Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Crestron CH-DIM4-D9
Summary of Contents for Crestron CH-DIM4-D9
- Page 1 Crestron CH-DIM4-D9 Dimmer Control Interface (DIN Rail) Operation Guide...
-
Page 2: Table Of Contents
Cresnet connections……………………………………………………… 6 Cresnet ID…………………………………………………………….…… 7 Programming Configuration Manager................ 8 Programming Manager..............9 Example Program................9 Problem Solving Troubleshooting.................10 Futher Inquiries..................11 Crestron International • 2 Oude Keerbergsebaan • 2820 Rijmenam • Belgium Tel: +32 15 50 99 50 • info@crestron-int.be • www.crestron-int.be... -
Page 3: Description
Figure 1: CH-DIM4-D9 Functional Description The CH-DIM4-D9 is an analog output interface for control of fluorescent dimmable ballasts. 4 Cut-off relay’s are implemented to cut the 230V feed to the load if the analog output is <1VDC. This is to prevent the Fluorescent light from flickering (Figure 1). -
Page 4: Technical Data
Interface with 2x 4, 1x 5 and 1x 2 Pole Mini-Phoenix connectors. Front view Figure 2: Front view CH-DIM4-D9 Crestron International • 2 Oude Keerbergsebaan • 2820 Rijmenam • Belgium Tel: +32 15 50 99 50 • info@crestron-int.be • www.crestron-int.be... -
Page 5: Setup
CH-DIM4-D9 Product Manual Setup Example wiring diagram Figure 3: Connection diagram CH-DIM4-D9 Crestron International • 2 Oude Keerbergsebaan • 2820 Rijmenam • Belgium Tel: +32 15 50 99 50 • info@crestron-int.be • www.crestron-int.be... -
Page 6: Cresnet Connections
(DOC5411i). Refer to figure 4 and connect the CH-DIM4-D9 to the Cresnet network via a Cresnet network cable (CRESNET cable). This cable is not supplied with the CH-AO12-D5 but can be obtained from Crestron International. -
Page 7: Cresnet Id
The NET ID of each unit must match an ID code specified in the Simpl Windows program. Use the following method to change NET ID of the CH-DIM4-D9 1. Locate the two miniature rotary switches labeled HIGH and LOW on the bottom face (refer to figure 5). -
Page 8: Programming
OPS and software versions* Configuration manager A CH-DIM4-D9 needs to be defined as a CNLDAB-4A in Simpl Windows (Figure 6). Figure 6: Hardware configuration CNLDAB-4A Crestron International • 2 Oude Keerbergsebaan • 2820 Rijmenam • Belgium Tel: +32 15 50 99 50 • info@crestron-int.be •... -
Page 9: Programming Manager
This example illustrates how sliders on a touch panel control the four analog outputs of the CH-DIM4-D9. The Analog Initialize symbol sets the value on which the four relays should do the cut-off, in this case on 4 different values. -
Page 10: Problem Solving
Troubleshooting Table 1 Provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron Technical Support representative or submit your question on the Crestron True Blue On Line Service (www.crestron.com) Table 1: Troubleshooting Guide POSSIBLE CAUSE(S) -
Page 11: Futher Inquiries
Product Manual Further Inquiries If after reviewing this Operations Guide on the CH-DIM4-D9, you cannot locate specific information or have questions, please take advantage of Crestron's award winning customer service team by calling: • In Europe, call Crestron International at +32-15-50-99-50.