Page 1
Monday-Saturday 7:00 am-8:00 pm EST TO PREVENT DAMAGE AND BODILY HARM, ENSURE ENTIRE MANUAL HAS BEEN READ BEFORE OPERATING PRESSURE WASHER UNIT. ANY QUESTIONS OR CONCERNS REGARDING THIS MANUAL SHOULD BE DIRECTED TO THE SIMONIZ TOLL-FREE NUMBER. P a g e...
SAFETY INSTRUCTIONS WARNING To reduce the risk of serious injury, read all instructions and precautions before operating this machine. SYMBOL MEANINGS: This symbol warns you of possible toxic gases which can be harmful to your health or deadly if you are exposed to TOXIC them.
Page 4
INADEQUATE VENTILATION • Placing materials against or near the pressure washer or operating the unit in areas where the temperature exceeds 40°C ambient (such as storage rooms or garages) can interfere with its proper ventilation features causing overheating and possible ignition of the materials or buildings. •...
Page 5
This equipment is not designed for industrial use.. Please refer to icons above for suggested uses. For questions regarding other uses, please refer to our website at www.simoniz.ca or call us at 1-866-4SIMONIZ (1-866-474-6664). NEVER OPERATE UNDER THE FOLLOWING CONDITIONS •...
Page 6
SAFETY GLASSES • Always wear safety glasses while operating. DETERGENTS • Only use detergents recommended for pressure washers. Using detergents not specifically recommended for use with pressure washers can cause damage to pump and other pressure washer components. • DAMAGE CAUSED TO PRESSURE WASHER UNIT BY USING NON-RECOMMENDED DETERGENTS IS NOT COVERED UNDER WARRANTY.
PRESSURE WASHER FEATURES – Trigger Locking Latch –Will prevent from mis- – Oil Dipstick – Ensure the unit has the proper operating or spraying accidentally. level of oil before starting engine. Use only SAE 10W-30 oil. – Wand –Will extend your reach for easier cleaning. –...
Oil must be purchased separately. 3) Ensure both the pressure hose and garden Simoniz toll-free number 1-866-4SIMONIZ (1- hose have been correctly attached to the 866-474-6664) pressure washer pump. Ensure the water tap is...
Page 9
Insert bolt x1(L) through handle and Re-attach quick-connect coupler to secure with nutx1 and washerx1(L).Tighten with pump inlet (f). wrench (included) and screw driver(included) WAND ASSEMBLY Pull back the rubber shroud (g) to expose HOSE SUPPORT ASSEMBLY Attach the hose support (I) to right side of the the threaded fitting on the wand (B).
Page 11
To Check Oil Level; 1) Turn the oil gauge dipstick(A) counter clockwise; remove it and clean it with a clean cloth. (There are two ports to fill oil.) 2) Fully reinsert the oil gauge dipstick and pull it out to check the oil level. 3) If the oil level is halfway up the dipstick or below, refill with SAE 10W-30 oil through the dipstick hole until the oil level reaches 3/4 up...
PRE-START: CHECK AIR FILTER WARNING! The air filter should be checked after prolonged storage. The following steps should be followed when checking the air filter. It is recommended to replace the air filter every spring. 1) Unscrew the bolt(A) and remove the air filter cover(B).
Page 13
“Open” position. If motor fails to start, repeat steps 3-9 10. If you have problems starting the pressure washer, call the Simoniz toll-free number and one of our customer service representatives will be glad to assist you.
Page 14
Do not use powdered soaps which clog the injection system. • Follow the detergent manufacturer’s directions or call the Simoniz toll-free number if you have any questions or concerns. HOW TO USE DETERGENT WITH PRESSURE WASHER: 1) Ensure detergent siphon tubes are set up correctly.
NOTE: If your unit still is not functioning properly once you have used this guide please call the SIMONIZ Tool-free service number at 1-866-4SIMONIZ(1-866-474-6664). Please do NOT bring the unit back to the store until you have called this number.
Page 16
Use correct starting method, Refer Incorrect starting method to the instruction manual. Low oil or no fuel Check oil level and fuel Engine stops after Move the Choke lever to “Open” The choke at “Close” starting. position immediately after starting position the engine Clean or replace the air filter.
Page 17
Cold water keeps draining out of Defective thermal relieve CALL Customer Service Toll-Free thermal relieve valve. valve The detergent supply hose Connect detergent hose properly. is not connected. Refer to IM. Damaged detergent hose. Replace the detergent hose. Use black nozzle when applying Wrong nozzle detergent.
MAINTENANCE WATER INLET FILTER: • This pressure washer is equipped with a water inlet filter(A). • This water filter must be kept clean at all times or else it will restrict the water flow to the pressure washer and may damage the pump.
Page 19
1) Dismantle the spark plug wire (A) by pulling it off the spark plug (B). Using the supplied spark plug wrench, undo the spark plug by turning counter clockwise. 2) Check to see if there is carbon sediment build-up. If so, remove it. If the carbon sediment is excessive, replace the spark plug.
Page 20
6) Cover the pressure washer and store it in a clean, well ventilated and dry place. Ensure storage area is at room temperature. *** See in-store to purchase fuel stabilizer or pressure washer antifreeze. If you wish to drain the fuel instead of adding fuel stabilizer, please follow these steps: 1) Turn fuel shut-off valve to the “OFF”...
LIMITED WARRANTY This Simoniz® product has a limited 30-day over-the-counter replacement warranty, a 2-year repair warranty on the main unit against defects in manufacturing workmanship and materials and a 90-day warranty on included accessories. All warranty claims must be accompanied by proof of purchase.
Need help?
Do you have a question about the 039-8583-4 and is the answer not in the manual?
Questions and answers