Summary of Contents for Impex MARCY DIAMOND ELITE MD-857
Page 1
NOTE: Please read all instructions carefully before using this product MARCY DIAMOND ELITE Table of Contents OLYMPIC BENCH Safety Notice Hardware Identifier MD-857 Assembly Instruction Parts List Warranty Ordering Parts Model MD-857 Retain This Manual for Reference 08-05-09 OWNER'S MANUAL ®...
PARTS LIST………….…………...............………. 12 WARRANTY....................…………. 13 ORDERING PARTS..................………… 13 BEFORE YOU BEGIN Thank you for selecting the Marcy Diamond Elite MD-857 BENCH by ® IMPEX INC. For your safety and benefit, read this manual carefully before using the machine. As a manufacturer, we are committed to provide you complete customer satisfaction.
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
WARNING LABEL PLACEMENT The Warning Label shown here has been placed on the Front Stabilizer. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the label in location shown...
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Do not tighten all nuts and bolts until instructed to do so. B.) Attach the Left Upright Beam (#1) to a Rear Stabilizer (#3).
Page 8
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Attach the Leg Developer Support (#13) to the Front Stabilizer (#14). Secure it with three M10 x 5/8” Allen Bolts (#63) and ¾”...
Page 9
STEP 3 (See Diagram 3) A.) Attach the holes on the end of the Backrest Supports (#21) to the long pivot on the Sliding Block (#15). Attach the Backrest Board (#26) to the Backrest Supports. Secure it with four M8 x 1 5/8” Allen Bolts (#65) and Ø5/8” Washers (#67). Place the Backrest Board against the Backrest Adjustment Bar.
Page 10
STEP 4 (See Diagram 4) A.) Insert the U-shaped Pin (#49) into the open slot on the Leg Developer Support (#13). Secure it with one M6 x ½” Philips Screw (#47), Ø ½” Washer (#48), and Spring (#50). B.) Attach the Leg Developer (#10) to the Leg Developer Support. Secure it with an Axle (#55), two M10 x 5/8”...
Page 11
STEP 5 (See Diagram 5) A.) Attach the Arm Curl Pad (#28) to the Arm Curl Stand (#9). Secure it with two M8 x 5/8” Allen Bolts (#64) and Ø 5/8” Washers (#67). B.) Insert the Arm Curl Stand into the top opening on the Leg Developer Support. Use a M18 Lock Knob (#42) to secure the Stand.
PARTS LIST KEY NO. DESCRIPTION Q’ty 4 ½” L-shaped Pin Left Upright Beam 3 7/8” Lock Pin Right Upright Beam 4” L-shaped Pin Rear Stabilizer Spring Clip Main Seat Support Axle Cross Brace M10 x 3 ½” Carriage Bolt Backrest Adjustment Bar M10 x 2 ¾”...
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be prepaid by the customer. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage.