Elite Screens Evanesce B Series User Manual

Elite Screens Evanesce B Series User Manual

In-ceiling electric motorized front projection screen
Hide thumbs Also See for Evanesce B Series:

Advertisement

In-Ceiling Electric Motorized Front Projection Screen
Important Safety & Warning Precautions
Make sure to read this user's guide and follow the procedures below.
Caution: The screen's Black Top Drop is already set to its maximum drop distance. There is NO extra
Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.
Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to
this unit are prohibited and will void your warranty. For more information, please contact our Technical
Support Department at (877) 511-1211 Ext. 604.
Please retain this user's guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by
the manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
The power outlet supplying power to the unit should be close to the unit and easily accessible.
Do not install the unit on uneven, inclined surfaces;
Do not install in damp places to avoid an electric shock or short circuit.
Do not place any heavy objects over the power cord.
Position the power cord properly to avoid creating a trip obstacle.
To avoid an electrical shock or fire, due to a loose contact or short circuit, do not overload the
power cord.
The internal & external parts of this unit are not end user serviceable. Do not attempt to
disassemble this unit by yourself. No one except authorized technicians can open and make
repairs to this unit.
Make sure the power source that this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure the cord has an equal rating as the
appliance to avoid over heat.
Do not handle the power plug when your hands are wet or your feet are in contact with water.
Properly dispose of this equipment according to the environmental regulations in your area
when product is no longer of service.
Rev.102212-JA
Evanesce B Series
User's Guide
1
www.elitescreens.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Evanesce B Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Elite Screens Evanesce B Series

  • Page 1 Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void your warranty.
  • Page 2: Installation Warning

    The installer must insure that proper mounting hardware is used to provide adequate strength suitable for the installation. Elite Screens is not liable for any faulty installations. For limit adjustment instructions, please contact our Technical Support Department at (877) 511-1211 Ext.
  • Page 3 D. 3-way Batteries x 2 receiver wall switch Control System for Evanesce B Series RJ45 input 1. 5-12V Trigger: The built-in 5-12V trigger input allows your screen to synchronize its drop & rise with the projector’s power cycle. The screen deploys when the projector powers up and will retract when the projector powers down.
  • Page 4: Installation Instructions

    The Aerie Tension Series includes a 3-Prong Power Cord for use in a non-concealed power outlet. If your installation will be entirely concealed (including power outlet), Elite Screens strongly recommends a hardwire connection. Please refer to the image below for both 110v & 220v wiring information.
  • Page 5 A. Above ceiling installation instructions Assembly 1. Place the hanging bracket (A) over the left and right side ends of the housing and secure each one using the M8x40mm hex screw (G), M8x16mmx1.5mm washers (C) and M8 nut (E) as shown below.
  • Page 6 3. Insert the end flange piece (C) on the edge of the housing as shown below to complete the assembly. The screen is now ready for installation. Push end flange piece into housing end until it snaps in Dimensions Table: For Above ceiling installation reference Rev.102212-JA www.elitescreens.com...
  • Page 7: Screen Installation

    B. Below ceiling installation instructions Please make sure all parts listed below are included before proceeding with the installation. Hardware Parts List for below ceiling installation A. End Flange x 2 B. Hanging bracket x 2 C. Threaded rod x 4 D.
  • Page 8 3. The M8 expanding bolts (G) mount into thick wood beams, stone or concrete and will support the screen. Use the Socket wrench (D) to attach the M8x40mm hexagonal screws. The expanding bolts should be firmly tightened and tested to make sure that they will hold the weight of the screen. 4.
  • Page 9 6. Install end flange cover panel (A) between the gap and the screen to complete the installation. Dimensions Table: For below ceiling installation reference Ceiling Ceiling Ceiling For local Elite Screens contact or Technical Support, please visit www.elitescreens.com Rev.102212-JA www.elitescreens.com...

Table of Contents