Information On Dv Dubbing - FUNAI WD6D-D4413DB Owner's Manual

When you want to record to a videotape:
Press [VCR].
Insert a videotape with a record tab into the
cassette compartment.
3
Select the input terminal to which the external
equipment is connected (AV1 or AV2).
Press [INPUT SELECT] repeatedly to select the external
input mode, then press [PROG.
select AV1 or AV2.
4
Select a recording speed using [REC SPEED].
Refer to "Recording Speed" on page 28 for DVD or page
70 for VCR.
5
Press [RECORD I] (DVD / VCR) on the unit to
start recording.
6
Press the [PLAY B] button on the external
equipment.
7
For disc:
Press on the unit to stop
[STOP C]
recording.
For videotape:
Press
[STOP EJECT C A]
recording.
Note
• During recording, recording will be paused when a signal
other than PAL or SECAM is detected. (See "Video Colour
System" on page 37 for details.)
• The signal from the external device will be output automatically
when the TV is connected to AV1 and the external device is
connected to AV2 using a Scart cable with its power on.
(However, it will not be output when this unit's power is turned off.)
If you want to monitor this unit's signal, press [DISPLAY]
or turn the external device off. (The signal from this unit can
only be monitored during playback.)
If you want to monitor the signal from other input, press
[DISPLAY], then press [INPUT SELECT] to select the
desired external input mode, then select the desired input
channel using [PROG.

Information on DV Dubbing

This function helps you to dub the contents in the DVC (digital
video camcorder) to DVD or VCR easily. (See page 71 for
DVC to VCR Dubbing.)
You can control basic operations of the DVC from the remote
control of this unit if the DVC is in video mode.
Guide to DV and On-Screen Display
1
Connect your DVC to the DV-IN jack on the front
panel using a DV cable. (Use the DV cable that
has 4-pin input jack and is compliance with the
IEEE 1394 standards.)
2
Press [INPUT SELECT] repeatedly to select the
external input channel, then press
[PROG. ] repeatedly to select DV(AV3).
38
EN
] repeatedly to
on the unit to stop
].
3
Press [DISPLAY] to display the DVC information
on the screen.
When the DVC is in video mode...
1/ 1 1/ 1
T C
1
2
Cont r ol D VD
D V A udio Stereo1
Sta r t Rec
3 4
When the DVC is in camera mode...
1/ 1 1/ 1
T C
The menu changes according to the mode of DVC.
Switch the mode on the DVC to video mode for the dubbing
information.
The following instructions are described with the
operations using the remote control of this unit.
1 DV icon
2 Indicator of active device
• With "Control" highlighted, press [ENTER OK] to display
the available devices to control with the remote control
of this unit. Select the device you want to operate using
[K L], then press [ENTER OK].
- Select "DVD" to control this unit with the remote control
of this unit.
- Select "DVC" to control your DVC with the remote
control of this unit.
3 Recording audio mode
• "DV Audio" can be changed. With "DV Audio" selected,
press [ENTER OK] to display "DV Audio" menu. Select
the audio you want to output using [K L], then press
[ENTER OK].
- Select "Stereo1" to dub the stereo sound.
- Select "Stereo2" to dub the sound that was added after
the recording.
- Select "Mix" to dub the stereo1 and stereo2.
4 Command menu
• "Start Rec" or "Pause Rec" will appear.
5 External input channel
6 Product name of your DVC
• If the unit cannot recognise the input signal from the
DVC or if it is the unknown product, "No Device" or "****"
will appear instead.
- R W VR ORG
DV
AB-1234
0:12:34
D VD 2H 2:00
- R W VR ORG
5
DV
AB-1234
0:12:34
D VD 2H 2:00
7 6