Installation; Installation Room; Installation Cavity; Furniture/Fixtures - Thermador T24IF70NSP/47 Installation Instructions Manual

_{ii_@_1iiiiiiiYiYiYiYiYijii(_Jiii1i1iimYiiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiiiiiYiiiii1i_11_iiiiiYiiiiYiiiiYiiiiYiiiiYiiiiiYiiiiiYi1_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_
Installation
Do not install the appliance:
- outdoors,
- in an environment with dripping water,
- in rooms which are at risk of frost.
Appliance is very heavy - for empty weight see the
following table:
Refrigerator 24"
Refrigerator 30"
Freezer 18"
Freezer 24'
Freezer 30"
Wine unit 18"
Wine unit 24'
approx. 310 Ibs/140 kg
approx. 350 Ibs/158 kg
approx. 255 Ibs/115 kg*
approx. 300 Ibs/135 kg*
approx. 335 Ibs/150 kg*
approx. 300 Ibs/135 kg
approx. 360 Ibs/160 kg
(* without Water Dispenser)
Installation room
The appliance should be installed in a dry, ventilated room.
The ambient temperature should not drop below 55 °F (13 °C)
or rise above 110 °F (43 °C), otherwise malfunctions may
OCCUr,
The installation location should not be exposed to direct
sunlight and not placed near a heat source, such as an oven,
radiator, etc. If installation next to a heat source is
unavoidable, use a suitable insulating plate or observe the
following minimum distances from the heat source:
- 11/4" (30 ram) from an electric cooker,
- 12" (300 ram) from an oil or solid-fuel cooker.
Installation cavity
It is important to observe the specified dimensions of the
installation cavity for a trouble-free installation of the
appliance and for the subsequent general view of the
furniture front.
In particular ensure that the cavity is square.
Squareness can be checked by suitable means, e.g. spirit
level, diagonal measurements, etc
The minimum thickness of side walls and the top wall must
be 5/s" (16 ram).
The minimum thickness of toe kick panel must be 1/2" (13 ram).
A thickness of 3/4" (19 ram) is recommended.
Furniture/fixtures
The new appliance is screwed securely to adjacent and
overhead furniture/fixtures.
For this reason it is essential that all attachable furniture/
fixtures are connected securely to the base or the wall by
suitable means.
Base
A fully-load appliance is very heavy - for the load-
bearing capacity at least see the following table:
Refrigerator 24'
Refrigerator 30"
Freezer 18"
Freezer 24'
Freezer 30"
Wine unit 18"
Wine unit 24'
approx. 890 Ibs/400 kg
approx. 1110 Ibs/500 kg
approx. 560 Ibs/250 kg*
approx. 780 Ibs/350 kg*
approx. 950 Ibs/425 kg*
approx. 550 Ibs/245 kg
approx. 694 Ibs/310 kg
(* without Water Dispenser)
To ensure that the appliance is installed securely and
functions properly, the base must be flat and level.
The base must be made of a hard, rigid material.
The installation area must be the same height as the rest of
the room.
On account of the heavy weight of a fully loaded appliance,
a load-bearing base is required. If in doubt, contact an
architect or a building expert.
7