NOTE: Please read all instructions carefully before using this product ® MARCY DIAMOND Table of Contents Safety Notice DELUXE CAGE Hardware Identifier MD-8870 Assembly Instruction Parts List Warranty Ordering Parts Model MD-8870 Retain This Manual for Reference 100712 OWNER'S MANUAL ®...
BEFORE YOU BEGIN ® ® Thank you for selecting the MARCY DIAMOND MD-8870 by IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1.
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Base, and Bench Rear Stabilizer. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown.
CAGE ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Insert a Side Base Frame (#4) into the Rear Right Vertical Frame (#2).
Page 10
STEP 2 (See Diagram 2) A.) Do not tighten the Nuts and Bolts until instructed to do so. B.) Insert a Side Base Frame (#4) into the Rear Left Vertical Frame (#3). Secure it with two M10 X ¾” Allen Bolts (#72) and two Ø ¾” Washers (#81). C.) Attach a Front Vertical Frame (#1) onto the Side Base Frame.
Page 11
STEP 3 (See Diagram 3) A.) Do not tighten all Nuts and Bolts until instructed to so. B.) Attach the Rear Base Frame (#7) to the Rear Right & Left Vertical Frame (#2 & #3). C.) Secure each end with four M10 x ¾” Allen Bolts (#72) and four Ø ¾” Washers (#81). D.) Attach the Middle Vertical Frame (#8) onto the Rear Base Frame.
Page 13
STEP 4 (See Diagram 4) A.) Slide the Sliding Weight Post (#22) onto the Weight Glide Post (#16). The triangular bracket on Sliding Weight Post needs to be behind the Weight Glide Post and facing upward. B.) Attach the Weight Glide Post to the Lat Bar Frame (#17). Attach one 3 1/8” x 1 ¾” Bracket (#29) to the Weight Glide Post.
Page 16
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 122” Cable (#62) to the bracket under the Lat Bar Frame (#17). Attach a Pulley (#39) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#76), two Ø ¾” Washers (#81), and one M10 Aircraft Nut (#83).
Page 18
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of 79” Butterfly Cable (#63) to the clip on Left Butterfly (#11). Draw the Cable to the left Swivel Pulley Bracket (#14). B.) Attach a Pulley (#39) to the Bracket. Secure it with one M10 x 2” Allen Bolt (#75), two Ø ¾” Washers (#81), two Cable Retainers (#59), and one M10 Aircraft Nut (#83).
Page 20
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Draw the 122” Cable (#62) through the opening on Foot Plate (#35) to the opening on bottom of Middle Vertical Frame (#8). B.) Attach a Pulley (#39) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#74), two Ø 1”...
Page 22
STEP 8 (See Diagram 8) A.) Place the two Weight Bar Safety Catch Frames (#9) onto the selected open slots on the Vertical Frames (#1, #2, #3). B.) Attach Insert the Left & Right Bar Holders (#20 & 21), the Left & Right Safety Catches (#18 &...
MULTI-PURPOSE BENCH ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten Nuts and Bolts until instructed to do so.
Page 28
STEP 2 (See Diagram 2) A.) Attach the Incline Support (#8) to the middle side holes on the two Backrest Supports (#7). Secure it with one M10 x 6 7/8” Allen Bolt (#26), two Ø ¾” Washers (#35), and one M10 Aircraft Nut (#37). Do not tighten the Nut and Bolt yet.
Page 29
STEP 3 (See Diagram 3) A.) Place the Backrest Board (#11) onto the Backrest Supports (#7). Secure it with four M8 x 1 5/8” Allen Bolts (#32) and 5/8” Washers (#36). B.) Place the Seat Pad (#10) onto the two Seat Brackets (#4). Secure it with four M8 x 1 1/8”...
Page 30
STEP 4 (See Diagram 4) A.) Attach the Leg Developer (#5) to the open bracket on the Front Post (#2). Secure it with one M10 x 3” Allen Bolt (#29), two ¾” Washers (#35), and one M10 Aircraft Nut (#37). B.) Insert the Leg Developer Weight Post (#6) into the hole on Leg Developer.
MULTI-PURPOSE BENCH PARTS LIST KEY NO. DESCRIPTION Q’ty Main Frame Front Post Rear Stabilizer Seat Bracket Leg Developer Leg Developer Weight Post Backrest Support Incline Support Front Stabilizer Seat Pad Backrest Board 5/8” x 1 1/8” End Cap Foam Tube Foam Roll Olympic Sleeve Foam Roll End Cap...
® IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser.