hardware error [6500]
Continuous alternate ROM error
blinking
Lights in orange RAM error
*1: Before replacement of the logic board ass'y, check the waste ink amount (by service test print or EEPROM information print). If the waste ink amount is 7%
or more, also replace the bottom case unit (QM2-1496) or the ink absorbers (QC1-4221/ 4222 / 4223 / 4224 / 4257 / 4263 / 4264 / 4864 ) when replacing
the logic board ass'y.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]
*2: Reset the waste ink counter when replacing the bottom case unit.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]

2-3. Warnings

Printer (displayed on the LCD viewer):
Displayed warning
Low ink of 6BK, 6C, 6M, 6Y, 6PC, or 6 PM (at
detection of no remaining raw ink)
Print head temperature rise
Protection of excess rise of the print head temperature
*1: If the warning is displayed, the carriage does not move to the ink tank replacement position when the access cover is opened.
1 - 4
Error [Error code]
- Carriage unit (QM2-1499)
- Timing slit strip film (QC1-4284)
- Logic board ass'y (QM2-1786)*1
- Carriage motor (QK1-0545)
- Timing sensor unit (QM2-1213)
- Timing slit disk film (QC1-4833)
- Feed roller ass'y (QL2-0598)
- Platen unit (QM2-1510)
- Logic board ass'y (QM2-1786)*1
- Paper feed motor (QK1-0550)
- Purge unit (QM2-1500)
- Logic board ass'y (QM2-1786)*1
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1786)*1
- Ink absorber (QC1-4221 / 4222 / 4223 / 4224 / 4257 / 4263 / 4264 / 4864 )
- Bottom case unit (QM2-1496)*2
- Print head (QY6-0050)
- Logic board ass'y (QM2-1786)*1
- Logic board ass'y (QM2-1786)*1
- Lift shaft(QC1-4331)
- Photo interrupter (WG8-5624)
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1786)*1
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1786)*1
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1786)*1
- Sheet feed unit (QM2-1220)
- Logic board ass'y (QM2-1786)*1
- Logic board ass'y (QM2-1786)*1
- Logic board ass'y (QM2-1786)*1
- Logic board ass'y (QM2-1786)*1
- Logic board ass'y (QM2-1786)*1
- Logic board ass'y (QM2-1786)*1
- Logic board ass'y (QM2-1786)*1
If the print head temperature is high when the access cover is opened, the warning is displayed*1.
When the print head temperature falls, the warning is released.
If the print head temperature exceeds the specified limit, a Wait is inserted during printing,
Solution
(Replacement of listed parts, which are likely to be faulty)
Remarks