Spirit XT485 Owner's Manual page 18

Belt/Deck Lubrication Procedure
Do not lubricate with other than Spirit Fitness approved lubricant.
Your treadmill comes with one tube of lubricant and extra tubes can
be ordered directly from Spirit Fitness or your authorized Spirit Fitness
dealer.
Keeping the deck lubricated at the recommended intervals ensures
the longest life possible for your treadmill. If the lubricant dries out, the
friction between the belt and deck rises and places undue stress on
the drive motor, drive belt and electronic motor control board, which
could result in catastrophic failure of these expensive components. Failure to lubricate the deck at regular
intervals may void the warranty.
The belt & deck come pre-lubricated and subsequent lubrication should be performed every 180 hours
of use. The console has a built in lubrication reminder indicator that lights every 180 hours of use.
Use the lubricant to lubricate the deck beneath the belt. If you can reach under the belt approximately
6" on each side, use the following procedure: Unplug the electrical cord. At the middle of the deck, lift up
on the belt and reach under with the tube of lubricant. Squirt most of the lubricant on the deck surface.
Repeat the process on the opposite side. Plug the electrical cord back into the outlet and walk on the belt
at a moderate speed for five minutes.
If unable to perform the above procedure, it will be necessary to loosen the walking belt. Using the 6
mm Allen wrench supplied, loosen the two rear roller adjustment bolts -- located in the rear end caps –
enough to get your hand under the belt (5 –10 turns). Make sure to loosen both bolts the same amount
of turns and also remember how many turns, because when finished you will need to tighten the bolts
back to the point they were before.
Once the belt is loose, wipe the deck with a clean lint free cloth to remove any dirt. Apply the whole
tube of lubricant onto the deck surface about 18 inches from the motor cover. Squeeze out the contents
of the tube across the deck (parallel to the motor cover) in about a one-foot line, like toothpaste on a
toothbrush. The one-foot line should be in the middle of the deck at approximately equal distance from
both side edges of the belt. You want the lubricant to be applied about the spot that your feet would hit
the belt as you are walking. This should be about 18 inches from the motor cover, but you may want to
walk on the treadmill before loosening the belt to note where your feet land on the belt. If you mostly use
the treadmill for running, the spot where your feet land may be different from walking.
Once the lubricant is applied, tighten the rear roller bolts the same amount of turns as when you
loosened them. Run the treadmill at about 3 mph without walking on it for about a minute or two to
make sure the belt stays in the middle of the deck. If the belt tracks to one side then follow the belt
tracking instructions to remedy. Now the deck is lubricated and you should walk, not run, on the treadmill
immediately for at least 5 minutes to ensure the lubricant is evenly distributed.
30
XT485
T readmill
Problem Solution/Cause
Display does not light
1.
2.
3.
4.
5.
Tread-belt does not stay centered The user may be walking while favoring or putting more
weight on either the left or right foot. If this
Treadmill belt hesitates when
walking pattern is natural, track the belt slightly
walked/run on
off-center to the side opposite from the belt
movement. See General Maintenance section on
Tread-belt Tension. Adjust as necessary.
Motor is not responsive after press-
1.
ing start
2.
Treadmill will only achieve This indicates motor should be receiving power to
operate. Low AC voltage to treadmill. Do not use an
approximately 7 mph but shows higher
extension cord. If an extension cord is required it should
speed on display
be as short as possible and heavy duty 16 gauge
minimum. Low voltage. Contact an electrician or your
Spirit Fitness dealer. A minimum of 110 volt AC current
is required.
Tread-belt stops quickly/suddenly when
High belt/deck friction. See General Maintenance
section on cleaning the deck. If cleaning doesn't prevent
tether cord is pulled
this from reoccurring, check to see if there is significant
wear of the deck. If so, the deck may need to be flipped if
it is on its original side
Treadmill trips on board 15 amp circuit High belt/deck friction. See General Maintenance. If
cleaning doesn't prevent this from reoccurring, check the
amp draw of the motor. If this is high and there are signs
of significant wear of the deck, it may need to be flipped if
it is on its original side
Computer shuts off when console is Treadmill may not be grounded. Static electricity is
"crashing" the computer. Refer to Grounding
touched (on a cold day) while
Instructions on page 3.
walking/running
Circuit breaker trips, but not the
Need to replace the breaker with a "High In-rush current"
type breaker (see page 3 for details)
treadmill circuit breaker
31
Tether cord not in position.
Circuit breaker on front grill tripped.
Push circuit breaker in until it locks.
Plug is disconnected. Make sure plug is firmly pushed
into 115 VAC wall outlet.
Breaker panel circuit breaker may be tripped.
Treadmill defect. Contact your Spirit Fitness dealer.
If the belt moves, but stops after a short time and
thedisplay shows "LS", run calibration.
If you press start and the belt never moves, then the
display shows LS, contact service.
XT485
T readmill