Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Billion Manuals
  4. Wireless Router
  5. BiPAC 7300GX
  6. Quick install manual

Billion BiPAC 7300GX Quick Install Manual

Adsl2/2+ modem/router with 3g back-up qos firewall wireless multi-port switching hub
Hide thumbs Also See for BiPAC 7300GX:

Advertisement

Quick Links

Download this manual See also: User Manual
BiPAC 7300GX
ADSL2/2+ Modem/Router with 3G back-up
QoS Firewall Wireless
Multi-Port Switching Hub
UK Quick Install Guide
This guide covers only the initial
Internet set-up. Please refer to
the full User Manual on the CD-
ROM for more advanced
settings. This guide is based on
the Billion BiPAC 7300GX
3G/ADSL2+ Wireless
Modem/Router. Screen shots in
this guide may vary slightly from
the actual router.
www.billion.uk.com

Advertisement

loading

Related Manuals for Billion BiPAC 7300GX

Summary of Contents for Billion BiPAC 7300GX

  • Page 1 Internet set-up. Please refer to the full User Manual on the CD- ROM for more advanced settings. This guide is based on the Billion BiPAC 7300GX 3G/ADSL2+ Wireless Modem/Router. Screen shots in this guide may vary slightly from the actual router.
  • Page 2 This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product.

  • Page 3: Quick Install Guide

    Username and Password and APN from your mobile service provider. 1.2 Steps for Connection: The following are the steps to properly connect your Billion 7300GX Modem/Router: 1. Turn off your computer. 2. If you do not have an ADSL faceplate installed by your service provider, you must ensure ADSL splitters (also called microfilters or filters) are fitted to all telephone sockets in use.
  • Page 4 6. Connect the Power adaptor to the Billion 7300GX Modem/Router and plug the other end into a Power outlet. Power up the unit. 7. Turn on your computer. Please allow up to 45 seconds for your Network Adaptor to locate the Router. Please wait for the DSL light on the front of the router to turn to solid –...
  • Page 5 3. From the Menu on the left select Quick Start. 4. Ensure the Connect Mode is ADSL (Recommended) and click on Continue.
  • Page 6 5. Enter your Username and Password as supplied by your Internet Service Provider in the relevant fields, and click on Continue. 6. Please wait while the router applies the new settings.
  • Page 7 7. Now click on Next to Wireless. N.B. If you do not go through the wireless setup on the Wizard, then you must click Save Config at the bottom of the page and then click Apply settings to save your username and password to Flash. 8.
  • Page 8 9. For WPA you should enter an alphanumeric password (numbers and letters) of between 8 and 64 characters in the WPA Shared Key field and click Continue. 10. Please wait while the router applies the new settings.
  • Page 9 11. This completes the wireless security configuration. 12. You should now be connected to the Internet. You can check your connection on the Status page by selecting Status from the menu on the left-hand side. 13. You are now ready to set up your 3G connection. To set up your 3G connection your 3G datacard with SIM must be inserted firmly into the slot in the back of the router before powering up the device.
  • Page 10 2.2 Setting up your 3G connection: You can configure your 3G connection to act as a backup (Autofailover mode), or as your primary connection. In both cases your 3G datacard with SIM must be inserted firmly into the slot in the back of the router before powering up the device. If your have completed your ADSL and wireless configuration and your 3G datacard was inserted when you first powered up the router, please select Status from the menu on the left-hand side and go to section 2.3 to configure your 3G.
  • Page 11 2.3 Configuration of your 3G connection in Autofailover mode: 1. From Status page, select Advanced>Configuration>WAN>WAN Interface. 2. Ensure Failover/Failback is ticked and then scroll down and click Apply at the bottom of the page. Now click the blue 3G icon in the Backup Port field.
  • Page 12 3. Enter your APN and Username and Password as supplied by your mobile service provider and click Apply. Some standard UK settings: Vodafone APN: internet APN: three.co.uk APN: mobile.o2.co.uk Username: web Username: guest Username: web Password: web Password: guest Password: password T-mobile Orange APN: general.t-mobile.uk...
  • Page 13 4. Click Apply to write your settings to Flash. 5. This completes the set up of your 3G connection in backup mode. If your ADSL connection goes down, the router will automatically Failover to your 3G connection. The Status page will look like this. N.B. The time it takes to Failover is dependant on the settings in the router and the 3G signal strength.
  • Page 14 2.4 Configuration of your 3G connection in primary mode: 1. To set the primary connection to 3G go to Advanced>Configuration>WAN> WAN Interface and select 3G from the drop down list in the Main Port field. 2. Click Apply to change the settings. Then click on Save Config at the bottom of the page and Apply to write your settings to Flash.
  • Page 15 3. The Status page will now show 3G as the primary mode of connection. If the 3G does not automatically connect then please click on Connect to activate your 3G service in primary mode. 4. The Status page will then show your 3G connection details.
  • Page 16 ADSL as your primary WAN interface. 4. Please check the Downloads section of our website at www.billion.uk.com/esupport for firmware upgrades for current card compatibility.