Before Operation; How To Operate The Oven; Memory Operation; Memory Cooking - Sharp R-1900M Operation Manual

B
EFORE OPERATION
* Before operating your new oven, make sure you read and
understand this operation manual completely.
1) Plug in the oven.
* The digital display will show " . "
2) Control panels can only be operated when the door is
closed.
3) Oven light will go on for 1 minute whenever the door is
opened or after cooking.
Cancellation:
1. Cooking data is canceled when keys are not pressed for
more than three minutes when setting programming.
2. Cooking stops when the STOP/CLEAR pad is pressed and
cooking data remains. However if subsequent keys are
not pressed within three minutes, cooking data will be
canceled. To resume cooking press the START pad.
HELPFUL TIPS for the Memory Input Method
The Memory Input Method determines how to input memory numbers for Memory Cooking and Custom Setting and Saving
memories, therefore follow the method below. Refer to HELPFUL TIPS below as well as in Memory cooking.
1. Dual Digit Input: Must input two numbers to select a
memory, even though the fi rst number is 0. Memory
programming is limited to 0 - 99.
2. Single Digit Input: Can only input one number to select
a memory. Memory programming is limited to 0 - 9.
3. Repeat Digit Input: Input one, two, or three numbers
to select a memory. Memory programming is limited
to 0 - 29.
4. For Repeat Digit Input/Auto Start ON only, push number
pads within one second of the previous number.
5. Regardless of Input Method selected, Counter Check/Clear (Custom Setting 7) and Multiplication Factor for Double/ Triple
Quantity (Custom Setting 10) only use the Dual Digit Input Method. As for Custom Setting 10, enter memory number
after pressing the DOUBLE/TRIPLE QUANTITY pad.
H
OW TO OPERATE THE OVEN

MEMORY OPERATION

Memory Cooking

* Your oven has 100 memory banks from 0 to 99. Memory
contents from memory number 0 to 29 are same in Dual,
Single and Repeat Digit Input methods.
* Memory 0 - 9 are programmed as factory settings. See
the table of Programmed Memories on the right side.
Memory 10 - 99 must be programmed before using
Memory Cooking. When a memory number which has
not been programmed is entered, End will be shown in
the display. See Saving Memories page 17 - 21 to program
a new memory.
R-1900M [EN].indd Sec1:7 R-1900M [EN].indd Sec1:7
3. Cooking stops when the door is opened and cooking data
remains. However once the door is closed, cooking data
will be canceled if subsequent keys are not pressed within
3 minutes. To resume cooking press the START pad.
4. Cooking is immediately canceled by pressing the STOP/
CLEAR pad twice.
Checking food:
Press the STOP/CLEAR pad then open the door, check
food, close the door and press the START pad to continue
cooking.
Cooking Completion:
When food is not taken out after cooking completion, End will
be shown in the display until the food is taken out.
The Memory Input Method
Memory No.
0
Examples
Memory
Input Method
Dual Digit Input 0, 0
Single Digit Input
0
Repeat Digit Input 0
Programmed Memories
Memory No. Cook time (sec.)
1
2
3
4
5
6
7
8 1 min. 15 sec.
9 1 min. 30 sec.
0
7
2 12 22
0, 2 1, 2 2, 2
2
2 2, 2 2, 2, 2
Output power
5 100%
10 100%
20 100%
30 100%
40 100%
50 100%
1 min. 100%
100%
100%
2 min. 100%
9/29/08 6:17:07 PM 9/29/08 6:17:07 PM